layout-3 layout-6 layout-1 layout-top
NVIDIA Docs Hubchevron_right NVIDIA Networkingchevron_right Networking Softwarechevron_right Switch Softwarechevron_right

Cumulus Linux

layout-top layout-6 layout-1

If you are using the current version of Cumulus Linux, the content on this page may not be up to date. The current version of the documentation is available here. If you are redirected to the main page of the user guide, then this page may have been renamed; please search for it there.

VLAN-aware Bridge Mode

VLAN-aware bridge mode in Cumulus Linux implements a configuration model for large-scale layer 2 environments, with one single instance of spanning tree protocol. Each physical bridge member port includes the list of allowed VLANs as well as the port VLAN ID, either the primary VLAN Identifier (PVID) or native VLAN. MAC address learning, filtering and forwarding are VLAN-aware. This reduces the configuration size, and eliminates the large overhead of managing the port and VLAN instances as subinterfaces, replacing them with lightweight VLAN bitmaps and state updates.

Cumulus Linux supports multiple VLAN-aware bridges but with the following limitations:

  • You cannot use MLAG with multiple VLAN-aware bridges.
  • You cannot use the same port with multiple VLAN-aware bridges.
  • You cannot use the same VNIs in multiple VLAN-aware bridges.
  • You cannot use VLAN translation with multiple VLAN-aware bridges.
  • You cannot use double tagged VLAN interfaces with multiple VLAN-aware bridges.
  • You cannot associate multiple single VXLAN devices (SVDs) with a single VLAN-aware bridge

Configure a VLAN-aware Bridge

The example commands below create a VLAN-aware bridge for STP that contains two switch ports and includes 3 VLANs; tagged VLANs 10 and 20, and untagged (native) VLAN 1.

With NVUE, there is a default bridge called br_default, which has no ports assigned. The example below configures this default bridge.

cumulus@switch:~$ nv set interface swp1-2 bridge domain br_default
cumulus@switch:~$ nv set bridge domain br_default vlan 10,20
cumulus@switch:~$ nv set bridge domain br_default untagged 1
cumulus@switch:~$ nv config apply

Edit the /etc/network/interfaces file and add the bridge:

cumulus@switch:~$ sudo nano /etc/network/interfaces
...
auto br_default
iface br_default
    bridge-ports swp1 swp2
    bridge-vids 10 20
    bridge-pvid 1
    bridge-vlan-aware yes
...

Run the ifreload -a command to load the new configuration:

cumulus@switch:~$ ifreload -a

The Primary VLAN Identifier (PVID) of the bridge defaults to 1. You do not have to specify bridge-pvid for a bridge or a port. However, even though this does not affect the configuration, it helps other users for readability. The following configurations are identical to each other and the configuration above:

auto br_default
iface br_default
    bridge-ports swp1 swp2
    bridge-vids 1 10 20
    bridge-vlan-aware yes

auto br_default
iface br_default
    bridge-ports swp1 swp2
    bridge-pvid 1
    bridge-vids 1 10 20
    bridge-vlan-aware yes

auto br_default
iface br_default
    bridge-ports swp1 swp2
    bridge-vids 10 20
    bridge-vlan-aware yes

  • If you specify bridge-vids or bridge-pvid at the bridge level, all ports in the bridge inherit these configurations. However, specifying any of these settings for a specific port overrides the setting in the bridge.
  • Do not bridge the management port eth0 with any switch ports. For example, if you create a bridge with eth0 and swp1, the bridge does not work correctly and disrupts access to the management interface.

Configure Multiple VLAN-aware Bridges

This example shows the commands required to create two VLAN-aware bridges on the switch.

  • bridge1 bridges swp1 and swp2, and includes 2 VLANs; vlan 10 and vlan 20
  • bridge2 bridges swp3 and contains one VLAN; vlan 10

Bridges are independent so you can reuse VLANs between bridges. Each VLAN-aware bridge maintains its own MAC address and VLAN tag table; MAC and VLAN tags in one bridge are not visible to the other table.

cumulus@switch:~$ nv set interface swp1-2 bridge domain bridge1
cumulus@switch:~$ nv set bridge domain bridge1 vlan 10,20
cumulus@switch:~$ nv set bridge domain bridge1 untagged 1
cumulus@switch:~$ nv set interface swp3 bridge domain bridge2
cumulus@switch:~$ nv set bridge domain bridge2 vlan 10
cumulus@switch:~$ nv set bridge domain bridge2 untagged 1
cumulus@switch:~$ nv config apply

Edit the /etc/network/interfaces file and add the bridge:

cumulus@switch:~$ sudo nano /etc/network/interfaces
...
auto bridge1
iface bridge1
    bridge-ports swp1 swp2
    bridge-vlan-aware yes
    bridge-vids 10 20
    bridge-pvid 1

auto bridge2
iface bridge2
    bridge-ports swp3
    bridge-vlan-aware yes
    bridge-vids 10
    bridge-pvid 1
...

Run the ifreload -a command to load the new configuration:

cumulus@switch:~$ ifreload -a

NVIDIA Spectrum 1 switches support a maximum of 10000 VLAN elements. NVIDIA Spectrum-2 switches and later support a maximum of 15996 VLAN elements when warm boot mode is off or 7934 VLAN elements when warm boot mode is on. Cumulus Linux calculates the total number of VLAN elements as the number of VLANs times the number of configured bridges. For example, 6 bridges, each containing 2600 VLANs totals 15600 VLAN elements.

On NVIDIA Spectrum-2 switches and later, if you enable multiple VLAN-aware bridges and want to use more VLAN elements than the default, you must update the number of VLAN elements in the /etc/mlx/datapath/broadcast_domains.conf file.

  • To specify the total number of bridge domains you want to use, uncomment and edit the broadcast_domain.max_vlans parameter. The default value is 6143 when warm boot mode is off or 4096 when warm boot mode is on.
  • To specify the total number of subinterfaces you want to use, uncomment and edit the broadcast_domain.max_subinterfaces parameter. The default value is 3872 when warm boot mode is off or 1872 when warm boot mode is on.

You must restart switchd with the systemctl restart switchd command to apply the configuration.

The number of broadcast_domain.max_vlans plus broadcast_domain.max_subinterfaces cannot exceed 15996.

Increasing the broadcast_domain.max_vlans parameter can affect layer 2 multicast scale support.

Reserved VLAN Range

For hardware data plane internal operations, the switching silicon requires VLANs for every physical port, Linux bridge, and layer 3 subinterface. Cumulus Linux reserves a range of VLANs by default; the reserved range is 3725-3999.

If the reserved VLAN range conflicts with any user-defined VLANs, you can modify the range. The new range must be a contiguous set of VLANs with IDs between 2 and 4094. For a single VLAN-aware bridge, the minimum size of the range is 2 VLANs. For multiple VLAN-aware bridges, the minimum size of the range is the number of VLAN-aware bridges on the system plus one.

The following example changes the reserved VLAN range to be between 4064 and 4094:

cumulus@switch:~$ nv set system global reserved vlan internal range 4064-4094
cumulus@switch:~$ nv config apply

  1. Edit the /etc/cumulus/switchd.conf file to uncomment the resv_vlan_range line and specify a new range.

    cumulus@switch:~$ sudo nano /etc/cumulus/switchd.conf
...
# global reserved vlan internal range
resv_vlan_range = 4064-4094

  2. After you save the file, you must restart switchd:

    cumulus@switch:~$ sudo systemctl restart switchd.service

VLAN Pruning

By default, the bridge port inherits the bridge VIDs, however, you can configure a port to override the bridge VIDs.

This example commands configure swp3 to override the bridge VIDs:

cumulus@switch:~$ nv set interface swp1-3 bridge domain br_default
cumulus@switch:~$ nv set bridge domain br_default vlan 10,20
cumulus@switch:~$ nv set bridge domain br_default untagged 1
cumulus@switch:~$ nv set interface swp3 bridge domain br_default vlan 20
cumulus@switch:~$ nv config apply

Edit the /etc/network/interfaces file, then run the ifreload -a command. The following example commands configure swp3 to override the bridge VIDs:

cumulus@switch:~$ sudo nano /etc/network/interfaces
...
auto br_default
iface br_default
    bridge-ports swp1 swp2 swp3
    bridge-pvid 1
    bridge-vids 10 20
    bridge-vlan-aware yes

auto swp3
iface swp3
  bridge-vids 20
...

cumulus@switch:~$ ifreload -a

Access Ports and Tagged Packets

Access ports ignore all tagged packets. In the configuration below, swp1 and swp2 are access ports, while all untagged traffic goes to VLAN 10:

cumulus@switch:~$ nv set interface swp1-2 bridge domain br_default
cumulus@switch:~$ nv set bridge domain br_default vlan 10,20
cumulus@switch:~$ nv set bridge domain br_default untagged 1
cumulus@switch:~$ nv set interface swp1 bridge domain br_default access 10
cumulus@switch:~$ nv set interface swp2 bridge domain br_default access 10
cumulus@switch:~$ nv config apply

Edit the /etc/network/interfaces file, then run the ifreload -a command.

cumulus@switch:~$ sudo nano /etc/network/interfaces
...
auto br_default
iface br_default
    bridge-ports swp1 swp2
    bridge-pvid 1
    bridge-vids 10 20
    bridge-vlan-aware yes

auto swp1
iface swp1
    bridge-access 10

auto swp2
iface swp2
    bridge-access 10
...

cumulus@switch:~$ ifreload -a

Drop Untagged Frames

With VLAN-aware bridge mode, you can configure a switch port to drop any untagged frames. To do this, add bridge-allow-untagged no to the switch port (not to the bridge). The bridge port is without a PVID and drops untagged packets.

The following example command configures swp2 to drop untagged frames:

cumulus@switch:~$ nv set interface swp2 bridge domain br_default untagged none
cumulus@switch:~$ nv config apply

Edit the /etc/network/interfaces file to add the bridge-allow-untagged no line under the switch port interface stanza, then run the ifreload -a command.

cumulus@switch:~$ sudo nano /etc/network/interfaces
...
auto swp1
iface swp1

auto swp2
iface swp2
    bridge-allow-untagged no

auto br_default
iface br_default
    bridge-ports swp1 swp2
    bridge-pvid 1
    bridge-vids 10 20
    bridge-vlan-aware yes
...

cumulus@switch:~$ sudo ifreload -a

When you check VLAN membership for that port, it shows that there is no untagged VLAN.

cumulus@switch:~$ bridge -c vlan show
portvlan ids
swp1 1 PVID Egress Untagged
  10 20

swp2 10 20

bridge 1

VLAN Layer 3 Addressing

When configuring the VLAN attributes for the bridge, specify the attributes for each VLAN interface. If you are configuring the switch virtual interface (SVI) for the native VLAN, you must declare the native VLAN and specify its IP address. Specifying the IP address in the bridge stanza itself returns an error.

The following example commands declare native VLAN 10 with IPv4 address 10.1.10.2/24 and IPv6 address 2001:db8::1/32.

The NVUE and Linux commands also show an example with multiple VLAN-aware bridges.

cumulus@switch:~$ nv set interface vlan10 ip address 10.1.10.2/24
cumulus@switch:~$ nv set interface vlan10 ip address 2001:db8::1/32
cumulus@switch:~$ nv config apply

cumulus@switch:~$ nv set interface bridge2_vlan10 type svi
cumulus@switch:~$ nv set interface bridge2_vlan10 vlan 10
cumulus@switch:~$ nv set interface bridge2_vlan10 base-interface bridge2
cumulus@switch:~$ nv set interface bridge2_vlan10 ip address 10.1.10.2/24
cumulus@switch:~$ nv set interface bridge1_vlan10 type svi
cumulus@switch:~$ nv set interface bridge1_vlan10 vlan 10
cumulus@switch:~$ nv set interface bridge1_vlan10 base-interface bridge1
cumulus@switch:~$ nv set interface bridge1_vlan10 ip address 12.1.10.2/24
cumulus@switch:~$ nv config apply

Edit the /etc/network/interfaces file, then run the ifreload -a command.

cumulus@switch:~$ sudo nano /etc/network/interfaces
...
auto bridge
iface bridge
    bridge-ports swp1 swp2
    bridge-pvid 1
    bridge-vids 10 20
    bridge-vlan-aware yes
auto vlan10
iface vlan10
    address 10.1.10.2/24
    address 2001:db8::1/32
    vlan-id 10
    vlan-raw-device br_default

cumulus@switch:~$ ifreload -a

cumulus@switch:~$ sudo nano /etc/network/interfaces
...
auto bridge2_vlan10
iface bridge2_vlan10
    address 10.1.10.2/24
    hwaddress 1c:34:da:1d:e6:fd
    vlan-raw-device bridge2
    vlan-id 10

auto bridge1_vlan10
iface bridge1_vlan10
address 12.1.10.2/24
hwaddress 1c:34:da:1d:e6:fd
vlan-raw-device bridge1
vlan-id 10

The first time you configure a switch, all southbound bridge ports are down; therefore, by default, the SVI is also down. You can force the SVI to always be up by disabling interface state tracking so that the SVI is always in the UP state, even if all member ports are down. Other implementations describe this feature as no autostate. This is beneficial if you want to perform connectivity testing.

To keep the SVI perpetually UP, create a dummy interface, then make the dummy interface a member of the bridge.

▼ Example Configuration

By default, Cumulus Linux automatically generates IPv6 link-local addresses on VLAN interfaces. If you want to use a different mechanism to assign link-local addresses, you can disable this feature. You can disable link-local automatic address generation for both regular IPv6 addresses and address-virtual (macvlan) addresses.

To disable automatic address generation for a regular IPv6 address on a VLAN, run the following command. The following example command disables automatic address generation for a regular IPv6 address on VLAN 10.

Cumulus Linux does not provide NVUE commands for this setting.

Edit the /etc/network/interfaces file to add the line ipv6-addrgen off to the VLAN stanza, then run the ifreload -a command.

cumulus@switch:~$ sudo nano /etc/network/interfaces
...
auto vlan10
iface vlan 10
    ipv6-addrgen off
    vlan-id 10
    vlan-raw-device br_default
...

cumulus@switch:~$ ifreload -a

To reenable automatic link-local address generation for a VLAN:

Cumulus Linux does not provide NVUE commands for this setting.
Edit the /etc/network/interfaces file to remove the line ipv6-addrgen off from the VLAN stanza, then run the ifreload -a command.

Static MAC Address Entries

You can add a static MAC address entry to the layer 2 table for an interface within the VLAN-aware bridge by running a command similar to the following:

cumulus@switch:~$ sudo bridge fdb add 12:34:56:12:34:56 dev swp1 vlan 150 master static sticky
cumulus@switch:~$ sudo bridge fdb show
44:38:39:00:00:7c dev swp1 master bridge permanent
12:34:56:12:34:56 dev swp1 vlan 150 sticky master bridge static
44:38:39:00:00:7c dev swp1 self permanent
12:12:12:12:12:12 dev swp1 self permanent
12:34:12:34:12:34 dev swp1 self permanent
12:34:56:12:34:56 dev swp1 self permanent
12:34:12:34:12:34 dev bridge master bridge permanent
44:38:39:00:00:7c dev bridge vlan 500 master bridge permanent
12:12:12:12:12:12 dev bridge master bridge permanent

Example Configuration

The following example configuration contains an access port (swp51), a trunk carrying all VLANs (swp3 thru swp48), and a trunk pruning some VLANs from a switch port (swp2).

cumulus@switch:mgmt:~$ nv set interface swp3-48 bridge domain br_default
cumulus@switch:mgmt:~$ nv set bridge domain br_default vlan 310,700,707,712,850,910
cumulus@switch:mgmt:~$ nv set interface swp1 bridge domain br_default access 310
cumulus@switch:mgmt:~$ nv set interface swp1 bridge domain br_default stp bpdu-guard on
cumulus@switch:mgmt:~$ nv set interface swp1 bridge domain br_default stp admin-edge on
cumulus@switch:mgmt:~$ nv set interface swp2 bridge domain br_default vlan 707,712,850
cumulus@switch:mgmt:~$ nv set interface swp2 bridge domain br_default stp admin-edge on
cumulus@switch:mgmt:~$ nv set interface swp2 bridge domain br_default stp bpdu-guard on
cumulus@switch:mgmt:~$ nv set interface swp49 bridge domain br_default stp network on
cumulus@switch:mgmt:~$ nv set interface swp50 bridge domain br_default stp network on
cumulus@switch:mgmt:~$ nv config apply

cumulus@switch:mgmt:~$ sudo cat /etc/nvue.d/startup.yaml
- set:
    bridge:
      domain:
        br_default:
          vlan:
            '310': {}
            '700': {}
            '707': {}
            '712': {}
            '850': {}
            '910': {}
    interface:
      swp1:
        bridge:
          domain:
            br_default:
              access: 310
              stp:
                admin-edge: on
                bpdu-guard: on
        type: swp
      swp2:
        bridge:
          domain:
            br_default:
              stp:
                admin-edge: on
                bpdu-guard: on
              vlan:
                '707': {}
                '712': {}
                '850': {}
        type: swp
      ...  
      swp49:
        bridge:
          domain:
            br_default:
              stp:
                network: on
        type: swp
      swp50:
        bridge:
          domain:
            br_default:
              stp:
                network: on
        type: swp
    system:
      hostname: switch

cumulus@switch:mgmt:~$ sudo cat /etc/network/interfaces
...
auto lo
iface lo inet loopback

auto mgmt
iface mgmt
    address 127.0.0.1/8
    address ::1/128
    vrf-table auto

auto eth0
iface eth0 inet dhcp
    ip-forward off
    ip6-forward off
    vrf mgmt

# the following is an access port

auto swp1
iface swp1
    bridge-access 310
    mstpctl-bpduguard yes
    mstpctl-portadminedge yes

# the following is a trunk port that is pruned
# only .1q tags of 707, 712, 850 are sent and received

auto swp2
iface swp2
    bridge-vids 707 712 850
    mstpctl-bpduguard yes
    mstpctl-portadminedge yes
...
# the following port is the trunk uplink and inherits all vlans
# from br_default; bridge assurance is enabled using portnetwork

auto swp49
iface swp49
    mstpctl-portnetwork yes

# the following port is the trunk uplink and inherits all vlans
# from 'br_default'; bridge assurance is enabled using portnetwork

auto swp50
iface swp50
    mstpctl-portnetwork yes

# ports swp3-swp48 are trunk ports that inherit vlans 
# 310,700,707,712,850,910 from the bridge br_default

auto br_default
iface br_default
    bridge-ports swp1 swp2 swp3... swp49 swp50
    hwaddress 44:38:39:22:01:af
    bridge-vlan-aware yes
    bridge-vids 310 700 707 712 850 910
    bridge-pvid 1

Considerations

Spanning Tree Protocol (STP)

VLAN Translation

You cannot enable VLAN translation on a bridge in VLAN-aware mode. Only traditional mode bridges support VLAN translation.

Bridge Conversion

You cannot convert traditional mode bridges automatically to and from a VLAN-aware bridge. You must delete the original configuration and bring down all member switch ports before creating a new bridge.

    Copyright © 2024  NVIDIA Corporation