Managing Cumulus Linux Disk Images
The Cumulus Linux operating system resides on a switch as a disk image. This section discusses how to manage the image.
To install a new Cumulus Linux image, refer to Installing a New Cumulus Linux Image. To upgrade Cumulus Linux, refer to Upgrading Cumulus Linux.
Reprovision the System (Restart the Installer)
Reprovisioning the system deletes all system data from the switch.
To stage an ONIE installer from the network (where ONIE automatically locates the installer), run the onie-select -i command. You must reboot the switch to start the install process.
cumulus@switch:~$ sudo onie-select -i
WARNING:
WARNING: Operating System install requested.
WARNING: This will wipe out all system data.
WARNING:
Are you sure (y/N)? y
Enabling install at next reboot...done.
Reboot required to take effect.
To cancel a pending reinstall operation, run the onie-select -c command:
cumulus@switch:~$ sudo onie-select -c
Cancelling pending install at next reboot...done.
To stage an installer located in a specific location, run the onie-install -i <location> command. You can specify a local, absolute or relative path, an HTTP or HTTPS server, SCP or FTP server. You can also stage a Zero Touch Provisioning (ZTP) script along with the installer.
You typically use the onie-install command with the -a option to activate installation. If you do not specify the -a option, you must reboot the switch to start the installation process.
The following example stages the installer located at http://203.0.113.10/image-installer together with the ZTP script located at http://203.0.113.10/ztp-script and activates installation and ZTP:
cumulus@switch:~$ sudo onie-install -i http://203.0.113.10/image-installer
cumulus@switch:~$ sudo onie-install -z http://203.0.113.10/ztp-script
cumulus@switch:~$ sudo onie-install -a
You can also specify these options together in the same command. For example:
cumulus@switch:~$ sudo onie-install -i http://203.0.113.10/image-installer -z http://203.0.113.10/ztp-script -a
To see more onie-install options, run man onie-install.
Migrate from Cumulus Linux to ONIE (Uninstall All Images and Remove the Configuration)
To remove all installed images and configurations, and return the switch to its factory defaults, run the onie-select -k command.
The onie-select -k command takes a long time to run as it overwrites the entire NOS section of the flash. Only use this command if you want to erase all NOS data and take the switch out of service.
cumulus@switch:~$ sudo onie-select -k
WARNING:
WARNING: Operating System uninstall requested.
WARNING: This will wipe out all system data.
WARNING:
Are you sure (y/N)? y
Enabling uninstall at next reboot...done.
Reboot required to take effect.
You must reboot the switch to start the uninstallation process.
To cancel a pending uninstall operation, run the onie-select -c command:
cumulus@switch:~$ sudo onie-select -c
Cancelling pending uninstall at next reboot...done.
Boot Into Rescue Mode
If your system becomes unresponsive, you can correct certain issues by booting into ONIE rescue mode, which uses unmounted file systems. You can use various Cumulus Linux utilities to try and resolve a problem.
To reboot the system into ONIE rescue mode, run the onie-select -r command:
cumulus@switch:~$ sudo onie-select -r
WARNING:
WARNING: Rescue boot requested.
WARNING:
Are you sure (y/N)? y
Enabling rescue at next reboot...done.
Reboot required to take effect.
You must reboot the system to boot into rescue mode.
To cancel a pending rescue boot operation, run the onie-select -c command:
cumulus@switch:~$ sudo onie-select -c
Cancelling pending rescue at next reboot...done.
Inspect the Image File
The Cumulus Linux image file is executable. From a running switch, you can display, extract, and verify the contents of the image file.
To display the contents of the Cumulus Linux image file, pass the info option to the image file. For example, to display the contents of an image file called onie-installer located in the /var/lib/cumulus/installer directory:
cumulus@switch:~$ sudo /var/lib/cumulus/installer/onie-installer info
Verifying image checksum ...OK.
Preparing image archive ... OK.
Control File Contents
=====================
Description: Cumulus Linux 4.1.0
Release: 4.1.0
Architecture: amd64
Switch-Architecture: bcm-amd64
Build-Id: dirtyz224615f
Build-Date: 2019-05-17T16:34:22+00:00
Build-User: clbuilder
Homepage: http://www.cumulusnetworks.com/
Min-Disk-Size: 1073741824
Min-Ram-Size: 536870912
mkimage-version: 0.11.111_gbcf0
To extract the contents of the image file, use with the extract <path> option. For example, to extract an image file called onie-installer located in the /var/lib/cumulus/installer directory to the mypath directory:
cumulus@switch:~$ sudo /var/lib/cumulus/installer/onie-installer extract mypath
total 181860
-rw-r--r-- 1 4000 4000 308 May 16 19:04 control
drwxr-xr-x 5 4000 4000 4096 Apr 26 21:28 embedded-installer
-rw-r--r-- 1 4000 4000 13273936 May 16 19:04 initrd
-rw-r--r-- 1 4000 4000 4239088 May 16 19:04 kernel
-rw-r--r-- 1 4000 4000 168701528 May 16 19:04 sysroot.tar
To verify the contents of the image file, use with the verify option. For example, to verify the contents of an image file called onie-installer located in the /var/lib/cumulus/installer directory:
cumulus@switch:~$ sudo /var/lib/cumulus/installer/onie-installer verify
Verifying image checksum ...OK.
Preparing image archive ... OK.
./cumulus-linux-bcm-amd64.bin.1: 161: ./cumulus-linux-bcm-amd64.bin.1: onie-sysinfo: not found
Verifying image compatibility ...OK.
Verifying system ram ...OK.