layout-3 layout-6 layout-1 layout-top
NVIDIA Docs Hubchevron_right NVIDIA Networkingchevron_right Networking Softwarechevron_right Switch Softwarechevron_right

Cumulus Linux

layout-top layout-6 layout-1

If you are using the current version of Cumulus Linux, the content on this page may not be up to date. The current version of the documentation is available here. If you are redirected to the main page of the user guide, then this page may have been renamed; please search for it there.

LACP Bypass

On Cumulus Linux, LACP bypass allows a bond configured in 802.3ad mode to become active and forward traffic even when there is no LACP partner. For example, you can enable a host that does not have the capability to run LACP to PXE boot while connected to a switch on a bond configured in 802.3ad mode. After the pre-boot process completes and the host is capable of running LACP, the normal 802.3ad link aggregation operation takes over.

LACP Bypass All-active Mode

In all-active mode, when a bond has multiple slave interfaces, each bond slave interface operates as an active link while the bond is in bypass mode. This is useful during PXE boot of a server with multiple NICs, when you cannot determine beforehand which port needs to be active.

  • All-active mode is not supported on bonds that are not specified as bridge ports on the switch.
  • STP does not run on the individual bond slave interfaces when the LACP bond is in all-active mode. Only use all-active mode on host-facing LACP bonds. Configure STP BPDU guard together with all-active mode.
  • In an MLAG deployment where bond slaves of a host are connected to two switches and the bond is in all-active mode, all the slaves of bond are active on both the primary and secondary MLAG nodes.
  • LACP bypass is supported with EVPN multihoming.
  • priority mode, bond-lacp-bypass-period, bond-lacp-bypass-priority, and bond-lacp-bypass-all-active are not supported.

Configure LACP Bypass

To enable LACP bypass on the host-facing bond:

The following commands create a VLAN-aware bridge with LACP bypass enabled:

cumulus@switch:~$ net add bond bond1 bond slaves swp51s2,swp51s3
cumulus@switch:~$ net add bond bond1 clag id 1
cumulus@switch:~$ net add bond bond1 bond lacp-bypass-allow
cumulus@switch:~$ net add bond bond1 stp bpduguard
cumulus@switch:~$ net add bridge bridge ports bond1,bond2,bond3,bond4,bond5
cumulus@switch:~$ net add bridge bridge vids 100-105
cumulus@switch:~$ net pending
cumulus@switch:~$ net commit

Edit the /etc/network/interfaces file to add the set bond-lacp-bypass-allow to yes option, then run the ifreload -a command. The following configuration creates a VLAN-aware bridge with LACP bypass enabled:

cumulus@switch:~$ sudo nano /etc/network/interfaces
...
auto bond1
iface bond1
    bond-lacp-bypass-allow yes
    bond-slaves swp51s2 swp51s3
    clag-id 1
    mstpctl-bpduguard yes
...
auto bridge
iface bridge
    bridge-ports bond1 bond2 bond3 bond4 peer5
    bridge-vids 100-105
    bridge-vlan-aware yes
...

cumulus@switch:~$ sudo ifreload -a

cumulus@switch:~$ cl set interface bond1 bond member swp51s2,swp51s3
cumulus@switch:~$ cl set interface bond1 bond mlag id 1
cumulus@switch:~$ cl set interface bond1 bond lacp-bypass on
cumulus@switch:~$ cl set interface bond1,bond2,bond3,bond4,bond5 bridge domain bridge vlan 100-105
cumulus@switch:~$ cl set interface bond1 bridge domain bridge stp bpdu-guard on
cumulus@switch:~$ cl config apply

To check the status of the configuration, run the following commands.

Run the net show interface <bond> command on the bond and its slave interfaces:

cumulus@switch:~$ net show interface bond1

    Name   MAC               Speed   MTU   Mode
--  ------ ----------------- ------- ----- ----------
UP  bond1  44:38:39:00:00:5b 1G      1500  Bond/Trunk

Bond Details
------------------ -------------------------
Bond Mode:         LACP
Load Balancing:    Layer3+4
Minimum Links:     1
In CLAG:           CLAG Active
LACP Sys Priority:
LACP Rate:         Fast Timeout
LACP Bypass:       LACP Bypass Not Supported

    Port       Speed     TX   RX   Err   Link Failures
-- --------   ------- ---- ---- ----- ---------------
UP swp51s2(P) 1G         0    0     0               0
UP swp51s3(P) 1G         0    0     0               0


All VLANs on L2 Port
----------------------
100-105

Untagged
----------
1

Vlans in disabled State
-------------------------
100-105

LLDP
--------   ---- ------------------
swp51s2(P) ==== swp1(spine01)
swp51s3(P) ==== swp1(spine02)

Run the ip link show command on the bond and its slave interfaces:

cumulus@switch:~$ ip link show bond1
164: bond1: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue master br0 state UP mode DORMANT group default
    link/ether c4:54:44:f6:44:5a brd ff:ff:ff:ff:ff:ff
cumulus@switch:~$ ip link show swp51s2
55: swp51s2: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bond1 state UP mode DEFAULT group default qlen 1000
    link/ether c4:54:44:f6:44:5a brd ff:ff:ff:ff:ff:ff
cumulus@switch:~$ ip link show swp52s3
56: swp51s3: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bond1 state UP mode DEFAULT group default qlen 1000
    link/ether c4:54:44:f6:44:5a brd ff:ff:ff:ff:ff:ff

cumulus@switch:~$ cl show interface bond1

To verify that LACP bypass is enabled on a bond and its slave interfaces, use the cat command:

cumulus@switch:~$ cat /sys/class/net/bond1/bonding/lacp_bypass
on 1
cumulus@switch:~$ cat /sys/class/net/bond1/bonding/slaves
swp51 swp52
cumulus@switch:~$ cat /sys/class/net/swp52/bonding_slave/ad_rx_bypass
1
cumulus@switch:~$ cat /sys/class/net/swp51/bonding_slave/ad_rx_bypass
1

Example LACP Bypass Configuration

The following configuration shows LACP bypass enabled for multiple active interfaces (all-active mode) with a bridge in traditional bridge mode:

...
auto bond1
iface bond1
    bond-slaves swp3 swp4
    bond-lacp-bypass-allow 1

auto br0
iface br0
    bridge-ports bond1 bond2 bond3 bond4 peer5
    mstpctl-bpduguard bond1=yes
...

    Copyright © 2024  NVIDIA Corporation