If you are using the current version of Cumulus Linux, the content on this page may not be up to date. The current version of the documentation is available here. If you are redirected to the main page of the user guide, then this page may have been renamed; please search for it there.

Open Shortest Path First v2 - OSPFv2

This topic describes OSPFv2, which is a link-state routing protocol for IPv4. For IPv6 commands, refer to Open Shortest Path First v3 - OSPFv3.

Basic OSPFv2 Configuration

You can configure OSPF using either numbered interfaces or unnumbered interfaces.

OSPFv2 Numbered

To configure OSPF using numbered interfaces, you specify the router ID, IP subnet prefix, and area address. You must put all the interfaces on the switch with an IP address that matches the network subnet into the specified area. OSPF attempts to discover other OSPF routers on those interfaces. Cumulus Linux adds all matching interface network addresses to a type-1 LSA and advertises to discovered neighbors for proper reachability.

If you do not want to bring up an OSPF adjacency on certain interfaces, but want to advertise those networks in the OSPF database, you can configure the interfaces as passive interfaces. A passive interface creates a database entry but does not send or receive OSPF hello packets. For example, in a data center topology, the host-facing interfaces do not need to run OSPF, however, you need to advertise the corresponding IP addresses to neighbors.

Network statements can be as inclusive or generic as necessary to cover the interface networks.

The following example commands configure OSPF numbered on leaf01 and spine01.

leaf01 spine01
  • The loopback address is 10.10.10.1/32
  • The IP address on swp51 is 10.0.1.0/31
  • The router ID is 10.10.10.1
  • All the interfaces on the switch with an IP address that matches subnet 10.10.10.1/32 and swp51 with IP address 10.0.1.0/31 are in area 0
  • swp1 and swp2 are passive interfaces
  • The loopback address is 10.10.10.101/32
  • The IP address on swp1 is 10.0.1.1/31
  • The router ID is 10.10.10.101
  • All interfaces on the switch with an IP address that matches subnet 10.10.10.101/32 and swp1 with IP address 10.0.1.1/31 are in area 0.
cumulus@leaf01:~$ nv set interface lo ip address 10.10.10.1/32
cumulus@leaf01:~$ nv set interface swp51 ip address 10.0.1.0/31
cumulus@leaf01:~$ nv set vrf default router ospf router-id 10.10.10.1
cumulus@leaf01:~$ nv set vrf default router ospf area 0 network 10.10.10.1/32
cumulus@leaf01:~$ nv set vrf default router ospf area 0 network 10.0.1.0/31
cumulus@leaf01:~$ nv set interface swp1 router ospf passive on
cumulus@leaf01:~$ nv set interface swp2 router ospf passive on
cumulus@leaf01:~$ nv config apply
cumulus@spine01:~$ nv set interface lo ip address 10.10.10.101/32
cumulus@spine01:~$ nv set interface swp1 ip address 10.0.1.1/31
cumulus@spine01:~$ nv set vrf default router ospf router-id 10.10.10.101
cumulus@spine01:~$ nv set vrf default router ospf area 0 network 10.10.10.101/32
cumulus@spine01:~$ nv set vrf default router ospf area 0 network 10.0.1.1/31
cumulus@spine01:~$ nv config apply
  1. Edit the /etc/frr/daemons file to enable the ospf daemon, then start the FRR service (see FRRouting).

  2. Edit the /etc/network/interfaces file to configure the IP address for the loopback and swp51:

cumulus@leaf01:~$ sudo nano /etc/network/interfaces
...
auto lo
iface lo inet loopback
  address 10.10.10.1/32

auto swp51 iface swp51 address 10.0.1.0/31

  1. Run the ifreload -a command to load the new configuration:

    cumulus@leaf01:~$ sudo ifreload -a
    
  2. From the vtysh shell, configure OSPF:

    cumulus@leaf01:~$ sudo vtysh
    ...
    leaf01# configure terminal
    leaf01(config)# router ospf
    leaf01(config-router)# ospf router-id 10.10.10.1
    leaf01(config-router)# network 10.10.10.1/32 area 0
    leaf01(config-router)# network 10.0.1.0/31 area 0
    leaf01(config-router)# passive-interface swp1
    leaf01(config-router)# passive-interface swp2
    leaf01(config-router)# exit
    leaf01(config)# exit
    leaf01# write memory
    leaf01# exit
    

You can use the passive-interface default command to set all interfaces as passive and selectively bring up protocol adjacency on certain interfaces:

leaf01(config)# router ospf
leaf01(config-router)# passive-interface default
leaf01(config-router)# no passive-interface swp51

The vtysh commands save the configuration in the /etc/frr/frr.conf file. For example:

...
router ospf
 ospf router-id 10.10.10.1
 network 10.10.10.1/32 area 0
 network 10.0.1.0/31 area 0
 passive-interface swp1
 passive-interface swp2
...
  1. Edit the /etc/frr/daemons file to enable the ospf daemon, then start the FRR service (see FRRouting).

  2. Edit the /etc/network/interfaces file to configure the IP address for the loopback and swp1:

    cumulus@spine01:~$ sudo nano /etc/network/interfaces
    ...
    auto lo
    iface lo inet loopback
      address 10.10.10.101/32
    

    auto swp51 iface swp51 address 10.0.1.1/31

  3. Run the ifreload -a command to load the new configuration:

    cumulus@spine01:~$ sudo ifreload -a
    
  4. From the vtysh shell, configure OSPF:

    cumulus@spine01:~$ sudo vtysh
    ...
    spine01# configure terminal
    spine01(config)# router ospf
    spine01(config-router)# ospf router-id 10.10.101.1
    spine01(config-router)# network 10.10.10.101/32 area 0
    spine01(config-router)# network 10.0.1.1/31 area 0
    spine01(config-router)# exit
    spine01(config)# exit
    spine01# write memory
    spine01# exit
    

You can use the passive-interface default command to set all interfaces as passive and selectively bring up protocol adjacency on certain interfaces:

spine01(config)# router ospf
spine01(config-router)# passive-interface default
spine01(config-router)# no passive-interface swp1

The vtysh commands save the configuration in the /etc/frr/frr.conf file. For example:

...
router ospf
 ospf router-id 10.10.10.101
 network 10.10.10.101/32 area 0
 network 10.0.1.1/31 area 0
...

OSPFv2 Unnumbered

Unnumbered interfaces are interfaces without unique IP addresses; multiple interfaces share the same IP address. In OSPFv2, unnumbered interfaces do not need unique IP addresses on leaf and spine interfaces and simplify the OSPF database, which reduces the memory footprint and improves SPF convergence times.

To configure an unnumbered interface, take the IP address of loopback interface (called the anchor) and use that as the IP address of the unnumbered interface.

OSPF unnumbered supports point-to-point interfaces only and does not support network statements.

The following example commands configure OSPF unnumbered on leaf01 and spine01.

leaf01 spine01
  • The loopback address is 10.10.10.1/32
  • The IP address of the unnumbered interface (swp51) is 10.10.10.1/32
  • The router ID is 10.10.10.1
  • OSPF is on the loopback interface and on swp51 in area 0
  • swp1 and swp2 are passive interfaces
  • swp51 is a point-to-point interface (Cumulus Linux requires point-to-point for unnumbered interfaces)
    • The loopback address is 10.10.10.101/32
    • The IP address of the unnumbered interface (swp1) is 10.10.10.101/32
    • The router ID is 10.10.10.101
    • OSPF is on the loopback interface and on swp1 in area 0
    • swp1 is a point-to-point interface (Cumulus Linux requires point-to-point for unnumbered interfaces)

      Configure the unnumbered interface:

      cumulus@leaf01:~$ nv set interface lo ip address 10.10.10.1/32
      cumulus@leaf01:~$ nv set interface swp51 ip address 10.10.10.1/32
      cumulus@leaf01:~$ nv config apply
      

      Configure OSPF:

      cumulus@leaf01:~$ nv set vrf default router ospf router-id 10.10.10.1
      cumulus@leaf01:~$ nv set interface lo router ospf area 0
      cumulus@leaf01:~$ nv set interface swp51 router ospf area 0
      cumulus@leaf01:~$ nv set interface swp1 router ospf passive on
      cumulus@leaf01:~$ nv set interface swp2 router ospf passive on
      cumulus@leaf01:~$ nv set interface swp51 router ospf network-type point-to-point
      cumulus@leaf01:~$ nv config apply
      

      Configure the unnumbered interface:

      cumulus@spine01:~$ nv set interface lo ip address 10.10.10.101/32
      cumulus@spine01:~$ nv set interface swp1 ip address 10.10.10.101/32
      cumulus@spine01:~$ nv config apply
      

      Configure OSPF:

      cumulus@spine01:~$ nv set vrf default router ospf router-id 10.10.10.101
      cumulus@spine01:~$ nv set interface lo router ospf area 0
      cumulus@spine01:~$ nv set interface swp1 router ospf area 0
      cumulus@spine01:~$ nv set interface swp1 router ospf network-type point-to-point
      cumulus@spine01:~$ nv config apply
      
      1. Edit the /etc/frr/daemons file to enable the ospf daemon, then start the FRR service (see FRRouting).

      2. Edit the /etc/network/interfaces file to configure the loopback and unnumbered interface address:

        cumulus@leaf01:~$ sudo nano /etc/network/interfaces
        ...
        auto lo
        iface lo inet loopback
          address 10.10.10.1/32
        

        auto swp51 iface swp51 address 10.10.10.1/32

      3. Run the ifreload -a command to load the new configuration:

        cumulus@leaf01:~$ ifreload -a
        
      4. From the vtysh shell, configure OSPF:

        cumulus@leaf01:~$ sudo vtysh
        ...
        leaf01# configure terminal
        leaf01(config)# router ospf
        leaf01(config-router)# ospf router-id 10.10.10.1
        leaf01(config-router)# interface swp51
        leaf01(config-if)# ip ospf area 0
        leaf01(config-if)# ip ospf network point-to-point
        leaf01(config-if)# exit
        leaf01(config)# interface lo
        leaf01(config-if)# ip ospf area 0
        leaf01(config-if)# exit
        leaf01(config)# router ospf
        leaf01(config-router)# passive-interface swp1,swp2
        leaf01(config-router)# end
        leaf01# write memory
        leaf01# exit
        

        You can use the passive-interface default command to set all interfaces as passive and selectively bring up protocol adjacency on certain interfaces:

        leaf01(config)# router ospf
        leaf01(config-router)# passive-interface default
        leaf01(config-router)# no passive-interface swp51
        

      The vtysh commands save the configuration in the /etc/frr/frr.conf file. For example:

      ...
      interface lo
       ip ospf area 0
      interface swp51
       ip ospf area 0
       ip ospf network point-to-point
      router ospf
       ospf router-id 10.10.10.1
       passive-interface swp1,swp2
      ...
      
      1. Edit the /etc/frr/daemons file to enable the ospf daemon, then start the FRR service (see FRRouting).

      2. Edit the /etc/network/interfaces file to configure the loopback and unnumbered interface address:

        cumulus@spine01:~$ sudo nano /etc/network/interfaces
        ...
        auto lo
        iface lo inet loopback
           address 10.10.10.101/32
        

        auto swp1 iface swp1 address 10.10.10.101/32

      3. Run the ifreload -a command to load the new configuration:

        cumulus@spine01:~$ sudo ifreload -a
        
      4. From the vtysh shell, configure OSPF:

        cumulus@spine01:~$ sudo vtysh
        ...
        spine01# configure terminal
        spine01(config)# router ospf
        spine01(config)# ospf router-id 10.10.10.101
        spine01(config)# interface swp1
        spine01(config-if)# ip ospf area 0
        spine01(config-if)# ip ospf network point-to-point
        spine01(config-if)# exit
        spine01(config)# interface lo
        spine01(config-if)# ip ospf area 0
        spine01(config-if)# exit
        spine01(config-if)# end
        spine01# write memory
        spine01# exit
        

        You can use the passive-interface default command to set all interfaces as passive and selectively bring up protocol adjacency on certain interfaces:

        spine01(config)# router ospf
        spine01(config-router)# passive-interface default
        spine01(config-router)# no passive-interface swp1
        

      The vtysh commands save the configuration in the /etc/frr/frr.conf file. For example:

      ...
      interface lo
       ip ospf area 0
      interface swp1
       ip ospf area 0
       ip ospf network point-to-point
      router ospf
       ospf router-id 10.10.10.101
      ...
      

      Optional OSPFv2 Configuration

      This section describes optional configuration. The steps provided in this section assume that you already configured basic OSPFv2 as described in Basic OSPF Configuration, above.

      Interface Parameters

      You can define the following OSPF parameters per interface:

      • Network type (point-to-point or broadcast). Broadcast is the default setting. Configure the interface as point-to-point unless you intend to use the Ethernet media as a LAN with multiple connected routers. Point-to-point provides a simplified adjacency state machine so there is no need for DR/BDR election and LSA reflection. See RFC5309 for a more information.

        Cumulus Linux requires Point-to-point for OSPFv2 unnumbered.

      • Hello interval. The number of seconds between hello packets sent on the interface. The default is 10 seconds.
      • Dead interval. The number of seconds before neighbors declare the router down after they stop hearing hello packets. The default is 40 seconds.
      • Priority in becoming the OSPF Designated Router (DR) on a broadcast interface. The default is priority 1.

      The following command example sets the network type to point-to-point.

      cumulus@switch:~$ nv set interface swp51 router ospf network-type point-to-point
      cumulus@switch:~$ nv config apply
      
      cumulus@switch:~$ sudo vtysh
      ...
      switch# configure terminal
      switch(config)# interface swp51
      switch(config-if)# ip ospf network point-to-point
      switch(config-if)# end
      switch# write memory
      switch# exit
      

      The vtysh commands save the configuration in the /etc/frr/frr.conf file. For example

      ...
      interface swp51
       ip ospf network point-to-point
      ...
      

      The following command example sets the hello interval to 5 seconds and the dead interval to 60 seconds. The hello interval and dead interval can be any value between 1 and 65535 seconds.

      cumulus@switch:~$ nv set interface swp51 router ospf timers hello-interval 5
      cumulus@switch:~$ nv config apply
      
      cumulus@switch:~$ sudo vtysh
      ...
      switch# configure terminal
      switch(config)# interface swp51
      switch(config-if)# ip ospf network hello-interval 5
      switch(config-if)# ip ospf network dead-interval 60
      switch(config-if)# end
      switch# write memory
      switch# exit
      

      The vtysh commands save the configuration in the /etc/frr/frr.conf file. For example

      ...
      interface swp51
       ip ospf hello-interval 5
       ip ospf dead-interval 60
      ...
      

      The following command example sets the priority to 5 for swp51. The priority can be any value between 0 to 255. 0 configures the interface to never become the OSPF Designated Router (DR) on a broadcast interface.

      cumulus@switch:~$ nv set interface swp51 router ospf priority 5
      cumulus@switch:~$ nv config apply
      
      cumulus@switch:~$ sudo vtysh
      ...
      switch# configure terminal
      switch(config)# interface swp51
      switch(config-if)# ip ospf network priority 5
      switch(config-if)# end
      switch# write memory
      switch# exit
      

      The vtysh commands save the configuration in the /etc/frr/frr.conf file. For example

      ...
      interface swp51
       ip ospf priority 5
      ...
      

      To see the configured OSPF interface parameter values, run the vtysh show ip ospf interface command.

      SPF Timer Defaults

      OSPF uses the following default timers to prevent consecutive SPF from overburdening the CPU:

      • 0 milliseconds from the initial event until SPF runs
      • 50 milliseconds between consecutive SPF runs (the number doubles with each SPF, until it reaches the maximum time between SPF runs)
      • 5000 milliseconds maximum between SPFs

      The following example commands change the number of milliseconds from the initial event until SPF runs to 80, the number of milliseconds between consecutive SPF runs to 100, and the maximum number of milliseconds between SPFs to 6000.

      cumulus@switch:~$ nv set router ospf timers spf delay 80
      cumulus@switch:~$ nv set router ospf timers spf holdtime 100
      cumulus@switch:~$ nv set router ospf timers spf max-holdtime 6000
      cumulus@switch:~$ nv config apply
      
      cumulus@switch:~$ sudo vtysh
      ...
      switch# configure terminal
      switch(config)# router ospf
      switch(config-router)# timers throttle spf 80 100 6000
      switch(config-router)# end
      switch# write memory
      switch# exit
      

      The vtysh commands save the configuration in the /etc/frr/frr.conf file. For example:

      ...
      router ospf
       ospf router-id 10.10.10.1
       passive-interface swp1
       passive-interface swp2
       network 10.10.10.1/32 area 0
       timers throttle spf 80 100 6000
      ...
      

      To see the configured SPF timer values, run the vtysh show ip ospf command.

      MD5 Authentication

      To configure MD5 authentication on the switch, you need to create a key and a key ID, then enable MD5 authentication. The key ID must be a value between 1 and 255 that represents the key used to create the message digest. This value must be consistent across all routers on a link. The key must be a value with an upper range of 16 characters (longer strings truncate) that represents the actual message digest.

      The following example commands create key ID 1 with the key thisisthekey and enable MD5 authentication on swp51 on leaf01 and on swp1 on spine01.

      cumulus@leaf01:~$ nv set interface swp51 router ospf authentication message-digest-key 1
      cumulus@leaf01:~$ nv set interface swp51 router ospf authentication md5-key thisisthekey
      cumulus@leaf01:~$ nv set interface swp51 router ospf authentication enable on
      cumulus@leaf01:~$ nv config apply
      
      cumulus@spine01:~$ nv set interface swp1 router ospf authentication message-digest-key 1
      cumulus@spine01:~$ nv set interface swp1 router ospf authentication md5-key thisisthekeynet 
      cumulus@spine01:~$ nv set interface swp1 router ospf authentication enable on
      cumulus@spine01:~$ nv config apply
      
      cumulus@leaf01:~$ sudo vtysh
      ...
      leaf01# configure terminal
      leaf01(config)# interface swp51
      leaf01(config-if)# ip ospf authentication message-digest
      leaf01(config-if)# ip ospf message-digest-key 1 md5 thisisthekey
      leaf01(config-if)# end
      leaf01# write memory
      leaf01# exit
      

      The vtysh commands save the configuration in the /etc/frr/frr.conf file. For example:

      ...
      interface swp51
       ip ospf authentication message-digest
       ip ospf message-digest-key 1 md5 thisisthekey
       ...
      
      cumulus@spine01:~$ sudo vtysh
      ...
      spine01# configure terminal
      spine01(config)# interface swp1
      spine01(config-if)# ip ospf authentication message-digest
      spine01(config-if)# ip ospf message-digest-key 1 md5 thisisthekey
      spine01(config-if)# end
      spine01# write memory
      spine01# exit
      

      The vtysh commands save the configuration in the /etc/frr/frr.conf file. For example:

      ...
      interface swp1
       ip ospf authentication message-digest
       ip ospf message-digest-key 1 md5 thisisthekey
       ...
      

      To remove existing MD5 authentication hashes, run the vtysh no ip ospf command (no ip ospf message-digest-key 1 md5 thisisthekey).

      Summarization and Prefix Range

      By default, an ABR creates a summary (type-3) LSA for each route in an area and advertises it in adjacent areas. Prefix range configuration optimizes this behavior by creating and advertising one summary LSA for multiple routes. OSPF only allows for route summarization between areas on a ABR.

      The following example shows a topology divided into area 0 and area 1. border01 and border02 are ABRs that have links to multiple areas and perform a set of specialized tasks, such as SPF computation per area and summarization of routes across areas.

      On border01:

      • swp1 is in area 1 with IP addresses 10.0.0.24/31, 172.16.1.1/32, 172.16.1.2/32, and 172.16.1.3/32
      • swp51 is in area 0 with IP address 10.0.1.9/31

      These commands create a summary route for all the routes in the range 172.16.1.0/24 in area 0:

      cumulus@leaf01:~$ nv set vrf default router ospf area 0 range 172.16.1.0/24
      cumulus@leaf01:~$ nv config apply
      
      cumulus@leaf01:~$ sudo vtysh
      ...
      leaf01# configure terminal
      leaf01(config)# router ospf
      leaf01(config-router)# area 0 range 172.16.1.0/24
      leaf01(config-router)# end
      leaf01# write memory
      leaf01# exit
      

      The vtysh commands save the configuration in the /etc/frr/frr.conf file. For example:

      cumulus@border01:mgmt:~$ sudo cat /etc/frr/frr.conf
      ...
      interface lo
       ip ospf area 0
      interface swp1
       ip ospf area 1
      interface swp2
       ip ospf area 1
      interface swp51
       ip ospf area 0
      interface swp52
       ip ospf area 0
      router ospf
       ospf router-id 10.10.10.63
       area 0 range 172.16.1.0/24
      

      Stub Areas

      External routes are the routes redistributed into OSPF from another protocol. They have an AS-wide flooding scope. Typically, external link states make up a large percentage of the link-state database (LSDB). Stub areas reduce the LSDB size by not flooding AS-external LSAs.

      All routers must agree that an area is a stub, otherwise they do not become OSPF neighbors.

      To configure a stub area:

      cumulus@switch:~$ nv set vrf default router ospf area 1 type stub
      cumulus@switch:~$ nv config apply
      
      cumulus@switch:~$ sudo vtysh
      ...
      switch# configure terminal
      switch(config)# router ospf
      switch(config-router)# area 1 stub
      switch(config-router)# end
      switch# write memory
      switch# exit
      

      The vtysh commands save the configuration in the /etc/frr/frr.conf file. For example:

      ...
      router ospf
       router-id 10.10.10.63
       area 1 stub
      ...
      

      Stub areas still receive information about networks that belong to other areas of the same OSPF domain. If summarization is not configured (or is not comprehensive), the information can be overwhelming for the nodes. Totally stubby areas address this issue. Routers in totally stubby areas keep information about routing within their area in their LSDB.

      To configure a totally stubby area:

      cumulus@switch:~$ nv set vrf default router ospf area 1 type totally-stub 
      cumulus@switch:~$ nv config apply
      
      cumulus@switch:~$ sudo vtysh
      ...
      switch# configure terminal
      switch(config)# router ospf
      switch(config-router)# area 1 stub no-summary
      switch(config-router)# end
      switch# write memory
      switch# exit
      

      The vtysh commands save the configuration in the /etc/frr/frr.conf file. For example:

      ...
      router ospf
       router-id 10.10.10.63
       area 1 stub no-summary
      ...
      

      Here is a brief summary of the area type differences:

      Type Behavior
      Normal non-zero area LSA types 1, 2, 3, 4 area-scoped, type 5 externals, inter-area routes summarized
      Stub area LSA types 1, 2, 3, 4 area-scoped, no type 5 externals, inter-area routes summarized
      Totally stubby area LSA types 1, 2 area-scoped, default summary, no type 3, 4, 5 LSA types allowed

      Auto-cost Reference Bandwidth

      When you set the auto-cost reference bandwidth, Cumulus Linux dynamically calculates the OSPF interface cost to support higher speed links. The default value is 100000 for 100Gbps link speed. The cost of interfaces with link speeds lower than 100Gbps is higher.

      To avoid routing loops, set the bandwidth to a consistent value across all OSPF routers.

      The following example commands configure the auto-cost reference bandwidth for 90Gbps link speed:

      cumulus@switch:~$ nv set vrf default router ospf reference-bandwidth 9000
      cumulus@switch:~$ nv config apply
      
      cumulus@switch:~$ sudo vtysh
      ...
      switch# configure terminal
      switch(config)# router ospf
      switch(config-router)# auto-cost reference-bandwidth 90000
      switch(config-router)# end
      switch# write memory
      switch# exit
      

      The vtysh commands save the configuration in the /etc/frr/frr.conf file. For example:

      ...
      router ospf
       router-id 10.10.10.1
       auto-cost reference-bandwidth 90000
      ...
      

      Administrative Distance

      Cumulus Linux uses the administrative distance to choose which routing protocol to use when two different protocols provide route information for the same destination. The smaller the distance, the more reliable the protocol. For example, if the switch receives a route from OSPF with an administrative distance of 110 and the same route from BGP with an administrative distance of 100, the switch chooses BGP.

      Cumulus Linux provides several commands to change the distance for OSPF routes. The default value is 110.

      The following example commands set the distance for an entire group of routes:

      The NVUE command is not supported.
      cumulus@switch:~$ sudo vtysh
      ...
      switch# configure terminal
      switch(config)# router ospf
      switch(config-router)# distance 254
      switch(config-router)# end
      switch# write memory
      switch# exit
      

      The following example commands change the OSPF administrative distance to 150 for internal routes and 220 for external routes:

      cumulus@switch:~$ nv set vrf default router ospf distance intra-area 150 
      cumulus@switch:~$ nv set vrf default router ospf distance inter-area 150
      cumulus@switch:~$ nv set vrf default router ospf distance external 220
      cumulus@switch:~$ nv config apply
      
      cumulus@switch:~$ sudo vtysh
      ...
      switch# configure terminal
      switch(config)# router ospf
      switch(config-router)# distance ospf intra-area 150 inter-area 150 external 220
      switch(config-router)# end
      switch# write memory
      switch# exit
      

      The following example commands change the OSPF administrative distance to 150 for internal routes to a subnet or network inside the same area as the router:

      cumulus@switch:~$ nv set vrf default router ospf distance intra-area 150 
      cumulus@switch:~$ nv config apply
      
      cumulus@switch:~$ sudo vtysh
      ...
      switch# configure terminal
      switch(config)# router ospf
      switch(config-router)# distance ospf intra-area 150
      switch(config-router)# end
      switch# write memory
      switch# exit
      

      The following example commands change the OSPF administrative distance to 150 for internal routes to a subnet in an area of which the router is not a part:

      cumulus@switch:~$ nv set vrf default router ospf distance inter-area 150
      cumulus@switch:~$ nv config apply
      
      cumulus@switch:~$ sudo vtysh
      ...
      switch# configure terminal
      switch(config)# router ospf
      switch(config-router)# distance ospf inter-area 150
      switch(config-router)# end
      switch# write memory
      switch# exit
      

      The vtysh commands save the configuration to the /etc/frr/frr.conf file. For example:

      ...
      router ospf
        ospf router-id 10.10.10.1
        distance ospf intra-area 150 inter-area 150 external 220
      ...
      

      Topology Changes and OSPF Reconvergence

      When you remove a router or OSPF interface, LSA updates trigger throughout the network to inform all routers of the topology change. When the switch receives the LSA and runs OSPF, a routing update occurs. This can cause short-duration outages while the network detects the failure and updates the OSPF database.

      With a planned outage (such as during a maintenance window), you can configure the OSPF router with an OSPF max-metric to notify its neighbors not to use it as part of the OSPF topology. While the network converges, all traffic forwarded to the max-metric router is still forwarded. After you update the network, the max-metric router no longer receives any traffic and you can configure the max-metric setting. To remove a single interface, you can configure the OSPF cost for that specific interface.

      For failure events, traffic loss can occur during reconvergence (until SPF on all nodes computes an alternative path around the failed link or node to each of the destinations).

      To configure the max-metric (for all interfaces):

      cumulus@switch:~$ nv set vrf default router ospf max-metric administrative on
      cumulus@switch:~$ nv config apply
      
      cumulus@switch:~$ sudo vtysh
      ...
      switch# configure terminal
      switch(config)# router ospf
      switch(config-router)# max-metric router-lsa administrative
      switch(config-router)# end
      switch# write memory
      switch# exit
      

      To configure the cost (for a specific interface):

      cumulus@switch:~$ nv set interface swp51 router ospf cost 65535
      cumulus@switch:~$ nv config apply
      
      cumulus@switch:~$ sudo vtysh
      ...
      switch# configure terminal
      switch(config)# interface swp51
      switch(config-if)# ospf cost 65535
      switch(config-if)# end
      switch# write memory
      switch# exit
      

      Troubleshooting

      Cumulus Linux provides several OSPF troubleshooting commands:

      Description
      vtysh Command
      Show neighbor states show ip ospf neighbor
      Verify that the LSDB synchronizes across all routers in the network show ip ospf database
      Determine why Cumulus Linux does not forward an OSPF route properly show ip route ospf
      Show OSPF interfaces show ip ospf interface
      Show information about the OSPF process show ip ospf

      The following example shows the show ip ospf neighbor command output:

      cumulus@leaf01:mgmt:~$sudo vtysh
      ...
      leaf01# show ip ospf neighbor
      Neighbor ID     Pri State           Dead Time Address         Interface                        RXmtL RqstL DBsmL
      10.10.10.101      1 Full/Backup       30.307s 10.0.1.1        swp51:10.0.1.0                       0     0     0
      

      The following example shows the show ip route ospf command output:

      cumulus@leaf01:mgmt:~$ sudo vtysh
      ...
      leaf01# show ip route ospf
      Codes: K - kernel route, C - connected, S - static, R - RIP,
             O - OSPF, I - IS-IS, B - BGP, E - EIGRP, N - NHRP,
             T - Table, v - VNC, V - VNC-Direct, A - Babel, D - SHARP,
             F - PBR, f - OpenFabric,
             > - selected route, * - FIB route, q - queued route, r - rejected route
      
      O   10.0.1.0/31 [110/100] is directly connected, swp51, weight 1, 00:02:37
      O   10.10.10.1/32 [110/0] is directly connected, lo, weight 1, 00:02:37
      O>* 10.10.10.101/32 [110/100] via 10.0.1.1, swp51, weight 1, 00:00:57
      

      To capture OSPF packets, run the sudo tcpdump -v -i swp1 ip proto ospf command.