layout-3 layout-6 layout-1 layout-top
NVIDIA Docs Hubchevron_right NVIDIA Networkingchevron_right Networking Softwarechevron_right Switch Softwarechevron_right

Cumulus Linux

layout-top layout-6 layout-1

If you are using the current version of Cumulus Linux, the content on this page may not be up to date. The current version of the documentation is available here. If you are redirected to the main page of the user guide, then this page may have been renamed; please search for it there.

Route Filtering and Redistribution

Route filtering lets you exclude routes that neighbors advertise or receive. You can use route filtering to manipulate traffic flows, reduce memory utilization, and improve security.

This section discusses the following route filtering methods:

  • Prefix lists
  • Route maps
  • Route redistribution

Route map and prefix list names must start with a letter and can contain letters, digits, underscores and dashes. For example, you can name a route map MAP10 or ROUTE-MAP_10 but you cannot name a route map 10 or 10_ROUTE-MAP.

Prefix Lists

Prefix lists are access lists for route advertisements that match routes instead of traffic. Prefix lists are typically used with route maps and other filtering methods. A prefix list can match the prefix (the network itself) and the prefix length (the length of the subnet mask).

The following example commands configure a prefix list that permits all prefixes in the range 10.0.0.0/16 with a subnet mask less than or equal to /30. For networks 10.0.0.0/24, 10.10.10.0/24, and 10.0.0.10/32, only 10.0.0.0/24 matches (10.10.10.0/24 has a different prefix and 10.0.0.10/32 has a greater subnet mask).

cumulus@switch:~$ nv set router policy prefix-list prefixlist1 rule 1 match 10.0.0.0/16 max-prefix-len 30
cumulus@switch:~$ nv set router policy prefix-list prefixlist1 rule 1 action permit
cumulus@switch:~$ nv config apply

For IPv6, you need to run an additional command to set the prefix list type to IPv6. For example:

cumulus@switch:~$ nv set router policy prefix-list prefixlistipv6 type ipv6
cumulus@switch:~$ nv set router policy prefix-list prefixlistipv6 rule 1 match 2001:100::1/64
cumulus@switch:~$ nv set router policy prefix-list prefixlistipv6 rule 1 action permit 
cumulus@switch:~$ nv config apply

cumulus@switch:~$ sudo vtysh
switch# configure terminal
switch(config)# ip prefix-list prefixlist1 seq 1 permit 10.0.0.0/16 le 30
switch(config)# exit
switch# write memory
switch# exit
cumulus@switch:~$

The vtysh commands save the configuration in the /etc/frr/frr.conf file. For example:

cumulus@switch:~$ sudo cat /etc/frr/frr.conf
...
router ospf
 ospf router-id 10.10.10.1
 timers throttle spf 80 100 6000
 passive-interface vlan10
 passive-interface vlan20
ip prefix-list prefixlist1 seq 1 permit 10.0.0.0/16 le 30

To use this prefix list in a route map called MAP1:

cumulus@switch:~$ nv set router policy route-map MAP1 rule 10 action permit
cumulus@switch:~$ nv set router policy route-map MAP1 rule 10 match type ipv4
cumulus@switch:~$ nv set router policy route-map MAP1 rule 10 match ip-prefix-list prefixlist1
cumulus@switch:~$ nv config apply

cumulus@switch:~$ sudo vtysh
switch# configure terminal
switch(config)# route-map MAP1 permit 10
switch(config-route-map)# match ip address prefix-list prefixlist1
switch(config-route-map)# exit
switch# write memory
switch# exit
cumulus@switch:~$

The vtysh commands save the configuration in the /etc/frr/frr.conf file. For example:

cumulus@switch:~$ sudo cat /etc/frr/frr.conf
...
ip prefix-list prefixlist1 seq 1 permit 10.0.0.0/16 le 30
route-map MAP1 permit 10
match ip address prefix-list prefixlist1

Route Maps

Route maps are routing policies that Cumulus Linux considers before the router examines the forwarding table. Each statement in a route map has a sequence number, and includes a series of match and set statements. The route map parses from the lowest sequence number to the highest, and stops when there is a match.

Configure a Route Map

The following example commands configure a route map that sets the metric to 50 for interface swp51:

cumulus@switch:~$ nv set router policy route-map routemap1 rule 10 match interface swp51
cumulus@switch:~$ nv set router policy route-map routemap1 rule 10 set metric 50
cumulus@switch:~$ nv set router policy route-map routemap1 rule 10 action permit
cumulus@switch:~$ nv config apply

cumulus@switch:~$ sudo vtysh
switch# configure terminal
switch(config)# route-map routemap1 permit 10
switch(config-route-map)# match interface swp51
switch(config-route-map)# set metric 50
switch(config-route-map)# end
switch# write memory
switch# exit
cumulus@switch:~$

The vtysh commands save the configuration in the /etc/frr/frr.conf file. For example:

cumulus@switch:~$ sudo cat /etc/frr/frr.conf
...
route-map routemap1 permit 10
 match interface swp51
 set metric 50

Apply a Route Map

To apply the route map, you specify the routing protocol and the route map name.

For BGP, you can also apply a route map on route updates from BGP to Zebra. You can match on prefix, next hop, communities, and so on. You can set the metric and next hop only. Route maps do not affect the BGP internal RIB. You can use both IPv4 and IPv6 address families. Route maps work on multi-paths; however, BGP bases the metric setting on the best path only.

To apply a route map to filter route updates from BGP into Zebra, run the following command:

cumulus@switch:$ nv set vrf default router bgp address-family ipv4-unicast rib-filter routemap1
cumulus@switch:$ nv config apply

To apply an outbound route map to a route reflector client, you must run the NVUE nv set vrf <vrf> router bgp route-reflection outbound-policy on command or the vtysh neighbor <neighbor> route-map SET_IBGP_ORIG out command under the address family, before you apply the route map.

Route Redistribution

Route redistribution allows a network to use a routing protocol to route traffic dynamically based on the information learned from a different routing protocol or from static routes. Route redistribution helps increase accessibility within networks.

The following example commands redistribute routing information from OSPF routes into BGP:

cumulus@switch:~$ nv set vrf default router bgp address-family ipv4-unicast redistribute ospf
cumulus@switch:~$ nv config apply

cumulus@switch:~$ sudo vtysh
switch# configure terminal
switch(config)# router bgp
switch(config-router)# redistribute ospf
switch(config-router)# end
switch# write memory
switch# exit
cumulus@switch:~$

To redistribute all directly connected networks, use the redistribute connected command. For example:

cumulus@switch:~$ nv set vrf default router bgp address-family ipv4-unicast redistribute connected
cumulus@switch:~$ nv config apply

cumulus@switch:~$ sudo vtysh
switch# configure terminal
switch(config)# router bgp
switch(config-router)# redistribute connected
switch(config-router)# end
switch# write memory
switch# exit
cumulus@switch:~$

For OSPF, redistribution loads the database unnecessarily with type-5 LSAs. Only use this method to generate real external prefixes (type-5 LSAs).

Configuration Examples

This section shows the /etc/frr/frr.conf file configuration for example route filters and redistribution.

The following example filters all routes that are not originated in the local AS:

...
router bgp 65101
 bgp router-id 10.10.10.1
 neighbor underlay interface remote-as external
 !
 address-family ipv4 unicast
  neighbor underlay route-map my-as out
 exit-address-family
!
bgp as-path access-list my-as permit ^$
!
route-map my-as permit 10
 match as-path my-as
!
route-map my-as deny 20
!

The following example sets communities based on prefix-lists:

...
router bgp 65101
 bgp router-id 10.10.10.1
 neighbor underlay interface remote-as external
 !
 address-family ipv6 unicast
  neighbor underlay activate
  neighbor underlay route-map MARK-PREFIXES out
 exit-address-family
!
ipv6 prefix-list LOW-PRIO seq 5 permit 2001:db8:dead::/56 le 64
ipv6 prefix-list MID-PRIO seq 5 permit 2001:db8:beef::/56 le 64
ipv6 prefix-list HI-PRIO seq 5 permit 2001:db8:cafe::/56 le 64
!
route-map MARK-PREFIXES permit 10
 match ipv6 address prefix-list LOW-PRIO
 set community 123:200
!
route-map MARK-PREFIXES permit 20
 match ipv6 address prefix-list MID-PRIO
 set community 123:500
!
route-map MARK-PREFIXES permit 30
 match ipv6 address prefix-list HI-PRIO
 set community 123:1000
!

The following example filters routes from advertising to the peer:

router bgp 65101
 bgp router-id 10.10.10.1
 neighbor underlay interface remote-as external
 !
 address-family ipv4 unicast
  neighbor underlay route-map POLICY-OUT out
 exit-address-family
!
ip prefix-list BLOCK-RFC1918 seq 5 permit 10.0.0.0/8 le 24
ip prefix-list BLOCK-RFC1918 seq 10 permit 172.16.0.0/12 le 24
ip prefix-list BLOCK-RFC1918 seq 15 permit 192.168.0.0/16 le 24
ip prefix-list ADD-COMM-OUT seq 5 permit 100.64.0.0/10 le 24
ip prefix-list ADD-COMM-OUT seq 10 permit 192.0.2.0/24
!
route-map POLICY-OUT deny 10
 match ip address prefix-list BLOCK-RFC1918
!
route-map POLICY-OUT permit 20
 match ip address prefix-list ADD-COMM-OUT
 set community 123:1000
!
route-map POLICY-OUT permit 30

The following example sets mutual redistribution between OSPF and BGP (filters by route tags):

...
router ospf
  redistribute bgp route-map BGP-INTO-OSPF
!
router bgp 65101
 bgp router-id 10.10.10.1
 neighbor underlay interface remote-as external
 !
 address-family ipv4 unicast
  redistribute ospf route-map OSPF-INTO-BGP
 exit-address-family
!
route-map OSPF-INTO-BGP deny 10
 match tag 4271
!
route-map OSPF-INTO-BGP permit 20
 set tag 2328
!
route-map BGP-INTO-OSPF deny 10
 match tag 2328
!
route-map BGP-INTO-OSPF permit 20
 set tag 4271

The following example filters and modifies redistributed routes:

...
router ospf
  redistribute bgp route-map EXTERNAL-2-1K
!
route-map EXTERNAL-2-1K permit 10
 set metric 1000
 set metric-type type-1

Considerations

When you configure a route map to match a prefix list, community list, or aspath list, the permit or deny actions in the list determine the criteria to evaluate in each route map sequence; for example:

  • If you match a list in a route map permit sequence, Cumulus Linux matches the permitted routes in the list for that route map sequence and the policy permits them. Denied routes in the list do not match and Cumulus Linux evaluates them in later route map sequences.
  • If you match a list in a route map deny sequence, Cumulus Linux matches the permitted routes in the list for that route map sequence and the policy denies them. Denied routes in the list do not match and Cumulus Linux evaluates them in later route map sequences.

NVIDIA recommends you always configure a community list as permit, and permit or deny routes using route map sequences.

    Copyright © 2024  NVIDIA Corporation