Quality of Service

This section refers to frames for all internal QoS functionality. Unless explicitly stated, the actions are independent of layer 2 frames or layer 3 packets.

Cumulus Linux supports several different QoS features and standards including:

COS and DSCP marking and remarking
Shaping and policing
Egress traffic scheduling (802.1Qaz, Enhanced Transmission Selection (ETS))
Flow control with IEEE Link Pause and PFC, and congestion control with ECN
Lossless and lossy RoCE

Cumulus Linux uses two configuration files for QoS:

/etc/cumulus/datapath/qos/qos_features.conf includes all standard QoS configuration, such as marking, shaping and flow control.
/etc/mlx/datapath/qos/qos_infra.conf includes all platform specific configurations, such as buffer allocations and Alpha values.

Cumulus Linux 5.0 and later does not use the traffic.conf and datapath.conf files but uses the qos_features.conf and qos_infra.conf files instead. Before upgrading Cumulus Linux, review your existing QoS configuration to determine the changes you need to make.

switchd and QoS

When you run Linux commands to configure QoS, you must apply QoS changes to the ASIC with the following command:

cumulus@switch:~$ sudo systemctl reload switchd.service

Unlike the restart command, the reload switchd.service command does not impact traffic forwarding except when the qos_infra.conf file changes, or when the switch pauses frames or controls priority flow, which require modifications to the ASIC buffer and might result in momentary packet loss.

NVUE reloads the switchd service automatically. You do not have to run the reload switchd.service command to apply changes when configuring QoS with NVUE commands.

Classification

When a frame or packet arrives on the switch, Cumulus Linux maps it to an internal COS (switch priority) value. This value never writes to the frame or packet but classifies and schedules traffic internally through the switch.

You can define which values are trusted: 802.1p, DSCP, or both.

The following table describes the default classifications for various frame and switch priority configurations:

Setting	VLAN Tagged?	IP or Non-IP	Result
PCP (802.1p)	Yes	IP	Accept incoming 802.1p marking.
PCP (802.1p)	Yes	Non-IP	Accept incoming 802.1p marking.
PCP (802.1p)	No	IP	Use the default priority setting.
PCP (802.1p)	No	Non-IP	Use the default priority setting.
DSCP	Yes	IP	Accept incoming DSCP IP header marking.
DSCP	Yes	Non-IP	Use the default priority setting.
DSCP	No	IP	Accept incoming DSCP IP header marking.
DSCP	No	Non-IP	Use the default priority setting.
PCP (802.1p) and DSCP	Yes	IP	Accept incoming DSCP IP header marking.
PCP (802.1p) and DSCP	Yes	Non-IP	Accept incoming 802.1p marking.
PCP (802.1p) and DSCP	No	IP	Accept incoming DSCP IP header marking.
PCP (802.1p) and DSCP	No	Non-IP	Use the default priority setting.
port	Either	Either	Ignore any existing markings and use the default priority setting.

If you use NVUE to configure QoS, you define which values are trusted with the nv set qos mapping <profile> trust l2 command (802.1p) or the nv set qos mapping <profile> trust l3 command (DSCP) .
If you use Linux commands to configure QoS, you define which values are trusted in the /etc/cumulus/datapath/qos/qos_features.conf file by configuring the traffic.packet_priority_source_set setting to 802.1p or dscp.

Trust 802.1p Marking

To trust 802.1p marking:

NVUE Commands

When 802.1p (l2) is trusted, Cumulus Linux classifies these ingress 802.1p values to switch priority values:

Switch Priority	802.1p (PCP)
0	0
1	1
2	2
3	3
4	4
5	5
6	6
7	7

The PCP number is the incoming 802.1p marking; for example PCP 0 maps to switch priority 0.

To change the default profile to map PCP 0 to switch priority 4:

cumulus@switch:~$ nv set qos mapping default-global trust l2
cumulus@switch:~$ nv set qos mapping default-global pcp 0 switch-priority 4 
cumulus@switch:~$ nv config apply

You can map multiple PCP values to the same switch priority value. For example, to map PCP values 2, 3, and 4 to switch priority 0:

cumulus@switch:~$ nv set qos mapping default-global trust l2 
cumulus@switch:~$ nv set qos mapping default-global pcp 2,3,4 switch-priority 0
cumulus@switch:~$ nv config apply

If you configure the trust to be l2 but do not specify any PCP to switch priority mappings, Cumulus Linux uses the default values.

To show the ingress 802.1p mapping for the default profile, run the nv show qos mapping default-global pcp command. To show the PCP mapping for a specific switch priority in the default profile, run the nv show qos mapping default-global pcp <value> command. The following example shows that PCP 0 maps to switch priority 4:

cumulus@switch:~$ nv show qos mapping default-global pcp 0
                 operational  applied  description
---------------  -----------  -------  ------------------------
switch-priority  4            4        Internal Switch Priority

Linux Commands

In the /etc/cumulus/datapath/qos/qos_features.conf file, set traffic.packet_priority_source_set = [802.1p].

When 802.1p marking is trusted, the following lines classify ingress 802.1p values to switch priority (internal COS) values:

traffic.cos_0.priority_source.8021p = [0]
traffic.cos_1.priority_source.8021p = [1]
traffic.cos_2.priority_source.8021p = [2]
traffic.cos_3.priority_source.8021p = [3]
traffic.cos_4.priority_source.8021p = [4]
traffic.cos_5.priority_source.8021p = [5]
traffic.cos_6.priority_source.8021p = [6]
traffic.cos_7.priority_source.8021p = [7]

The traffic.cos_ number is the switch priority value; for example 802.1p 0 maps to switch priority 0.

To map 802.1p 4 to switch priority 0, configure the traffic.cos_0.priority_source.8021p setting to 4.

traffic.cos_0.priority_source.8021p = [4]

You can map multiple values to the same switch priority value. For example, to map 802.1p values 0, 1, and 2 to switch priority 0:

traffic.cos_0.priority_source.8021p = [0, 1, 2]

You can also choose not to use a switch priority value. This example does not use switch priority values 3 and 4.

traffic.cos_0.priority_source.8021p = [0]
traffic.cos_1.priority_source.8021p = [1]
traffic.cos_2.priority_source.8021p = [2,3,4]
traffic.cos_3.priority_source.8021p = []
traffic.cos_4.priority_source.8021p = []
traffic.cos_5.priority_source.8021p = [5]
traffic.cos_6.priority_source.8021p = [6]
traffic.cos_7.priority_source.8021p = [7]

To apply a custom profile to specific interfaces, see Port Groups.

Trust DSCP

To trust ingress DSCP markings:

NVUE Commands

If DSCP (l3) is trusted, Cumulus Linux classifies these ingress DSCP values to switch priority values:

Switch Priority	Ingress DSCP
0	[0,1,2,3,4,5,6,7]
1	[8,9,10,11,12,13,14,15]
2	[16,17,18,19,20,21,22,23]
3	[24,25,26,27,28,29,30,31]
4	[32,33,34,35,36,37,38,39]
5	[40,41,42,43,44,45,46,47]
6	[48,49,50,51,52,53,54,55]
7	[56,57,58,59,60,61,62,63]

The DSCP number is the ingress DSCP value; for example DSCP 0 through 7 maps to switch priority 0.

To change the default profile to map ingress DSCP 22 to switch priority 4:

cumulus@switch:~$ nv set qos mapping default-global trust l3 
cumulus@switch:~$ nv set qos mapping default-global dscp 22 switch-priority 4 
cumulus@switch:~$ nv config apply

You can map multiple ingress DSCP values to the same switch priority value. For example, to change the default profile to map ingress DSCP values 10, 21, and 36 to switch priority 0:

cumulus@switch:~$ nv set qos mapping default-global trust l3 
cumulus@switch:~$ nv set qos mapping default-global dscp 10,21,36 switch-priority 0
cumulus@switch:~$ nv config apply

If you configure the trust to be l3 but do not specify any DSCP to switch priority mappings, Cumulus Linux uses the default values.

To show the DSCP mapping in the default profile, run the nv show qos mapping default-global dscp command. To show the DSCP mapping for a specific switch priority in the default profile, run the nv show qos mapping default-global dscp <value> command. The following example shows that DSCP 22 maps to switch priority 4:

cumulus@switch:~$ nv show qos mapping default-global dscp 22
                 operational  applied  description
---------------  -----------  -------  ------------------------
switch-priority  4            4        Internal Switch Priority

Linux Commands

In the /etc/cumulus/datapath/qos/qos_features.conf file, configure traffic.packet_priority_source_set = [dscp].

If DSCP is trusted, the following lines classify ingress DSCP values to switch priority (internal COS) values:

traffic.cos_0.priority_source.dscp = [0,1,2,3,4,5,6,7]
traffic.cos_1.priority_source.dscp = [8,9,10,11,12,13,14,15]
traffic.cos_2.priority_source.dscp = [16,17,18,19,20,21,22,23]
traffic.cos_3.priority_source.dscp = [24,25,26,27,28,29,30,31]
traffic.cos_4.priority_source.dscp = [32,33,34,35,36,37,38,39]
traffic.cos_5.priority_source.dscp = [40,41,42,43,44,45,46,47]
traffic.cos_6.priority_source.dscp = [48,49,50,51,52,53,54,55]
traffic.cos_7.priority_source.dscp = [56,57,58,59,60,61,62,63]

The # in the configuration file is a comment. By default, the file comments out the traffic.cos_*.priority_source.dscp lines.
You must uncomment them for them to take effect.

The traffic.cos_ number is the switch priority value; for example DSCP values 0 through 7 map to switch priority 0. To map ingress DSCP 22 to switch priority 4, configure the traffic.cos_4.priority_source.dscp setting.

traffic.cos_4.priority_source.dscp = [22]

You can map multiple ingress DSCP values to the same switch priority value. For example, to map ingress DSCP values 10, 21, and 36 to switch priority 0:

traffic.cos_0.priority_source.dscp = [10,21,36]

You can also choose not to use an switch priority value. This example does not use switch priority values 3 and 4:

traffic.cos_0.priority_source.dscp = [0,1,2,3,4,5,6,7]
traffic.cos_1.priority_source.dscp = [8,9,10,11,12,13,14,15]
traffic.cos_2.priority_source.dscp = [16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31]
traffic.cos_3.priority_source.dscp = []
traffic.cos_4.priority_source.dscp = []
traffic.cos_5.priority_source.dscp = [40,41,42,43,44,45,46,47,32,33,34,35,36,37,38,39]
traffic.cos_6.priority_source.dscp = [48,49,50,51,52,53,54,55]
traffic.cos_7.priority_source.dscp = [56,57,58,59,60,61,62,63]

To apply a custom DSCP profile to specific interfaces, see Port Groups.

Trust Port

You can assign all traffic to a switch priority regardless of the ingress marking.

NVUE Commands

The following commands assign all traffic to switch priority 3 regardless of the ingress marking.

cumulus@switch:~$ nv set qos mapping default-global trust port 
cumulus@switch:~$ nv set qos mapping default-global port-default-sp 3 
cumulus@switch:~$ nv config apply

To show the switch priority setting in the default profile for all traffic regardless of the ingress marking, run the nv show qos mapping default-global command:

cumulus@switch:~$ nv show qos mapping default-global
                 operational  applied  description
---------------  -----------  -------  ----------------------------
port-default-sp  3            3        Port Default Switch Priority
trust            port         port     Port Trust configuration

Linux Commands

In the /etc/cumulus/datapath/qos/qos_features.conf file, configure traffic.packet_priority_source_set = [port].

The traffic.port_default_priority setting defines the switch priority that all traffic uses.

To apply a custom profile to specific interfaces, see Port Groups.

Mark and Remark Traffic

You can mark or remark traffic in two ways:

Use ingress COS or DSCP to remark an existing 802.1p COS or DSCP value to a new value.
Use iptables to match packets and set 802.1p COS or DSCP values (policy-based marking).

802.1p or DSCP for Marking

To enable global remarking of 802.1p, DSCP or both 802.1p and DSCP values:

NVUE Commands

To remark switch priority 0 to egress 802.1p 4

cumulus@switch:~$ nv set qos remark default-global rewrite l2
cumulus@switch:~$ nv set qos remark default-global switch-priority 0 pcp 4
cumulus@switch:~$ nv config apply

To remark switch priority 0 to egress DSCP 22:

cumulus@switch:~$ nv set qos remark default-global rewrite l3
cumulus@switch:~$ nv set qos remark default-global switch-priority 0 dscp 22
cumulus@switch:~$ nv config apply

You can remap multiple switch priority values to the same external 802.1p or DSCP value. For example, to map switch priority 1 and 2 to 802.1p 3:

cumulus@switch:~$ nv set qos remark default-global rewrite l2
cumulus@switch:~$ nv set qos remark default-global switch-priority 1 pcp 3
cumulus@switch:~$ nv set qos remark default-global switch-priority 2 pcp 3
cumulus@switch:~$ nv config apply

To map switch priority 1 and 2 to DSCP 40:

cumulus@switch:~$ nv set qos remark default-global rewrite l3
cumulus@switch:~$ nv set qos remark default-global switch-priority 1 dscp 40
cumulus@switch:~$ nv set qos remark default-global switch-priority 2 dscp 40
cumulus@switch:~$ nv config apply

Linux Commands

In the /etc/cumulus/datapath/qos/qos_features.conf file, modify the traffic.packet_priority_remark_set value to [802.1p], [dscp] or [802.1p,dscp]. For example, to enable the remarking of only 802.1p values:

traffic.packet_priority_remark_set = [802.1p]

You remark 802.1p or DSCP with the priority_remark.8021p or priority_remark.dscp setting. The switch priority (internal cos_) value determines the egress 802.1p or DSCP remarking. For example, to remark switch priority 0 to egress 802.1p 4:

traffic.cos_0.priority_remark.8021p = [4]

To remark switch priority 0 to egress DSCP 22:

traffic.cos_0.priority_remark.dscp = [22]

The # in the configuration file is a comment. The file comments out the traffic.cos_*.priority_remark.8021p and the traffic.cos_*.priority_remark.dscp lines by default. You must uncomment them to set the configuration.

You can remap multiple switch priority values to the same external 802.1p or DSCP value. For example, to map switch priority 1 and 2 to 802.1p 3:

traffic.cos_1.priority_remark.8021p = [3]
traffic.cos_2.priority_remark.8021p = [3]

To map switch priority 1 and 2 to DSCP 40:

traffic.cos_1.priority_remark.dscp = [40]
traffic.cos_2.priority_remark.dscp = [40]

To apply a custom profile to specific interfaces, see Port Groups.

Policy-based Marking

Cumulus Linux supports ACLs through ebtables, iptables or ip6tables for egress packet marking and remarking.

Cumulus Linux uses ebtables to mark layer 2, 802.1p COS values. Cumulus Linux uses iptables to match IPv4 traffic and ip6tables to match IPv6 traffic for DSCP marking.

For more information on configuring and applying ACLs, refer to Access Control List Configuration.

Mark Layer 2 COS

You must use ebtables to match and mark layer 2 bridged traffic. You can match traffic with any supported ebtables rule.

To set the new 802.1p COS value when traffic matches, use -A FORWARD -o <interface> -j setqos --set-cos <value>.

You can only set COS on a per-egress interface basis. Cumulus Linux does not support ebtables based matching on ingress.

The configured action always has the following conditions:

The rule is always part of the FORWARD chain.
The interface (<interface>) is a physical swp port.
The jump action is always setqos (lowercase).
The --set-cos value is a 802.1p COS value between 0 and 7.

For example, to set traffic leaving interface swp5 to 802.1p COS value 4:

-A FORWARD -o swp5 -j setqos --set-cos 4

Mark Layer 3 DSCP

You must use iptables (for IPv4 traffic) or ip6tables (for IPv6 traffic) to match and mark layer 3 traffic.

You can match traffic with any supported iptable or ip6tables rule. To set the new COS or DSCP value when traffic matches, use -A FORWARD -o <interface> -j SETQOS [--set-dscp <value> | --set-cos <value> | --set-dscp-class <name>].

The configured action always has the following conditions:

The rule is always configured as part of the FORWARD chain.
The interface (<interface>) is a physical swp port.
The jump action is always SETQOS (uppercase).

You can configure COS markings with --set-cos and a value between 0 and 7 (inclusive).

You can use only one of --set-dscp or --set-dscp-class.
--set-dscp supports decimal or hex DSCP values between 0 and 77. --set-dscp-class supports standard DSCP naming, described in RFC3260, including ef, be, CS and AF classes.

You can specify either --set-dscp or --set-dscp-class, but not both.

For example, to set traffic leaving interface swp5 to DSCP value 32:

-A FORWARD -o swp5 -j SETQOS --set-dscp 32

To set traffic leaving interface swp11 to DSCP class value CS6:

-A FORWARD -o swp11 -j SETQOS --set-dscp-class cs6

Flow Control

Flow control influences data transmission to manage congestion along a network path.

Cumulus Linux supports the following flow control mechanisms:

Link pause (IEEE 802.3x), sends specialized ethernet frames to an adjacent layer 2 switch to stop or pause all traffic on the link during times of congestion.
Priority Flow Control (PFC), which is an upgrade of link pause that IEEE 802.1bb defines, extends the pause frame concept to act on a per switch priority value basis instead of an entire link. A PFC pause frame indicates to the peer which specific switch priority value to pause, while other switch priority values or queues continue transmitting.

You can not configure link pause and PFC on the same port.

Flow Control Buffers

Before configuring link pause or PFC, configure the buffer pool memory allocated for lossless and lossy flows. The following example sets each to fifty percent:

NVUE Commands

cumulus@switch:~$ nv set qos traffic-pool default-lossless memory-percent 50
cumulus@switch:~$ nv set qos traffic-pool default-lossy memory-percent 50
cumulus@switch:~$ nv config apply

Cumulus Linux allocates 100% of the buffer memory to the default-lossy traffic pool by default. The total memory allocation across pools must not exceed 100%.

Linux Commands

Edit the following lines in the /etc/mlx/datapath/qos/qos_infra.conf file:

Modify the existing ingress_service_pool.0.percent and egress_service_pool.0.percent buffer allocation. Change the existing ingress setting to ingress_service_pool.0.percent = 50. Change the existing egress setting to egress_service_pool.0.percent = 50.
Add the following lines to create a new service_pool, set flow_control to the service pool, and define buffer reservations:

ingress_service_pool.1.percent = 50.0
ingress_service_pool.1.mode = 1
egress_service_pool.1.percent = 50.0
egress_service_pool.1.mode = 1
egress_service_pool.1.infinite_flag = TRUE
#
flow_control.ingress_service_pool = 1
flow_control.egress_service_pool = 1
#
port.service_pool.1.ingress_buffer.reserved = 0
port.service_pool.1.ingress_buffer.dynamic_quota = ALPHA_1
port.service_pool.1.egress_buffer.uc.reserved = 0
port.service_pool.1.egress_buffer.uc.dynamic_quota = ALPHA_INFINITY
#
flow_control.ingress_buffer.dynamic_quota = ALPHA_1
flow_control.egress_buffer.reserved = 0
flow_control.egress_buffer.dynamic_quota = ALPHA_INFINITY

Link Pause

Link pause is an older flow control mechanism that causes all traffic on a link between two switches, or between a host and switch, to stop transmitting during times of congestion. Link pause starts and stops depending on buffer congestion. You configure link pause on a per-direction, per-interface basis. You can receive pause frames to stop the switch from transmitting when requested, send pause frames to request neighboring devices to stop transmitting, or both.

NVIDIA recommends that you use Priority Flow Control (PFC) instead of link pause.
Before configuring link pause, you must first modify the switch buffer allocation. Refer to Flow Control Buffers.

Link pause buffer calculation is a complex topic that IEEE 802.1Q-2012 defines. This attempts to incorporate the delay between signaling congestion and the reception of the signal by the neighboring device. This calculation includes the delay that the PHY and MAC layers (interface delay) introduce as well as the distance between end points (cable length).

Incorrect cable length settings can cause wasted buffer space (triggering congestion too early) or packet drops (congestion occurs before flow control activates).

The following example configuration:

Creates a profile (port group) called my_pause_ports.
Enables sending pause frames and disables receiving pause frames.
Sets the cable length to 50 meters.
Sets link pause on swp1 through swp4, and swp6.

Cumulus Linux also includes frame transmission start and stop threshold, and port buffer settings. NVIDIA recommends that you do not change these settings but, instead, let Cumulus Linux configure the settings dynamically. Only change the threshold and buffer settings if you are an advanced user who understands the buffer configuration requirements for lossless traffic to work seamlessly.

NVUE Commands

cumulus@switch:~$ nv set qos link-pause my_pause_ports tx enable
cumulus@switch:~$ nv set qos link-pause my_pause_ports rx disable
cumulus@switch:~$ nv set qos link-pause my_pause_ports cable-length 50
cumulus@switch:~$ nv set interface swp1-4,swp6 qos link-pause profile my_pause_ports
cumulus@switch:~$ nv config apply

To show the link pause settings for a profile, run the nv show qos link-pause <profile> command

Linux Commands

Uncomment and edit the link_pause section of the /etc/cumulus/datapath/qos/qos_features.conf file.

link_pause.port_group_list = [my_pause_ports]
link_pause.my_pause_ports.port_set = swp1-swp4,swp6
link_pause.my_pause_ports.port_buffer_bytes = 25000
link_pause.my_pause_ports.xoff_size = 10000
link_pause.my_pause_ports.xon_delta = 2000
link_pause.my_pause_ports.rx_enable = false
link_pause.my_pause_ports.tx_enable = true
link_pause.my_pause_ports.cable_length = 10

To process pause frames, you must enable link pause on the specific interfaces.

Priority Flow Control (PFC)

Priority flow control extends the capabilities of link pause by the frames for a specific 802.1p value instead of stopping all traffic on a link. If a switch supports PFC and receives a PFC pause frame for a given 802.1p value, the switch stops transmitting frames from that queue, but continues transmitting frames for other queues.

You use PFC with RDMA over Converged Ethernet - RoCE. The RoCE section provides information to specifically deploy PFC and ECN for RoCE environments.

Before configuring PFC, first modify the switch buffer allocation according to Flow Control Buffers.

PFC buffer calculation is a complex topic defined in IEEE 802.1Q-2012, which attempts to incorporate the delay between signaling congestion and receiving the signal by the neighboring device. This calculation includes the delay that the PHY and MAC layers (called the interface delay) introduce as well as the distance between end points (cable length).
Incorrect cable length settings cause wasted buffer space (triggering congestion too early) or packet drops (congestion occurs before flow control activates).

To apply PFC settings on all ports, modify the default PFC profile (default-global).

The following example modifies the default profile and configures:

PFC on egress queue 0.
Enables sending pause frames and disables receiving pause frames.
The cable length to 50 meters.

NVUE Commands

cumulus@switch:~$ nv set qos pfc default-global switch-priority 0 
cumulus@switch:~$ nv set qos pfc default-global tx enable 
cumulus@switch:~$ nv set qos pfc default-global rx disable 
cumulus@switch:~$ nv set qos pfc default-global cable-length 50
cumulus@switch:~$ nv config apply

To show the PFC settings for the default profile, run the nv show qos pfc default-global command:

cumulus@switch:~$ nv show qos pfc default-global
                   operational  applied  description
-----------------  -----------  -------  --------------------------------
cable-length       50           50       Cable Length (in meters)
port-buffer        25000 B      25000 B  Port Buffer (in bytes)
rx                 disable      disable  PFC Rx State
tx                 enable       enable   PFC Tx State
xoff-threshold     10000 B      10000 B  Xoff Threshold (in bytes)
xon-threshold      2000 B       2000 B   Xon Threshold (in bytes)
[switch-priority]  0            0        Collection of switch priorities.

Linux Commands

Edit the priority flow control section of the /etc/cumulus/datapath/qos/qos_features.conf file.

pfc.port_group_list = [default-global]
pfc.default-global.port_set = allports
pfc.default-global.cos_list = [0]
pfc.default-global.port_buffer_bytes = 25000
pfc.default-global.xoff_size = 10000
pfc.default-global.xon_delta = 2000
pfc.default-global.tx_enable = true
pfc.default-global.rx_enable = false
pfc.default-global.cable_length = 50

To apply a custom profile to specific interfaces, see Port Groups.

PFC Watchdog

PFC watchdog detects and mitigates pause storms on PFC-enabled ports.

In lossless Ethernet, the switch sends PFC PAUSE frames to instruct the link partner to pause sending packets on a traffic class. This back pressure might propagate across the network and, if it persists, can cause the network to stop forwarding traffic. PFC watchdog detects abnormal back pressure caused by receiving an excessive number of pause frames and disables PFC temporarily.

When a lossless queue receives a pause storm from its link partner and the queue is in a paused state for a certain period of time, PFC watchdog mitigates the pause storm. The watchdog stops processing received pause frames on every switch priority corresponding to the traffic class that detects the storm and discards new incoming packets to this egress queue.

The watchdog continues to count pause frames received on the port. If there are no pause frames received in any polling interval period, it restores the PFC configuration on the port and stops dropping packets.

PFC watchdog also detects and mitigates pause storms on link pause-enabled ports. The watchdog configuration for link pause-enabled ports is the same as the configuration for PFC-enabled ports. For a link pause-enabled port, the watchdog stops processing received pause frames on the egress port that detects the storm and discards new incoming packets to all egress queues on the port until congestion diminishes.

PFC watchdog only works for lossless traffic queues.
You can only configure PFC watchdog on a port with PFC (or link pause) configuration.
You can only enable PFC watchdog on a physical interface (swp).
You cannot enable the watchdog on a bond (for example, bond0) but you can enable the watchdog on a port that is a member of a bond (for example, swp1).

To enable PFC watchdog:

NVUE Commands

Enable PFC watchdog on the interfaces where you enable PFC:

cumulus@switch:~$ nv set interface swp1 qos pfc-watchdog
cumulus@switch:~$ nv set interface swp3 qos pfc-watchdog
cumulus@switch:~$ nv config apply

To disable PFC watchdog, run the nv unset interface <interface> qos pfc-watchdog command or the nv set interface <interface> qos pfc-watchdog state disable command.

Linux Commands

Edit the PFC Watchdog Configuration section of the /etc/cumulus/datapath/qos/qos_features.conf file, then reload switchd.

...
# PFC Watchdog Configuration
# Add the port to the port_group_list where you want to enable PFC Watchdog
# It will enable PFC Watchdog on all the traffic-class corresponding to
# the lossless switch-priority configured on the port.
pfc_watchdog.port_group_list = [pfc_wd_port_group]
pfc_watchdog.pfc_wd_port_group.port_set = swp1,swp2
...

cumulus@switch:~$ sudo systemctl reload switchd

You can control the PFC watchdog polling interval and how many polling intervals the PFC watchdog must wait before it mitigates the storm condition. The default polling interval is 100 milliseconds. The default number of polling intervals is 3.

The following example sets the PFC watchdog polling interval to 200 milliseconds and the number of polling intervals to 5:

NVUE Commands

cumulus@switch:~$ nv set qos pfc-watchdog polling-interval 200
cumulus@switch:~$ nv set qos pfc-watchdog robustness 5
cumulus@switch:~$ nv config apply

Linux Commands

Edit the /etc/cumulus/switchd.conf file to set the pfc_wd.poll_interval parameter and the pfc_wd.robustness parameter.

...
# PFC Watchdog poll interval (in msec)
#pfc_wd.poll_interval = 200

# PFC Watchdog robustness (# of iterations)
#pfc_wd.robustness = 5
...

Run the following commands to apply the configuration:

cumulus@switch:~$ echo 5 > /cumulus/switchd/config/pfc_wd/robustness
cumulus@switch:~$ echo 200 > /cumulus/switchd/config/pfc_wd/poll_interval

To show if PFC watchdog is on and to show the status for each traffic class, run the nv show interface <interface> qos pfc-watchdog command:

cumulus@switch:~$ nv show interface swp1 qos pfc-watchdog
                 operational  applied 
---------------  -----------  ------- 
state            enabled      enabled 

PFC WD Status 
=========================== 
    traffic-class  status    deadlock-count 
    -------------  --------  -------------- 

    0              OK        0 
    1              OK        3 
    2              DEADLOCK  2  
    3              OK        0 
    4              OK        0 
    5              OK        0 
    6              OK        0 
    7              DEADLOCK  3

To show PFC watchdog data for a specific traffic class, run the nv show interface <interface> qos pfc-watchdog status <traffic-class> command.

To clear the PFC watchdog deadlock-count on an interface, run the nv action clear interface <interface> qos pfc-watchdog deadlock-count command.

Congestion Control (ECN)

Explicit Congestion Notification (ECN) is an end-to-end layer 3 congestion control protocol. Defined by RFC 3168, ECN relies on bits in the IPv4 header Traffic Class to signal congestion conditions. ECN requires one or both server endpoints to support ECN to be effective.

Instead of telling adjacent devices to stop transmitting during times of buffer congestion, ECN sets the ECN bits of the transit IPv4 or IPv6 header to indicate to end hosts that congestion might occur. As a result, the sending hosts reduce their sending rate until the transit switch no longer sets ECN bits.

You use ECN with RDMA over Converged Ethernet - RoCE. The RoCE section describes how to deploy PFC and ECN for RoCE environments.

ECN operates by having a transit switch that marks packets between two end hosts.

The transmitting host indicates it is ECN-capable by setting the ECN bits in the outgoing IP header to 01 or 10
If the buffer of a transit switch is greater than the configured minimum threshold of the buffer, the switch remarks the ECN bits to 11 indicating Congestion Encountered or CE.
The receiving host marks any reply packets, like a TCP-ACK, as CE (11).
The original transmitting host reduces its transmission rate.
When the switch buffer congestion falls below the configured minimum threshold of the buffer, the switch stops remarking ECN bits, setting them back to 01 or 10.
A receiving host reflects this new ECN marking in the next reply so that the transmitting host resumes sending at normal speeds.

The default profile (default-global) enables ECN by default on egress queue 0 for all ports with the following settings:

A minimum buffer threshold of 150000 bytes. Random ECN marking starts when buffer congestion crosses this threshold. The probability determines if ECN marking occurs.
A maximum buffer threshold of 1500000 bytes. Cumulus Linux marks all ECN-capable packets when buffer congestion crosses this threshold.
A probability of 100 percent that Cumulus Linux marks an ECN-capable packet when buffer congestion is between the minimum threshold and the maximum threshold.
Random Early Detection (RED) disabled. ECN prevents packet drops in the network due to congestion by signaling hosts to transmit less. However, if congestion continues after ECN marking, packets drop after the switch buffer is full. By default, Cumulus Linux tail-drops packets when the buffer is full. You can enable RED to drop packets that are in the queue randomly instead of always dropping the last arriving packet. This might improve overall performance of TCP based flows.

The following example commands change the default ECN profile that applies to all ports. The commands enable ECN on egress queue 4, 5, and 7, set the minimum buffer threshold to 40000 and the maximum buffer threshold to 200000, and enable RED.

NVUE Commands

cumulus@switch:~$ nv set qos congestion-control default-global traffic-class 4,5,7 min-threshold 40000
cumulus@switch:~$ nv set qos congestion-control default-global traffic-class 4,5,7 max-threshold 200000 
cumulus@switch:~$ nv set qos congestion-control default-global traffic-class 4,5,7 red enable
cumulus@switch:~$ nv config apply

The following example disables ECN bit marking in the default profile for all ports.

cumulus@switch:~$ nv set qos congestion-control default-global traffic-class 0 ecn disable
cumulus@switch:~$ nv config apply

To show the ECN settings for the default profile, run the nv show qos congestion-control default-global command:

cumulus@switch:~$ nv show qos congestion-control default-global
    operational  applied  description
--  -----------  -------  -----------

ECN Configurations
=====================
    traffic-class  ECN     RED     Min Th   Max Th    Probability
    -------------  ------  ------  -------  --------  -----------
    4              enable  enable  40000 B  200000 B  100
    5              enable  enable  40000 B  200000 B  100
    7              enable  enable  40000 B  200000 B  100

To show the ECN settings in the default profile for a specific egress queue, run the nv show qos congestion-control default-global traffic-class <value> command:

cumulus@switch:~$ nv show qos congestion-control default-global traffic-class 4 
               operational  applied   description
-------------  -----------  --------  -----------------------------------
ecn            enable       enable    Early Congestion Notification State
max-threshold  200000 B     200000 B  Maximum Threshold (in bytes)
min-threshold  40000 B      40000 B   Minimum Threshold (in bytes)
probability    100          100       Probability
red            enable       enable    Random Early Detection State

Linux Commands

Edit the Explicit Congestion Notification section of the /etc/cumulus/datapath/qos/qos_features.conf file.

default_ecn_red_conf.egress_queue_list = [4,5,7]
default_ecn_red_conf.ecn_enable = true
default_ecn_red_conf.red_enable = true
default_ecn_red_conf.min_threshold_bytes = 40000
default_ecn_red_conf.max_threshold_bytes = 200000
default_ecn_red_conf.probability = 100

To disable ECN bit marking, set ecn_enable to false. The following example disables ECN bit marking in the default profile for all ports.

...
default_ecn_red_conf.ecn_enable = false 
...

To apply a custom ECN profile to specific interfaces, see Port Groups.

Egress Queues

Cumulus Linux supports eight egress queues to provide different classes of service. By default switch priority values map directly to the matching egress queue. For example, switch priority value 0 maps to egress queue 0.

You can remap queues by changing the switch priority value to the corresponding queue value. You can map multiple switch priority values to a single egress queue.

You do not have to assign all egress queues.

The following command examples assign switch priority 2 to egress queue 7:

NVUE Commands

cumulus@switch:~$ nv set qos egress-queue-mapping default-global switch-priority 2 traffic-class 7
cumulus@switch:~$ nv config apply

NVUE only supports the default-global profile.

To show the egress queue mapping configuration for the default profile, run the nv show qos egress-queue-mapping default-global command:

cumulus@switch:~$ nv show qos egress-queue-mapping default-global
    operational  applied  description
--  -----------  -------  -----------

SP->TC mapping configuration
===============================
    switch-priority  traffic-class
    ---------------  -------------
    0                0
    1                1
    2                7
    3                3
    4                4
    5                5
    6                6
    7                7

To show the egress queue mapping for a specific switch priority in the default profile, run the nv show qos egress-queue-mapping default-global switch-priority <value> command. The following example command shows that switch priority 2 maps to egress queue 7.

cumulus@switch:~$ nv show qos egress-queue-mapping default-global switch-priority 2
               operational  applied  description
-------------  -----------  -------  -------------
traffic-class  7            7        Traffic Class

Linux Commands

You configure egress queues in the qos_infra.conf file.

cos_egr_queue.cos_0.uc  = 0
cos_egr_queue.cos_1.uc  = 1
cos_egr_queue.cos_2.uc  = 7
cos_egr_queue.cos_3.uc  = 3
cos_egr_queue.cos_4.uc  = 4
cos_egr_queue.cos_5.uc  = 5
cos_egr_queue.cos_6.uc  = 6
cos_egr_queue.cos_7.uc  = 7

Egress Scheduler

Cumulus Linux supports 802.1Qaz, Enhanced Transmission Selection, which allows the switch to assign bandwidth to egress queues and then schedule the transmission of traffic from each queue. 802.1Qaz supports Priority Queuing.

Cumulus Linux provides a default egress scheduler that applies to all ports, where the bandwidth allocated to egress queues 0,2,4,6 is 12 percent and the bandwidth allocated to egress queues 1,3,5,7 is 13 percent. You can also apply a custom egress scheduler for specific ports; see Port Groups.

The following example modifies the default profile. The commands change the bandwidth allocation for egress queues 0, 1, 5, and 7 to strict, bandwidth allocation for egress queues 2 and 6 to 30 percent and bandwidth allocation for egress queues 3 and 4 to 20 percent.

NVUE Commands

The traffic-class value defines the egress queue where you want to assign bandwidth. For example, traffic-class 2 defines the bandwidth allocation for egress queue 2.
For each egress queue, you can either define the mode as dwrr or strict. In dwrr mode, you must define a bandwidth percent value between 1 and 100. If you do not specify a value for an egress queue, Cumulus Linux uses a DWRR value of 0 (no egress scheduling). The combined total of values you assign to bw_percent must be less than or equal to 100.

cumulus@switch:~$ nv set qos egress-scheduler default-global traffic-class 2,6 mode dwrr 
cumulus@switch:~$ nv set qos egress-scheduler default-global traffic-class 2,6 bw-percent 30 
cumulus@switch:~$ nv set qos egress-scheduler default-global traffic-class 3,4 mode dwrr
cumulus@switch:~$ nv set qos egress-scheduler default-global traffic-class 3,4 bw-percent 20 
cumulus@switch:~$ nv set qos egress-scheduler default-global traffic-class 0,1,5,7 mode strict
cumulus@switch:~$ nv config apply

To show the egress scheduling policy for the default profile, run the nv show qos egress-scheduler default-global command:

cumulus@switch:~$ nv show qos egress-scheduler default-global
    operational  applied  description
--  -----------  -------  -----------

TC->DWRR weight configuration
================================
    traffic-class  mode    bw-percent
    -------------  ------  ----------
    0              strict
    1              strict
    2              dwrr    30
    3              dwrr    20
    4              dwrr    20
    5              strict
    6              dwrr    30
    7              strict

Linux Commands

You configure the egress scheduling policy in the egress scheduling section of the /etc/cumulus/datapath/qos/qos_features.conf file.

The egr_queue_ value defines the egress queue where you want to assign bandwidth. For example, egr_queue_0 defines the bandwidth allocation for egress queue 0.
The bw_percent value defines the bandwidth allocation you want to assign to an egress queue. If you do not specify a value for an egress queue, there is no egress scheduling. If you specify a value of 0 for an egress queue, Cumulus Linux assigns strict priority mode to the egress queue and always processes it ahead of other queues. The combined total of values you assign to bw_percent must be less than or equal to 100.

default_egress_sched.egr_queue_0.bw_percent = 0
default_egress_sched.egr_queue_1.bw_percent = 0
default_egress_sched.egr_queue_2.bw_percent = 30
default_egress_sched.egr_queue_3.bw_percent = 20
default_egress_sched.egr_queue_4.bw_percent = 20
default_egress_sched.egr_queue_5.bw_percent = 0
default_egress_sched.egr_queue_6.bw_percent = 30
default_egress_sched.egr_queue_7.bw_percent = 0

strict mode does not define a maximum bandwidth allocation. This can lead to starvation of other queues.

To apply a custom egress scheduler for specific ports, see Port Groups.

Policing and Shaping

Traffic shaping and policing control the rate at which the switch sends or receives traffic on a network to prevent congestion.

Traffic shaping typically occurs at egress and traffic policing at ingress.

Shaping

Traffic shaping allows a switch to send traffic at an average bitrate lower than the physical interface. Traffic shaping prevents a receiving device from dropping bursty traffic if the device is either not capable of that rate of traffic or has a policer that limits what it accepts.

Traffic shaping works by holding packets in the buffer and releasing them at specific time intervals.

Cumulus Linux supports two levels of hierarchical traffic shaping: one at the egress queue level and one at the port level. This allows for minimum and maximum bandwidth guarantees for each egress queue and a defined port traffic shaping rate.

The following example configuration:

Sets the profile name (port group) to use with the traffic shaping settings to shaper1.
Sets the minimum bandwidth for egress queue 2 to 100 kbps. The default minimum bandwidth is 0 kbps.
Sets the maximum bandwidth for egress queue 2 to 500 kbps. The default minimum bandwidth is 2147483647 kbps.
Sets the maximum packet shaper rate for the port group to 200000. The default maximum packet shaper rate is 2147483647 kbps.
Applies the traffic shaping configuration to swp1, swp2, swp3, and swp5.

When the minimum bandwidth for an egress queue is 0, there is no bandwidth guarantee for this queue.
The maximum bandwidth for an egress queue must not exceed the maximum packet shaper rate for the port group.
The maximum packet shaper rate for the port group must not exceed the physical interface speed.
Cumulus Linux only shapes traffic for the traffic classes in a profile that include shaper configuration.

NVUE Commands

cumulus@switch:~$ nv set qos egress-shaper shaper1 traffic-class 2 min-rate 100
cumulus@switch:~$ nv set qos egress-shaper shaper1 traffic-class 2 max-rate 500
cumulus@switch:~$ nv set qos egress-shaper shaper1 port-max-rate 200000
cumulus@switch:~$ nv set interface swp1-3,swp5 qos egress-shaper profile shaper1
cumulus@switch:~$ nv config apply

Linux Commands

Edit the shaping section of the qos_features.conf file.

Cumulus Linux bases the egr_queue value on the configured egress queue.

shaping.port_group_list = [shaper1]
shaping.shaper1.port_set = swp1-swp3,swp5
shaping.shaper1.egr_queue_0.shaper = [50000, 100000]
shaping.shaper1.port.shaper = 900000

Policing

Traffic policing prevents an interface from receiving more traffic than intended. You use policing to enforce a maximum transmission rate on an interface. The switch drops any traffic above the policing level.

Cumulus Linux supports both a single-rate policer and a dual-rate policer (tricolor policer).

You configure traffic policing using ebtables, iptables, or ip6table rules.

For more information on configuring and applying ACLs, refer to Access Control List Configuration.

Single-rate Policer

To configure a single-rate policer, use iptables JUMP action -j POLICE.

Cumulus Linux supports the following iptable flags with a single-rate policer.

iptables Flag	Description
`--set-mode [pkt \| KB]`	Define the policer to count packets or kilobytes.
`--set-rate [<kbytes> \| <packets>]`	The maximum rate of traffic in kilobytes or packets per second.
`--set-burst <kilobytes>`	The allowed burst size in kilobytes.

For example, to create a policer to allow 400 packets per second with 100 packet burst:
-j POLICE --set-mode pkt --set-rate 400 --set-burst 100

Dual-rate Policer

To configure a dual-rate policer, use the iptables JUMP action -j TRICOLORPOLICE.

Cumulus Linux supports the following iptable flags with a dual-rate policer.

iptables Flag	Description
`--set-color-mode [blind \| aware]`	The policing mode: single-rate (`blind`) or dual-rate (`aware`). The default is `aware`.
`--set-cir <kbps>`	The committed information rate (CIR) in kilobits per second.
`--set-cbs <kbytes>`	The committed burst size (CBS) in kilobytes.
`--set-pir <kbps>`	The peak information rate (PIR) in kilobits per second.
`--set-ebs <kbytes>`	The excess burst size (EBS) in kilobytes.
`--set-conform-action-dscp <dscp value>`	The numerical DSCP value to mark for traffic that conforms to the policer rate.
`--set-exceed-action-dscp <dscp value>`	The numerical DSCP value to mark for traffic that exceeds the policer rate.
`--set-violate-action-dscp <dscp value>`	The numerical DSCP value to mark for traffic that violates the policer rate.
`--set-violate-action [accept \| drop]`	Cumulus Linux either accepts and remarks, or drops packets that violate the policer rate.

For example, to configure a dual-rate, three-color policer, with a 3 Mbps CIR, 500 KB CBS, 10 Mbps PIR, and 1 MB EBS and drops packets that violate the policer:

-j TRICOLORPOLICE --set-color-mode blind --set-cir 3000 --set-cbs 500 --set-pir 10000 --set-ebs 1000 --set-violate-action drop

Port Groups

Cumulus Linux supports profiles (port groups) for all features including ECN and RED. Profiles apply similar QoS configurations to a set of ports.

Configurations with a profile override the global settings for the ingress ports in the port group.
Ports not in a profile use the global settings.
To apply a profile to all ports, use the global profile.

Trust and Marking

You can use port groups to assign different profiles to different ports. A profile is a label for a group of configuration settings.

NVUE Commands

The following example configures two profiles. customer1 applies to swp1, swp4, and swp6. customer2 applies to swp5 and swp7.

cumulus@switch:~$ nv set qos mapping customer1 trust l3 
cumulus@switch:~$ nv set qos mapping customer1 dscp 0 switch-priority 1-7
cumulus@switch:~$ nv set interface swp1,swp4,swp6 qos mapping profile customer1
cumulus@switch:~$ nv set qos mapping customer2 trust l2
cumulus@switch:~$ nv set qos mapping customer2 pcp 1 switch-priority 4 
cumulus@switch:~$ nv set interface swp5,swp7 qos mapping profile customer2
cumulus@switch:~$ nv config apply

The following example configures the profile customports, which assigns traffic on swp1, swp2, and swp3 to switch priority 4 regardless of the ingress marking.

cumulus@switch:~$ nv set qos mapping customports trust port 
cumulus@switch:~$ nv set qos mapping customports port-default-sp 4
cumulus@switch:~$ nv set interface swp1,swp2,swp3 qos mapping profile customports
cumulus@switch:~$ nv config apply

Linux Commands

You define profiles with the source.port_group_list configuration in the qos_features.conf file. A source.port_group_list is one or more names used for a group of settings.

The following example configures two profiles. customer1 applies to swp1, swp4, and swp6. customer2 applies to swp5 and swp7.

source.port_group_list = [customer1,customer2]
source.customer1.packet_priority_source_set = [dscp]
source.customer1.port_set = swp1-swp4,swp6
source.customer1.port_default_priority = 0
source.customer1.cos_0.priority_source.dscp = [0-7]
source.customer2.packet_priority_source_set = [802.1p]
source.customer2.port_set = swp5,swp7
source.customer2.port_default_priority = 0
source.customer2.cos_1.priority_source.8021p = [4]

Configuration	Description
`source.port_group_list`	The names of the port groups (profiles) you want to use. The following example defines `customer1` and `customer2`: `source.port_group_list = [customer1,customer2]`
`source.customer1.packet_priority_source_set`	The ingress marking trust. In the following example, ingress DSCP values are for group `customer1`: `source.customer1.packet_priority_source_set = [dscp]`
`source.customer1.port_set`	The set of ports on which to apply the ingress marking trust policy. In the following example, ports swp1, swp2, swp3, swp4, and swp6 are for `customer1`: `source.customer1.port_set = swp1-swp4,swp6`
`source.customer1.port_default_priority`	The default switch priority marking for unmarked or untrusted traffic. In the following example, Cumulus Linux marks unmarked traffic or layer 2 traffic for `customer1` ports with switch priority 0: `source.customer1.port_default_priority = 0`
`source.customer1.cos_0.priority_source`	The ingress DSCP values to a switch priority value mapping for `customer1`. In the following example, the set of DSCP values from 0 through 7 map to switch priority 0: `source.customer1.cos_0.priority_source.dscp = [0,1,2,3,4,5,6,7]`
`source.customer2.packet_priority_source_set`	The ingress marking trust for `customer2`. In the following example, 802.1p is `trusted`: `source.packet_priority_source_set = [802.1p]`
`source.customer2.port_set`	The set of ports on which to apply the ingress marking trust policy. In the following example, swp5 and swp7 apply for `customer2`: `source.customer2.port_set = swp5,swp7`
`source.customer2.port_default_priority`	The default switch priority marking for unmarked or untrusted traffic. In the following example, Cumulus Linux marks unmarked tagged layer 2 traffic or unmarked VLAN tagged traffic for `customer1` ports with switch priority 0: `source.customer2.port_default_priority = 0`
`source.customer2.cos_0.priority_source`	The switch priority value to an ingress 802.1p value mapping for `customer2`. The following example maps ingress 802.1p value 4 to switch priority 1: `source.customer2.cos_1.priority_source.8021p = [4]`

The following example configures the profile customports, which assigns traffic on swp1, swp2, and swp3 to switch priority 4 regardless of the ingress marking.

source.port_group_list = [customports]
source.customports.packet_priority_source_set = [port]
source.customports.port_default_priority = 4
source.customports.port_set = swp1,swp2,swp3

Remarking

You can use profiles to remark 802.1p or DSCP on egress according to the switch priority (internal COS) value.

To change the marked value on a packet, the switch ASIC reads the enable or disable rewrite flag on the ingress port and refers to the mapping configuration on the egress port to change the marked value. To remark 802.1p or DSCP values, you have to enable the rewrite on the ingress port and configure the mapping on the egress port.

In the following example configuration, only packets that ingress on swp1 and egress on swp2 change the marked value of the packet. Packets that ingress on other ports and egress on swp2 do not change the marked value of the packet. The commands map switch priority 0 and 1 to egress DSCP 37.

NVUE Commands

cumulus@switch:~$ nv set qos remark remark_port_group1 rewrite l3
cumulus@switch:~$ nv set interface swp1 qos remark profile remark_port_group1
cumulus@switch:~$ nv set qos remark remark_port_group2 switch-priority 0 dscp 37
cumulus@switch:~$ nv set qos remark remark_port_group2 switch-priority 1 dscp 37
cumulus@switch:~$ nv set interface swp2 qos remark profile remark_port_group2
cumulus@switch:~$ nv config apply

Linux Commands

You define these profiles with remark.port_group_list in the /etc/cumulus/datapath/qos/qos_features.conf file. The name is a label for configuration settings.

remark.port_group_list = [remark_port_group1,remark_port_group2]
remark.remark_port_group1.packet_priority_remark_set = [dscp]
remark.remark_port_group1.port_set = swp1
remark.remark_port_group2.packet_priority_remark_set = []
remark.remark_port_group2.port_set = swp2
remark.remark_port_group2.cos_0.priority_remark.dscp = [37]
remark.remark_port_group2.cos_1.priority_remark.dscp = [37]

Egress Scheduling

You can use port groups with egress scheduling weights to assign different profiles to different egress ports.

In the following example, the profile list2 applies to swp1, swp3, and swp18. list2 only assigns weights to queues 2, 5, and 6, and schedules the other queues on a best-effort basis when there is no congestion in queues 2, 5, or 6. list1 applies to swp2 and assigns weights to all queues.

NVUE Commands

cumulus@switch:~$ nv set qos egress-scheduler list2 traffic-class 2,5,6 mode dwrr 
cumulus@switch:~$ nv set qos egress-scheduler list2 traffic-class 2,5 bw-percent 50 
cumulus@switch:~$ nv set qos egress-scheduler list2 traffic-class 6 mode strict
cumulus@switch:~$ nv set interface swp1,swp3,swp18 qos egress-scheduler profile list2
cumulus@switch:~$ nv set qos egress-scheduler list1 traffic-class 0,3,4,5,6 mode dwrr 
cumulus@switch:~$ nv set qos egress-scheduler list1 traffic-class 0,3,4,5,6 bw-percent 10 
cumulus@switch:~$ nv set qos egress-scheduler list1 traffic-class 1 mode dwrr
cumulus@switch:~$ nv set qos egress-scheduler list1 traffic-class 1 bw-percent 20 
cumulus@switch:~$ nv set qos egress-scheduler list1 traffic-class 2 mode dwrr
cumulus@switch:~$ nv set qos egress-scheduler list1 traffic-class 2 bw-percent 30 
cumulus@switch:~$ nv set qos egress-scheduler list1 traffic-class 7 mode strict
cumulus@switch:~$ nv set interface swp2 qos egress-scheduler profile list1
cumulus@switch:~$ nv config apply

Linux Commands

You define port groups with egress_sched.port_group_list in the /etc/cumulus/datapath/qos/qos_features.conf file. An egress_sched.port_group_list includes the names for the group settings. The name is a label (profile) for the configuration settings.

egress_sched.port_group_list = [list1,list2]
egress_sched.list1.port_set = swp2
egress_sched.list1.egr_queue_0.bw_percent = 10
egress_sched.list1.egr_queue_1.bw_percent = 20
egress_sched.list1.egr_queue_2.bw_percent = 30
egress_sched.list1.egr_queue_3.bw_percent = 10
egress_sched.list1.egr_queue_4.bw_percent = 10
egress_sched.list1.egr_queue_5.bw_percent = 10
egress_sched.list1.egr_queue_6.bw_percent = 10
egress_sched.list1.egr_queue_7.bw_percent = 0
#
egress_sched.list2.port_set = [swp1,swp3,swp18]
egress_sched.list2.egr_queue_2.bw_percent = 50
egress_sched.list2.egr_queue_5.bw_percent = 50
egress_sched.list2.egr_queue_6.bw_percent = 0

Configuration	Description
`egress_sched.port_group_list`	The names of the port groups (labels) to use. The following example defines port groups list1 snd list2: `egress_sched.port_group_list = [list1,list2]`
`egress_sched.list1.port_set`	The interfaces on which you want to apply the port group. `egress_sched.list1.port_set = swp2`
`egress_sched.list1.egr_queue_0.bw_percent`	The percentage of bandwidth for egress queue 0. `egress_sched.list1.egr_queue_0.bw_percent = 10`
`egress_sched.list1.egr_queue_1.bw_percent`	The percentage of bandwidth for egress queue 1. `egress_sched.list1.egr_queue_1.bw_percent = 20`
`egress_sched.list1.egr_queue_2.bw_percent`	The percentage of bandwidth for egress queue 2. `egress_sched.list1.egr_queue_2.bw_percent = 30`
`egress_sched.list1.egr_queue_3.bw_percent`	The percentage of bandwidth for egress queue 3. `egress_sched.list1.egr_queue_3.bw_percent = 10`
`egress_sched.list1.egr_queue_4.bw_percent`	The percentage of bandwidth for egress queue 4. `egress_sched.list1.egr_queue_4.bw_percent = 10`
`egress_sched.list1.egr_queue_5.bw_percent`	The percentage of bandwidth for egress queue 5. `egress_sched.list1.egr_queue_5.bw_percent = 10`
`egress_sched.list1.egr_queue_6.bw_percent`	The percentage of bandwidth for egress queue 6. `egress_sched.list1.egr_queue_6.bw_percent = 10`
`egress_sched.list1.egr_queue_7.bw_percent`	The percentage of bandwidth for egress queue 7. `0` indicates a strict priority queue: `egress_sched.list1.egr_queue_7.bw_percent = 0`
`egress_sched.list2.port_set`	The interfaces you want to apply to the port group. The following example applies `swp1`, `swp3` and `swp18` to port group `list2`: `egress_sched.list2.port_set = [swp1,swp3,swp18]`
`egress_sched.list2.egr_queue_2.bw_percent`	The percentage of bandwidth for egress queue 2. `egress_sched.list2.egr_queue_2.bw_percent = 50`
`egress_sched.list2.egr_queue_5.bw_percent`	The percentage of bandwidth for egress queue 5. `egress_sched.list2.egr_queue_5.bw_percent = 50`
`egress_sched.list2.egr_queue_6.bw_percent`	The percentage of bandwidth for egress queue 6. `0` indicates a strict priority queue: `egress_sched.list2.egr_queue_6.bw_percent = 0`

PFC

To set priority flow control on a group of ports, you create a profile to define the egress queues that support sending PFC pause frames and define the set of interfaces to which you want to apply PFC pause frame configuration. Cumulus Linux automatically enables PFC frame transmit and PFC frame receive, and derives all other PFC settings, such as the buffer limits that trigger PFC frames transmit to start and stop, the amount of reserved buffer space, and the cable length.

NVUE Commands

The following example applies a PFC profile called my_pfc_ports for egress queue 3 and 5 on swp1, swp2, swp3, swp4, and swp6.

cumulus@switch:~$ nv set qos pfc my_pfc_ports switch-priority 3,5
cumulus@switch:~$ nv set interface swp1-4,swp6 qos pfc profile my_pfc_ports
cumulus@switch:~$ nv config apply

The following example applies a PFC profile called my_pfc_ports2 for egress queue 0 on swp1. The commands disable PFC frame receive, and set the buffer limit that triggers PFC frame transmission to stop to 1500 bytes and to start to 1000 bytes. The commands also set the amount of reserved buffer space to 2000 bytes, and the cable length to 50 meters:

cumulus@switch:~$ nv set qos pfc my_pfc_ports2 switch-priority 0 
cumulus@switch:~$ nv set qos pfc my_pfc_ports2 xoff-threshold 1500 
cumulus@switch:~$ nv set qos pfc my_pfc_ports2 xon-threshold 1000 
cumulus@switch:~$ nv set qos pfc my_pfc_ports2 tx enable 
cumulus@switch:~$ nv set qos pfc my_pfc_ports2 rx disable 
cumulus@switch:~$ nv set qos pfc my_pfc_ports2 port-buffer 2000 
cumulus@switch:~$ nv set qos pfc my_pfc_ports2 cable-length 50
cumulus@switch:~$ nv set interface swp1 qos pfc profile my_pfc_ports2
cumulus@switch:~$ nv config apply

All PFC commands

Command	Description
`nv set qos pfc <profile> port-buffer <value>`	The amount of reserved buffer space (from the global shared buffer) for the interfaces defined in the port group list . The following example sets the amount of reserved buffer space to 25000 bytes: `nv set qos pfc my_pfc_ports port-buffer 25000`
`nv set qos pfc <profile> xoff-threshold <value>`	The amount of reserved buffer that the switch must consume before sending a PFC pause frame out of the set of interfaces in the port group list. The following example sends PFC pause frames after consuming 20000 bytes of reserved buffer: `nv set qos pfc my_pfc_ports xoff-threshold 20000`
`nv set qos pfc <profile> xon-threshold <value>`	The number of bytes below the `xoff` threshold that the buffer consumption must drop below before sending PFC pause frames stops. In the following example, the buffer congestion must reduce by 1000 bytes (to 8000 bytes) before PFC pause frames stop: `nv set qos pfc my_pfc_ports xon-threshold 1000`
`nv set qos pfc <profile> rx enable` `nv set qos pfc <profile> rx disable`	Enables or disables sending PFC pause frames. The default value is enable. The following example disables sending PFC pause frames: `nv set qos pfc my_pfc_ports rx disable`
`nv set qos pfc <profile> tx enable` `nv set qos pfc <profile> tx disable`	Enables or disables receiving PFC pause frames. You do not need to define the COS values for `rx enable`. The switch receives any COS value. The default value is enable. The following example disables receiving PFC pause frames: `nv set qos pfc my_pfc_ports tx disable`
`nv set qos pfc <profile> cable-length <value>`	The length, in meters, of the cable that attaches to the ports. Cumulus Linux uses this value internally to determine the latency between generating a PFC pause frame and receiving the PFC pause frame. The default is `10` meters. The following example sets the cable length to `5` meters: `nv set qos pfc my_pfc_ports cable-length 5`

Linux Commands

Edit the priority flow control section of the /etc/cumulus/datapath/qos/qos_features.conf file.

The following example applies a PFC profile called my_pfc_ports for egress queue 3 and 5 on swp1, swp2, swp3, swp4, and swp6.

pfc.port_group_list = [my_pfc_ports2]
pfc.my_pfc_ports2.cos_list = [0]
pfc.my_pfc_ports2.port_set = swp1

The following example applies a PFC profile called my_pfc_ports2 for egress queue 0 on swp1. The commands also disable PFC frame receive, and set the xoff-size to 1500 bytes, the xon-size to 1000 bytes, the headroom to 2000 bytes, and the cable length to 10 meters:

pfc.port_group_list = [my_pfc_ports2]
pfc.my_pfc_ports2.cos_list = [0]
pfc.my_pfc_ports2.port_set = swp1
pfc.my_pfc_ports2.port_buffer_bytes = 2000
pfc.my_pfc_ports2.xoff_size = 1500
pfc.my_pfc_ports2.xon_delta = 1000
pfc.my_pfc_ports2.tx_enable = true
pfc.my_pfc_ports2.rx_enable = false
pfc.my_pfc_ports2.cable_length = 10

All PFC configuration options

Configuration	Description
`pfc.my_pfc_ports.port_buffer_bytes`	The amount of reserved buffer space (from the global shared buffer) for the interfaces defined in the port group list. The following example sets the amount of reserved buffer space to 25000 bytes: `pfc.my_pfc_ports.port_buffer_bytes = 25000`
`pfc.my_pfc_ports.xoff_size`	The amount of reserved buffer that the switch must consume before sending a PFC pause frame out the set of interfaces in the port group list. The following example sends PFC pause frames after consuming 10000 bytes of reserved buffer: `pfc.my_pfc_ports.xoff_size = 10000`
`pfc.my_pfc_ports.xon_delta`	The number of bytes below the `xoff` threshold that the buffer consumption must drop below before sending PFC pause frames stops. The following example the buffer congestion must reduce by 2000 bytes (to 8000 bytes) before PFC pause frames stop: `pfc.my_pfc_ports.xon_delta = 2000`
`pfc.my_pfc_ports.rx_enable`	Enables (`true`) or disables (`false`) sending PFC pause frames. The default value is `true`. The following example enables sending PFC pause frames: `pfc.my_pfc_ports.tx_enable = true`
`pfc.my_pfc_ports.tx_enable`	Enables (`true`) or disables (`false`) receiving PFC pause frames. You do not need to define the COS values for `rx_enable`. The switch receives any COS value. The default value is `true`. The following example enables receiving PFC pause frames: `pfc.my_pfc_ports.rx_enable = true`
`pfc.my_pfc_ports.cable_length`	The length, in meters, of the cable that attaches to the port in the port group list. Cumulus Linux uses this value internally to determine the latency between generating a PFC pause frame and receiving the PFC pause frame. The default is `10` meters In this example, the cable is `5` meters: `pfc.my_pfc_ports.cable_length = 5`

ECN

You can create ECN profiles and assign them to different ports.

NVUE Commands

The following example creates a custom ECN profile called my-red-profile for egress queue (traffic-class) 1 and 2. The commands set the minimum buffer threshold to 40000 bytes, maximum buffer threshold to 200000 bytes, and the probability to 10. The commands also enable RED and apply the ECN profile to swp1 and swp2.

cumulus@switch:~$ nv set qos congestion-control my-red-profile traffic-class 1,2 min-threshold-bytes 40000 
cumulus@switch:~$ nv set qos congestion-control my-red-profile traffic-class 1,2 max-threshold-bytes 200000 
cumulus@switch:~$ nv set qos congestion-control my-red-profile traffic-class 1,2 probability 10
cumulus@switch:~$ nv set qos congestion-control my-red-profile traffic-class 1,2 red enable
cumulus@switch:~$ nv set interface swp1,swp2 qos congestion-control my-red-profile
cumulus@switch:~$ nv config apply

You can configure different thresholds and probability values for different traffic classes in a custom profile:

cumulus@switch:~$ nv set qos congestion-control my-red-profile traffic-class 1,2 min-threshold-bytes 40000 
cumulus@switch:~$ nv set qos congestion-control my-red-profile traffic-class 1,2 max-threshold-bytes 200000 
cumulus@switch:~$ nv set qos congestion-control my-red-profile traffic-class 1,2 probability 10
cumulus@switch:~$ nv set qos congestion-control my-red-profile traffic-class 1,2 red enable
cumulus@switch:~$ nv set qos congestion-control my-red-profile traffic-class 4 min-threshold-bytes 30000 
cumulus@switch:~$ nv set qos congestion-control my-red-profile traffic-class 4 max-threshold-bytes 150000 
cumulus@switch:~$ nv set qos congestion-control my-red-profile traffic-class 4 probability 80
cumulus@switch:~$ nv set interface swp1,swp2 qos congestion-control my-red-profile
cumulus@switch:~$ nv config apply

You can disable ECN bit marking for an ECN profile. The following example disables ECN bit marking in the my-red-profile profile:

cumulus@switch:~$ nv set qos congestion-control my-red-profile traffic-class 1 ecn disable
cumulus@switch:~$ nv config apply

Linux Commands

Edit the Explicit Congestion Notification section of the /etc/cumulus/datapath/qos/qos_features.conf file.

The following example creates a custom ECN profile called my-red-profile for egress queue 1 and 2, with a minimum buffer threshold of 40000 bytes, maximum buffer threshold of 200000 bytes, and a probability of 10. The commands also enable RED and apply the ECN profile to swp1 and swp2.

ecn_red.port_group_list = [my-red-profile] 
my-red-profile.egress_queue_list = [1,2]
my-red-profile.port_set = swp1,swp2
my-red-profile.ecn_enable = true
my-red-profile.red_enable = true
my-red-profile.min_threshold_bytes = 40000
my-red-profile.max_threshold_bytes = 200000
my-red-profile.probability = 10

To disable ECN bit marking, set ecn_enable to false. The following example disables ECN bit marking in the my-red-profile.

...
my-red-profile.ecn_enable = false 
...

Traffic Pools

Cumulus Linux supports adjusting the following traffic pools:

Traffic Pool	Description
`default-lossy`	The default traffic pool for all switch priorities.
`default-lossless`	The traffic pool for lossless traffic when you enable flow control.
`mc-lossy`	The traffic pool for multicast traffic.
`roce-lossy`	The traffic pool for RoCE lossy mode.
`roce-lossless`	The traffic pool for RoCE lossless mode.

You can only have a single lossless pool configured on the switch at a time. Configure the roce-lossless pool when you are using RoCE, otherwise configure the default-lossless pool.
You can configure multiple lossy pools concurrently.

You configure a traffic pool by associating switch priorities and defining the buffer memory percentages allocated to the pools. The following example associates switch priority 2 and allocates a memory percentage of 30 for the mc-lossy pool:

NVUE Commands

cumulus@switch:~$ nv set qos traffic-pool default-lossy switch-priority 0,1,3,4,5,6,7
cumulus@switch:~$ nv set qos traffic-pool default-lossy memory-percent 70
cumulus@switch:~$ nv set qos traffic-pool mc-lossy switch-priority 2
cumulus@switch:~$ nv set qos traffic-pool mc-lossy memory-percent 30
cumulus@switch:~$ nv config apply

Linux Commands

Configure the following settings in the /etc/mlx/datapath/qos/qos_infra.conf file:

traffic.priority_group_list = [service2,bulk]

priority_group.service2.cos_list = [2]
priority_group.bulk.cos_list = [0,1,3,4,5,6,7]

priority_group.service2.id = 2

priority_group.service2.service_pool = 2

ingress_service_pool.2.percent = 30
ingress_service_pool.0.percent = 70

port.service_pool.2.ingress_buffer.reserved = 10240

ingress_service_pool.2.mode = 1

port.service_pool.2.ingress_buffer.dynamic_quota = ALPHA_8

priority_group.service2.ingress_buffer.dynamic_quota = ALPHA_8

egress_buffer.egr_queue_2.uc.service_pool = 2

egress_service_pool.2.percent = 30
egress_service_pool.0.percent = 70

port.service_pool.2.egress_buffer.uc.reserved = 0

egress_buffer.cos_2.mc.service_pool = 2

egress_buffer.egr_queue_2.uc.reserved = 1024

port.egress_buffer.mc.reserved = 10240
port.egress_buffer.mc.shared_size = 2097152
egress_service_pool.2.mode = 1

port.service_pool.2.egress_buffer.uc.dynamic_quota = ALPHA_8

egress_buffer.egr_queue_2.uc.dynamic_quota = ALPHA_8

egress_buffer.cos_2.mc.dynamic_quota = ALPHA_8

For additional default-lossless and RoCE pool examples, see Flow Control Buffers and RoCE. You can view traffic-pool configuration with the nv show qos traffic-pool <pool name> command:

cumulus@switch:~$  nv show qos traffic-pool default-lossy
                   applied
-----------------  -------
memory-percent     80     
[switch-priority]  0      
[switch-priority]  1      
[switch-priority]  2      
[switch-priority]  3      
[switch-priority]  4      
[switch-priority]  5      
[switch-priority]  6      
[switch-priority]  7

Advanced Buffer Tuning

You can use NVUE commands to tune advanced buffer properties in addition to the supported traffic pool configurations. Advanced buffer configuration can override the base traffic-pool profiles configured on the system.

You can only configure advanced buffer settings for the default-global profile.

Buffer Regions

You can adjust advanced buffer settings with the following NVUE command:

nv set qos advance-buffer-config default-global <buffer> <priority-group | property> <value>

You can adjust settings for the following supported buffer regions and properties:

Buffers	Supported Property Values
`ingress-lossy-buffer`	Cumulus Linux supports the following properties for the `bulk`, `control`, and `service[1-6]` priority groups: `name` - The priority group alias name. `reserved` - The reserved buffer allocation in bytes. `service-pool` - Service pool mapping. `shared-alpha` - The dynamic shared buffer alpha allocation. `shared-bytes` - The static shared buffer allocation in bytes. `switch-priority` - Switch priority values.
`egress-lossless-buffer`	`reserved` - The reserved buffer allocation in bytes. `service-pool` - Service pool mapping. `shared-alpha` - The dynamic shared buffer alpha allocation. `shared-bytes` - The static shared buffer allocation in bytes.
`ingress-lossless-buffer`	`service-pool` - Service pool mapping. `shared-alpha` - The dynamic shared buffer alpha allocation. `shared-bytes` - The static shared buffer allocation in bytes.
`egress-lossy-buffer`	`multicast-port` - Multicast port `reserved` or `shared-bytes` allocation in bytes. `multicast-switch-priority [0-7]` - Set the `reserved`, `service-pool`,`shared-alpha`, or `shared-bytes` properties for each multicast switch priority. `traffic-class [0-15]` - Set the `reserved`, `service-pool`,`shared-alpha`, or `shared-bytes` properties for each traffic class.

Configure shared-bytes for buffer regions mapped to static service pools, and shared-alpha for buffer regions mapped to dynamic service pools.

The shared buffer alpha value determines the proportion of available shared memory allocated across buffer regions. Regions with higher alpha values receive a higher proportion of available shared buffer memory. The following example changes the ingress-lossless-buffer shared alpha value to alpha_2 when using RoCE lossless mode:

cumulus@switch:~$ nv set qos advance-buffer-config default-global ingress-lossless-buffer shared-alpha alpha_2
cumulus@switch:~$ nv config apply

Service Pools

You can configure ingress and egress service pool profile properties with the following NVUE commands:

nv set qos advance-buffer-config default-global ingress-pool <pool-id> <property> <value>
nv set qos advance-buffer-config default-global egress-pool <pool-id> <property> <value>

You can adjust the following properties for each pool:

Property	Description
`infinite`	The pool infinite flag.
`memory-percent`	The pool memory percent allocation.
`mode`	The pool mode: static or dynamic.
`reserved`	The reserved buffer allocation in bytes.
`shared-alpha`	The dynamic shared buffer alpha allocation.
`shared-bytes`	The static shared buffer allocation in bytes.

A relationship exists between the default traffic pools and the advanced buffer configuration settings.

Use caution when configuring advanced buffer settings. NVUE presents a warning if you attempt to apply incompatible traffic pool and advanced buffer configurations. NVUE performs the following validation checks before applying advanced buffer configurations:

You must map all switch priorities (0-7) to a priority group. You can map more than one switch priority to the same priority group.
The sum of memory-percent values across all ingress pools must be less than or equal to 100 percent.
The sum of memory-percent values across all egress pools must be less than or equal to 100 percent.

Reference the table below to view the mappings between the default traffic pool and advanced buffer properties:

Default Traffic Pool	Default Traffic Pool Properties	Advanced Buffer Region or Service Pool	Advanced Buffer Properties
`default-lossy`	`memory-percent`	`ingress-pool 0` `egress-pool 0`	`memory-percent`
`default-lossy`	`switch-priority`	`ingress-lossy-buffer`	`priority-group bulk switch-priority`
`default-lossless`	`memory-percent`	`ingress-pool 1` `egress-pool 1`	`memory-percent`
`roce-lossless`	`memory-percent`	`ingress-pool 1` `egress-pool 1`	`memory-percent`
`mc-lossy`	`memory-percent`	`ingress-pool 2` `egress-pool 2`	`memory-percent`
`mc-lossy`	`switch-priority`	`ingress-lossy-buffer`	`priority-group service2 switch-priority`

For example, to assign 20 percent of memory to a new static service pool, you must allow 20 percent of memory to be available from the default traffic pools. The following commands reduce the default-lossy traffic pool to 80 percent memory, allowing you to assign the memory to ingress-pool 3:

cumulus@switch:~$ nv set qos traffic-pool default-lossy memory-percent 80
cumulus@switch:~$ nv set qos advance-buffer-config default-global ingress-pool 3 memory-percent 20
cumulus@switch:~$ nv config apply

You can view advanced buffer configuration with the nv show qos advance-buffer-config default-global <buffer/pool name> command:

cumulus@switch:~$ nv show qos advance-buffer-config default-global ingress-pool
Pool-Id  infinite  memory-percent  mode     reserved  shared-alpha  shared-bytes
-------  --------  --------------  -------  --------  ------------  ------------
0                  80              dynamic                                      
3                  20

Syntax Checker

Cumulus Linux provides a syntax checker for the qos_features.conf and qos_infra.conf files to check for errors, such missing parameters or invalid parameter labels and values.

The syntax checker runs automatically with every switchd reload.

You can run the syntax checker manually from the command line with the cl-consistency-check --datapath-syntax-check command. If errors exist, they write to stderr by default. If you run the command with -q, errors write to the /var/log/switchd.log file.

The cl-consistency-check --datapath-syntax-check command takes the following options:

Option	Description
`-h`	Displays this list of command options.
`-q`	Runs the command in quiet mode. Errors write to the `/var/log/switchd.log` file instead of `stderr`.
`-qi`	Runs the syntax checker against a specified `qos_infra.conf` file.
`-qf`	Runs the syntax checker against a specified `qos_features.conf` file.

By default the syntax checker assumes:

qos_infra.conf is in /etc/mlx/datapath/qos/qos_infra.conf
qos_features.conf is in /etc/cumulus/datapath/qos/qos_features.conf

You can run the syntax checker when switchd is either running or stopped.

Show Qos Counters

NVUE provides the following commands to show QoS statistics for an interface:

NVUE Command	Description
`nv show interface <interface> counters qos`	Shows all QoS statistics for a specific interface.
`nv show interface <interface> counters qos egress-queue-stats`	Shows QoS egress queue statistics for a specific interface.
`nv show interface <interface> counters qos ingress-buffer-stats`	Shows QoS ingress buffer statistics for a specific interface.
`nv show interface <interface> counters qos pfc-stats`	Shows QoS PFC statistics for a specific interface.
`nv show interface <interface> counters qos port-stats`	Shows QoS port statistics for a specific interface.

The following example shows all QoS statistics for swp1:

cumulus@switch:~$ nv show interface swp1 counters qos
Ingress Buffer Statistics
============================
    priority-group  rx-frames  rx-buffer-discards  rx-shared-buffer-discards
    --------------  ---------  ------------------  -------------------------
    0               0          0 Bytes             0 Bytes                  
    1               0          0 Bytes             0 Bytes                  
    2               0          0 Bytes             0 Bytes                  
    3               0          0 Bytes             0 Bytes                  
    4               0          0 Bytes             0 Bytes                  
    5               0          0 Bytes             0 Bytes                  
    6               0          0 Bytes             0 Bytes                  
    7               0          0 Bytes             0 Bytes                  

Egress Queue Statistics
==========================
    traffic-class  tx-frames  tx-bytes  tx-uc-buffer-discards  wred-discards
    -------------  ---------  --------  ---------------------  -------------
    0              0          0 Bytes   0 Bytes                0            
    1              0          0 Bytes   0 Bytes                0            
    2              0          0 Bytes   0 Bytes                0            
    3              0          0 Bytes   0 Bytes                0            
    4              0          0 Bytes   0 Bytes                0            
    5              0          0 Bytes   0 Bytes                0            
    6              0          0 Bytes   0 Bytes                0            
    7              0          0 Bytes   0 Bytes                0            

PFC Statistics
=================
    switch-priority  rx-pause-frames  rx-pause-duration  tx-pause-frames  tx-pause-duration
    ---------------  ---------------  -----------------  ---------------  -----------------
    0                0                0                  0                0                
    1                0                0                  0                0                
    2                0                0                  0                0                
    3                0                0                  0                0                
    4                0                0                  0                0                
    5                0                0                  0                0                
    6                0                0                  0                0                
    7                0                0                  0                0                

Qos Port Statistics
======================
    Counter             Receive  Transmit
    ------------------  -------  --------
    ecn-marked-packets  n/a      0       
    mc-buffer-discards  n/a      0       
    pause-frames        0        0
...

Clear QoS Buffers

To clear the Qos pool buffers, run the nv action clear qos buffer pool command.
To clear the QoS multicast switch priority buffers, run the nv action clear qos buffer multicast-switch-priority command.
To clear the Qos buffers on an interface, run the nv action clear interface <interface> qos buffer command.

cumulus@switch:~$ nv action clear qos buffer pool
QoS pool buffers cleared.
Action succeeded

cumulus@switch:~$ nv action clear qos buffer multicast-switch-priority
QoS multicast buffers cleared.
Action succeeded

cumulus@switch:~$ nv action clear interface swp1 qos buffer
QoS buffers cleared on swp1.
Action succeeded

Default Configuration Files

qos_features.conf

# /etc/cumulus/datapath/qos/qos_features.conf
#
# Copyright © 2021 NVIDIA CORPORATION & AFFILIATES. ALL RIGHTS RESERVED.
#
# This software product is a proprietary product of Nvidia Corporation and its affiliates
# (the "Company") and all right, title, and interest in and to the software
# product, including all associated intellectual property rights, are and
# shall remain exclusively with the Company.
#
# This software product is governed by the End User License Agreement
# provided with the software product. 

# packet header field used to determine the packet priority level
# fields include {802.1p, dscp, port}
traffic.packet_priority_source_set = [802.1p]
traffic.port_default_priority      = 0

# packet priority source values assigned to each internal cos value
# internal cos values {cos_0..cos_7}
# (internal cos 3 has been reserved for CPU-generated traffic)
# 802.1p values = {0..7}
traffic.cos_0.priority_source.8021p = [0]
traffic.cos_1.priority_source.8021p = [1]
traffic.cos_2.priority_source.8021p = [2]
traffic.cos_3.priority_source.8021p = [3]
traffic.cos_4.priority_source.8021p = [4]
traffic.cos_5.priority_source.8021p = [5]
traffic.cos_6.priority_source.8021p = [6]
traffic.cos_7.priority_source.8021p = [7]

# dscp values = {0..63}
#traffic.cos_0.priority_source.dscp = [0,1,2,3,4,5,6,7]
#traffic.cos_1.priority_source.dscp = [8,9,10,11,12,13,14,15]
#traffic.cos_2.priority_source.dscp = [16,17,18,19,20,21,22,23]
#traffic.cos_3.priority_source.dscp = [24,25,26,27,28,29,30,31]
#traffic.cos_4.priority_source.dscp = [32,33,34,35,36,37,38,39]
#traffic.cos_5.priority_source.dscp = [40,41,42,43,44,45,46,47]
#traffic.cos_6.priority_source.dscp = [48,49,50,51,52,53,54,55]
#traffic.cos_7.priority_source.dscp = [56,57,58,59,60,61,62,63]
# remark packet priority value
# fields include {802.1p, dscp}
traffic.packet_priority_remark_set = []

# packet priority remark values assigned from each internal cos value
# internal cos values {cos_0..cos_7}
# (internal cos 3 has been reserved for CPU-generated traffic)
# 802.1p values = {0..7}
#traffic.cos_0.priority_remark.8021p = [0]
#traffic.cos_1.priority_remark.8021p = [1]
#traffic.cos_2.priority_remark.8021p = [2]
#traffic.cos_3.priority_remark.8021p = [3]
#traffic.cos_4.priority_remark.8021p = [4]
#traffic.cos_5.priority_remark.8021p = [5]
#traffic.cos_6.priority_remark.8021p = [6]
#traffic.cos_7.priority_remark.8021p = [7]

# dscp values = {0..63}
#traffic.cos_0.priority_remark.dscp = [0]
#traffic.cos_1.priority_remark.dscp = [8]
#traffic.cos_2.priority_remark.dscp = [16]
#traffic.cos_3.priority_remark.dscp = [24]
#traffic.cos_4.priority_remark.dscp = [32]
#traffic.cos_5.priority_remark.dscp = [40]
#traffic.cos_6.priority_remark.dscp = [48]
#traffic.cos_7.priority_remark.dscp = [56]

# source.port_group_list = [source_port_group]
# source.source_port_group.packet_priority_source_set = [dscp]
# source.source_port_group.port_set = swp1-swp4,swp6
# source.source_port_group.port_default_priority = 0
# source.source_port_group.cos_0.priority_source.dscp = [0,1,2,3,4,5,6,7]
# source.source_port_group.cos_1.priority_source.dscp = [8,9,10,11,12,13,14,15]
# source.source_port_group.cos_2.priority_source.dscp = [16,17,18,19,20,21,22,23]
# source.source_port_group.cos_3.priority_source.dscp = [24,25,26,27,28,29,30,31]
# source.source_port_group.cos_4.priority_source.dscp = [32,33,34,35,36,37,38,39]
# source.source_port_group.cos_5.priority_source.dscp = [40,41,42,43,44,45,46,47]
# source.source_port_group.cos_6.priority_source.dscp = [48,49,50,51,52,53,54,55]
# source.source_port_group.cos_7.priority_source.dscp = [56,57,58,59,60,61,62,63]

# remark.port_group_list = [remark_port_group]
# remark.remark_port_group.packet_priority_remark_set = [dscp]
# remark.remark_port_group.port_set = swp1-swp4,swp6
# remark.remark_port_group.cos_0.priority_remark.dscp = [0]
# remark.remark_port_group.cos_1.priority_remark.dscp = [8]
# remark.remark_port_group.cos_2.priority_remark.dscp = [16]
# remark.remark_port_group.cos_3.priority_remark.dscp = [24]
# remark.remark_port_group.cos_4.priority_remark.dscp = [32]
# remark.remark_port_group.cos_5.priority_remark.dscp = [40]
# remark.remark_port_group.cos_6.priority_remark.dscp = [48]
# remark.remark_port_group.cos_7.priority_remark.dscp = [56]

# to configure priority flow control on a group of ports:
# -- assign cos value(s) to the cos list
# -- add or replace a port group names in the port group list
# -- for each port group in the list
#    -- populate the port set, e.g.
#       swp1-swp4,swp8,swp50s0-swp50s3
#    -- set a PFC buffer size in bytes for each port in the group
#    -- set the xoff byte limit (buffer limit that triggers PFC frames transmit to start)
#    -- set the xon byte delta (buffer limit that triggers PFC frames transmit to stop)
#    -- enable PFC frame transmit and/or PFC frame receive

# priority flow control
#pfc.port_group_list = [pfc_port_group]
#pfc.pfc_port_group.cos_list = []
#pfc.pfc_port_group.port_set = swp1-swp4,swp6
#pfc.pfc_port_group.port_buffer_bytes = 25000
#pfc.pfc_port_group.xoff_size = 10000
#pfc.pfc_port_group.xon_delta = 2000
#pfc.pfc_port_group.tx_enable = true
#pfc.pfc_port_group.rx_enable = true
#Specify cable length in mts
#pfc.pfc_port_group.cable_length = 10

# to configure pause on a group of ports:
# -- add or replace port group names in the port group list
# -- for each port group in the list
#    -- populate the port set, e.g.
#       swp1-swp4,swp8,swp50s0-swp50s3
#    -- set a pause buffer size in bytes for each port
#    -- set the xoff byte limit (buffer limit that triggers pause frames transmit to start)
#    -- set the xon byte delta (buffer limit that triggers pause frames transmit to stop)
#    -- enable pause frame transmit and/or pause frame receive

# link pause
# link_pause.port_group_list = [pause_port_group]
# link_pause.pause_port_group.port_set = swp1-swp4,swp6
# link_pause.pause_port_group.port_buffer_bytes = 25000
# link_pause.pause_port_group.xoff_size = 10000
# link_pause.pause_port_group.xon_delta = 2000
# link_pause.pause_port_group.rx_enable = true
# link_pause.pause_port_group.tx_enable = true
# Specify cable length in mts
# link_pause.pause_port_group.cable_length = 10

# Explicit Congestion Notification
# to configure ECN and RED on a group of ports:
# -- add or replace port group names in the port group list
# -- assign cos value(s) to the cos list
# -- for each port group in the list
#    -- populate the port set, e.g.
#       swp1-swp4,swp8,swp50s0-swp50s3
# -- to enable RED requires the latest traffic.conf
#Default ECN configuration on TC0
default_ecn_red_conf.egress_queue_list = [0]
default_ecn_red_conf.ecn_enable = true
default_ecn_red_conf.red_enable = false
default_ecn_red_conf.min_threshold_bytes = 150000
default_ecn_red_conf.max_threshold_bytes = 1500000
default_ecn_red_conf.probability = 100

#ecn_red.port_group_list = [ecn_red_port_group]
#ecn_red.ecn_red_port_group.egress_queue_list = [1]
#ecn_red.ecn_red_port_group.port_set = allports
#ecn_red.ecn_red_port_group.ecn_enable = true
#ecn_red.ecn_red_port_group.red_enable = false
#ecn_red.ecn_red_port_group.min_threshold_bytes = 40000
#ecn_red.ecn_red_port_group.max_threshold_bytes = 200000
#ecn_red.ecn_red_port_group.probability = 100

# Hierarchical traffic shaping
# to configure shaping at 2 levels:
#     - per egress queue egr_queue_0 - egr_queue_7
#     - port level aggregate
# -- add or replace a port group names in the port group list
# -- for each port group in the list
#    -- populate the port set, e.g.
#       swp1-swp4,swp8,swp50s0-swp50s3
#    -- set min and max rates in kbps for each egr_queue [min, max]
#    -- set max rate in kbps at port level
# shaping.port_group_list = [shaper_port_group]
# shaping.shaper_port_group.port_set = swp1-swp3,swp5,swp7s0-swp7s3
# shaping.shaper_port_group.egr_queue_0.shaper = [50000, 100000]
# shaping.shaper_port_group.egr_queue_1.shaper = [51000, 150000]
# shaping.shaper_port_group.egr_queue_2.shaper = [52000, 200000]
# shaping.shaper_port_group.egr_queue_3.shaper = [53000, 250000]
# shaping.shaper_port_group.egr_queue_4.shaper = [54000, 300000]
# shaping.shaper_port_group.egr_queue_5.shaper = [55000, 350000]
# shaping.shaper_port_group.egr_queue_6.shaper = [56000, 400000]
# shaping.shaper_port_group.egr_queue_7.shaper = [57000, 450000]
# shaping.shaper_port_group.port.shaper = 900000

# default egress scheduling weight per egress queue
# To be applied to all the ports if port_group profile not configured
# If you do not specify any bw_percent of egress_queues, those egress queues
# will assume DWRR weight 0 - no egress scheduling for those queues
# '0' indicates strict priority

default_egress_sched.egr_queue_0.bw_percent = 12
default_egress_sched.egr_queue_1.bw_percent = 13
default_egress_sched.egr_queue_2.bw_percent = 12
default_egress_sched.egr_queue_3.bw_percent = 13
default_egress_sched.egr_queue_4.bw_percent = 12
default_egress_sched.egr_queue_5.bw_percent = 13
default_egress_sched.egr_queue_6.bw_percent = 12
default_egress_sched.egr_queue_7.bw_percent = 13

# port_group profile for egress scheduling weight per egress queue
# If you do not specify any bw_percent of egress_queues, those egress queues
# will assume DWRR weight 0 - no egress scheduling for those queues
# '0' indicates strict priority
#egress_sched.port_group_list = [sched_port_group1]
#egress_sched.sched_port_group1.port_set = swp2
#egress_sched.sched_port_group1.egr_queue_0.bw_percent = 10
#egress_sched.sched_port_group1.egr_queue_1.bw_percent = 20
#egress_sched.sched_port_group1.egr_queue_2.bw_percent = 30
#egress_sched.sched_port_group1.egr_queue_3.bw_percent = 10
#egress_sched.sched_port_group1.egr_queue_4.bw_percent = 10
#egress_sched.sched_port_group1.egr_queue_5.bw_percent = 10
#egress_sched.sched_port_group1.egr_queue_6.bw_percent = 10
#egress_sched.sched_port_group1.egr_queue_7.bw_percent = 0

# Cut-through is disabled by default on all chips with the exception of
# Spectrum.  On Spectrum cut-through cannot be disabled.
#cut_through_enable = false

qos_infra.conf

#
# Default qos-infra configuration for Mellanox Spectrum chip
#
# Copyright © 2021 NVIDIA CORPORATION & AFFILIATES. ALL RIGHTS RESERVED.
#
# This software product is a proprietary product of Nvidia Corporation and its affiliates
# (the "Company") and all right, title, and interest in and to the software
# product, including all associated intellectual property rights, are and
# shall remain exclusively with the Company.
#
# This software product is governed by the End User License Agreement
# provided with the software product. 

# scheduling algorithm: algorithm values = {dwrr}
scheduling.algorithm = dwrr

# priority groups
# supported group names are control, bulk, service1-6
traffic.priority_group_list = [bulk]

# internal cos values assigned to each priority group
# each cos value should be assigned exactly once
# internal cos values {0..7}
priority_group.bulk.cos_list = [0,1,2,3,4,5,6,7]

# Alias Name defined for each priority group
# Valid string between 0-255 chars
# Sample alias support for naming priority groups
#priority_group.bulk.alias = "Bulk"

# priority group ID assigned to each priority group
#priority_group.control.id = 7
#priority_group.service2.id = 2
priority_group.bulk.id = 0

# all priority groups share a service pool on Spectrum
# service pools assigned to each priority group
priority_group.bulk.service_pool = 0

# service pool assigned for lossless PGs
#flow_control.ingress_service_pool = 0

# --- ingress buffer space allocations ---
# total buffer
#  - ingress minimum buffer allocations
#  - ingress service pool buffer allocations
#  - priority group ingress headroom allocations
#  - ingress global headroom allocations
#  = total ingress shared buffer size

# ingress service pool buffer allocation: percent of total buffer
# If a service pool has no priority groups, the buffer is added
# to the shared buffer space.
ingress_service_pool.0.percent = 100

# Ingress buffer port.pool buffer : size in bytes
#port.service_pool.0.ingress_buffer.reserved = 10240
#port.service_pool.0.ingress_buffer.shared_size = 9000
#port.management.ingress_buffer.reserved = 0


# priority group minimum buffer allocation: size in bytes
# priority group shared buffer allocation: shared buffer size in bytes
# if a priority group has no packet priority values assigned to it, the buffers will not be allocated

#priority_group.bulk.ingress_buffer.reserved           = 0
#priority_group.bulk.ingress_buffer.shared_size        = 15

# ---- ingress dynamic buffering settings
# To enable ingress static pool, set the mode to 0
ingress_service_pool.0.mode = 1

# The ALPHA defines the max% of buffers (quota) available on a
# per ingress port OR ipool, Ingress PG, Egress TC, Egress port OR epool.
# ALPHA value equates to the following buffer limit calculated as:
# alpha%(alpha+1) = Max Buffer percentage

# https://community.mellanox.com/s/article/understanding-the-alpha-parameter-in-the-buffer-configuration-of-mellanox-spectrum-switches
# Each shared buffer pool can use a maximum of [total_buffer * (alpha / (alpha+1))]
# Configure quota values mapped to the following alpha values:
# Configuration value = alpha level:
# Both ALPHA_*(string representation) as well as integer values (old representation) will be supported for alpha
# 0/ALPHA_0  = alpha 0
# 1/ALPHA_1_128  = alpha 1/128
# 2/ALPHA_1_64  = alpha 1/64
# 3/ALPHA_1_32  = alpha 1/32
# 4/ALPHA_1_16  = alpha 1/16
# 5/ALPHA_1_8  = alpha 1/8
# 6/ALPHA_1_4  = alpha 1/4
# 7/ALPHA_1_2  = alpha 1/2
# 8/ALPHA_1  = alpha  1
# 9/ALPHA_2  = alpha  2
# 10/ALPHA_4 = alpha  4
# 11/ALPHA_8 = alpha  8
# 12/ALPHA_16 = alpha 16
# 13/ALPHA_32 = alpha 32
# 14/ALPHA_64 = alpha 64
# 15/ALPHA_INFINITY = alpha Infinity

# Ingress buffer per-port dynamic buffering alpha (Default: ALPHA_8)
#port.service_pool.0.ingress_buffer.dynamic_quota = ALPHA_8
#port.management.ingress_buffer.dynamic_quota = ALPHA_8


# Ingress buffer dynamic buffering alpha for lossless PGs (if any; Default: ALPHA_1)
#flow_control.ingress_buffer.dynamic_quota = ALPHA_1

# Ingress buffer per-PG dynamic buffering alpha (Default: ALPHA_8)
#priority_group.bulk.ingress_buffer.dynamic_quota = ALPHA_8

# --- egress buffer space allocations ---
# total egress buffer
#  - minimum buffer allocations
#  = total service pool buffer size
# service pool assigned for lossless PGs
#flow_control.egress_service_pool = 0

# service pool assigned for egress queues
egress_buffer.egr_queue_0.uc.service_pool = 0
egress_buffer.egr_queue_1.uc.service_pool = 0
egress_buffer.egr_queue_2.uc.service_pool = 0
egress_buffer.egr_queue_3.uc.service_pool = 0
egress_buffer.egr_queue_4.uc.service_pool = 0
egress_buffer.egr_queue_5.uc.service_pool = 0
egress_buffer.egr_queue_6.uc.service_pool = 0
egress_buffer.egr_queue_7.uc.service_pool = 0

# Service pool buffer allocation: percent of total
# buffer size.
egress_service_pool.0.percent = 100

# Egress buffer port.pool buffer : size in bytes
#port.service_pool.0.egress_buffer.uc.reserved = 10240
#port.service_pool.0.egress_buffer.uc.shared_size = 9000
#port.management.egress_buffer.reserved = 0

# Front panel port egress buffer limits enforced for each
# priority group.
# Unlimited egress buffers not supported on Spectrum.
#priority_group.bulk.unlimited_egress_buffer     = false

# if a priority group has no cos values assigned to it, the buffers will not be allocated

# Service pool mapping for MC.SP region
egress_buffer.cos_0.mc.service_pool = 0
egress_buffer.cos_1.mc.service_pool = 0
egress_buffer.cos_2.mc.service_pool = 0
egress_buffer.cos_3.mc.service_pool = 0
egress_buffer.cos_4.mc.service_pool = 0
egress_buffer.cos_5.mc.service_pool = 0
egress_buffer.cos_6.mc.service_pool = 0
egress_buffer.cos_7.mc.service_pool = 0
# Reserved and static shared buffer allocation for MC.SP region: size in bytes
#egress_buffer.cos_0.mc.reserved = 10240
#egress_buffer.cos_1.mc.reserved = 10240
#egress_buffer.cos_2.mc.reserved = 10240
#egress_buffer.cos_3.mc.reserved = 10240
#egress_buffer.cos_4.mc.reserved = 10240
#egress_buffer.cos_5.mc.reserved = 10240
#egress_buffer.cos_6.mc.reserved = 10240
#egress_buffer.cos_7.mc.reserved = 10240
#egress_buffer.cos_0.mc.shared_size = 40
#egress_buffer.cos_1.mc.shared_size = 40
#egress_buffer.cos_2.mc.shared_size =  5
#egress_buffer.cos_3.mc.shared_size = 40
#egress_buffer.cos_4.mc.shared_size = 40
#egress_buffer.cos_5.mc.shared_size = 40
#egress_buffer.cos_6.mc.shared_size = 40
#egress_buffer.cos_7.mc.shared_size = 30

# Shared buffer allocation for ePort.TC region : size in bytes.
#egress_buffer.egr_queue_0.uc.shared_size   = 40
#egress_buffer.egr_queue_1.uc.shared_size   = 40
#egress_buffer.egr_queue_2.uc.shared_size   =  5
#egress_buffer.egr_queue_3.uc.shared_size   = 40
#egress_buffer.egr_queue_4.uc.shared_size   = 40
#egress_buffer.egr_queue_5.uc.shared_size   = 40
#egress_buffer.egr_queue_6.uc.shared_size   = 40
#egress_buffer.egr_queue_7.uc.shared_size   = 30

# Minimum buffer allocation for ePort.TC region: size in bytes
#egress_buffer.egr_queue_0.uc.reserved = 1024
#egress_buffer.egr_queue_1.uc.reserved = 1024
#egress_buffer.egr_queue_2.uc.reserved = 1024
#egress_buffer.egr_queue_3.uc.reserved = 1024
#egress_buffer.egr_queue_4.uc.reserved = 1024
#egress_buffer.egr_queue_5.uc.reserved = 1024
#egress_buffer.egr_queue_6.uc.reserved = 1024
#egress_buffer.egr_queue_7.uc.reserved = 1024

# Reserved Egress buffer for TCs mapped to lossless SPs
#flow_control.egress_buffer.reserved = 0

# Egress buffer ePort.MC buffer : size in bytes
# the per-port limit on multicast packets (applies to all switch priorities)
#port.egress_buffer.mc.reserved = 10240
#port.egress_buffer.mc.shared_size = 92160

# To enable egress static pool, set the mode to 0
egress_service_pool.0.mode = 1

# Egress dynamic buffer pool configuration
# Replace the shared_size parameter with the dynamic_quota=n/ALPHA_x,
# where ‘n’ should be the configuration value for alpha.
# 		‘ALPHA_x’ should be string representation for alpha.
# Pls note : Same alpha configuration values can be used as mentioned in Ingress Dynamic Buffering section above
# Egress buffer per-port dynamic buffering quota (alpha ; Default: ALPHA_16)
#port.service_pool.0.egress_buffer.uc.dynamic_quota = ALPHA_16
#port.management.egress_buffer.dynamic_quota = ALPHA_8


# Egress buffer per-egress-queue dynamic buffering quota (alpha) for lossless egress queues (Default: ALPHA_INFINITY)
#flow_control.egress_buffer.dynamic_quota = ALPHA_1

# Egress buffer per-egress-queue dynamic buffering quota (alpha) for unicast (Default: ALPHA_8)
#egress_buffer.egr_queue_0.uc.dynamic_quota = ALPHA_8
#egress_buffer.egr_queue_1.uc.dynamic_quota = ALPHA_8
#egress_buffer.egr_queue_2.uc.dynamic_quota = ALPHA_8
#egress_buffer.egr_queue_3.uc.dynamic_quota = ALPHA_8
#egress_buffer.egr_queue_4.uc.dynamic_quota = ALPHA_8
#egress_buffer.egr_queue_5.uc.dynamic_quota = ALPHA_8
#egress_buffer.egr_queue_6.uc.dynamic_quota = ALPHA_8
#egress_buffer.egr_queue_7.uc.dynamic_quota = ALPHA_8

# Egress buffer per-egress-queue dynamic buffering quota (alpha) for multicast (Default: ALPHA_INFINITY)
#egress_buffer.egr_queue_0.mc.dynamic_quota    = ALPHA_2
#egress_buffer.egr_queue_1.mc.dynamic_quota = ALPHA_4
#egress_buffer.egr_queue_2.mc.dynamic_quota = ALPHA_1
#egress_buffer.egr_queue_3.mc.dynamic_quota = ALPHA_1_2
#egress_buffer.egr_queue_4.mc.dynamic_quota = ALPHA_1_4
#egress_buffer.egr_queue_5.mc.dynamic_quota = ALPHA_1_8
#egress_buffer.egr_queue_6.mc.dynamic_quota = ALPHA_1_16
#egress_buffer.egr_queue_7.mc.dynamic_quota = ALPHA_INFINITY

# These parameters can be assigned to the virtual Multicast port as well (Default: ALPHA_1_4)
#egress_buffer.cos_0.mc.dynamic_quota = ALPHA_1_4
#egress_buffer.cos_1.mc.dynamic_quota = ALPHA_1_4
#egress_buffer.cos_2.mc.dynamic_quota = ALPHA_1_4
#egress_buffer.cos_3.mc.dynamic_quota = ALPHA_1_4
#egress_buffer.cos_4.mc.dynamic_quota = ALPHA_1_4
#egress_buffer.cos_5.mc.dynamic_quota = ALPHA_1_4
#egress_buffer.cos_6.mc.dynamic_quota = ALPHA_1_4
#egress_buffer.cos_7.mc.dynamic_quota = ALPHA_1_4

# internal cos values mapped to egress queues
# multicast queue: same as unicast queue
cos_egr_queue.cos_0.uc  = 0
cos_egr_queue.cos_0.cpu = 0

cos_egr_queue.cos_1.uc  = 1
cos_egr_queue.cos_1.cpu = 1

cos_egr_queue.cos_2.uc  = 2
cos_egr_queue.cos_2.cpu = 2

cos_egr_queue.cos_3.uc  = 3
cos_egr_queue.cos_3.cpu = 3

cos_egr_queue.cos_4.uc  = 4
cos_egr_queue.cos_4.cpu = 4

cos_egr_queue.cos_5.uc  = 5
cos_egr_queue.cos_5.cpu = 5

cos_egr_queue.cos_6.uc  = 6
cos_egr_queue.cos_6.cpu = 6

cos_egr_queue.cos_7.uc  = 7
cos_egr_queue.cos_7.cpu = 7

Caveats

Configure QoS and Breakout Ports Simultaneously

If you configure btoh breakout ports and QoS settings for breakout interfaces at the same time, errors might occur.

You must apply breakout port configuration before QoS configuration on the breakout ports. If you are using NVUE, configure breakout ports and perform an nv config apply first, then configure QoS settings on the breakout ports followed by another nv config apply. If you are using linux file configuration, modify ports.conf first, reload switchd, then modify qos_features.conf and reload switchd a second time.

QoS Settings on Bond Member Interfaces

If you use Linux commands to apply QoS settings on bond member interfaces instead of the logical bond interface, the members must share identical QoS configuration. If the configuration is not identical between bond interfaces, the bond inherits the _last_ interface you apply to the bond.

If QoS settings do not match, switchd reload fails; however, switchd restart does not fail.

NVUE rejects QoS configurations on bond member interfaces and shows an error when you try to apply the configurations; you must apply all QoS configuration on logical bond interfaces.

Cut-through Switching

You cannot disable cut-through switching on Spectrum ASICs. Cumulus Linux ignores the cut_through_enable = false setting in the qos_features.conf file.