SyncE

SyncE is a standard for transmitting clock signals over the Ethernet physical layer to synchronize clocks across the network by propagating frequency using the transmission rate of symbols in the network. A dedicated Ethernet channel manages this synchronization.

The Cumulus Linux switch includes a SyncE controller and a SyncE daemon.

• The SyncE controller reads performance counters to calculate the differences between transmit and receive ethernet symbols on the physical layer to fine tune the clock frequency.
• The SyncE daemon (synced):
  • Manages transmitting and receiving SSMs on all SyncE enabled ports using the Ethernet Synchronization Messaging Channel (ESMC).
  • Manages the synchronization hierarchy and runs the master selection algorithm to choose the best reference clock from the QL in the SSM.

Basic Configuration

Basic SyncE configuration requires you:

• Enable SyncE on the switch.
• Configure SyncE on at least one interface so that the interface is a timing source that passes to the selection algorithm.

The basic configuration shown below uses the default SyncE settings:

• The frequency source priority on the interface is set to 100.
• The amount of time SyncE waits after the interface comes up before using the interface for synchronization is set to 5 minutes.

cumulus@switch:~$ nv set service synce enable on
cumulus@switch:~$ nv set interface swp2 synce enable on
cumulus@switch:~$ nv config apply

cumulus@switch:~$ sudo nano /etc/synced/synced.conf
...
[global]
twtr_seconds=10
priority=1
loglevel=info

[swp1]

[swp3]

[swp4]
priority=4

cumulus@switch:~$ sudo systemctl enable synced.service
cumulus@switch:~$ sudo systemctl start synced.service

Optional Global Configuration

Wait to Restore Time

The wait to restore time is the number of seconds SyncE waits for each port to be up before opening the Ethernet Synchronization Message Channel (ESMC) for messages. You can set a value betwen 0 and 720 (12) minutes. The default value is 300 seconds (5 minutes).

The following command example sets the wait to restore time to 180 seconds (3 minutes):

cumulus@switch:~$ nv set service synce wait-to-restore-time 180
cumulus@switch:~$ nv config apply

cumulus@switch:~$ sudo nano /etc/synced/synced.conf
...
[global]
twtr_seconds=180

cumulus@switch:~$ sudo systemctl restart synced.service

Priority

You can set the priority for the clock source. The lowest priority is 1 and the highest priority is 256. If two clock sources have the same priority, the switch uses the lowest clock source.

The following example command sets the priority to 256:

cumulus@switch:~$ nv set service synce provider-default-priority 256
cumulus@switch:~$ nv config apply

cumulus@switch:~$ sudo nano /etc/synced/synced.conf
...
[global]
twtr_seconds=180
priority=256

cumulus@switch:~$ sudo systemctl restart synced.service

Logging

You can set the logging level that the SyncE service uses:

• critical level logs critical errors and notices.
• debug level logs fine-grained informational events that are most useful to debug an application.
• error level logs errors.
• info level logs informational messages.
• notice level logs notices.

The following example command sets the logging level to debug.

cumulus@switch:~$ nv set service synce log-level debug
cumulus@switch:~$ nv config apply

cumulus@switch:~$ sudo nano /etc/synced/synced.conf
...
[global]
twtr_seconds=180
priority=256
loglevel=debug

cumulus@switch:~$ sudo systemctl reload synced.service

Optional Interface Configuration

Frequency Source Priority

The clock selection algorithm uses the frequency source priority on an interface to choose between two sources that have the same QL. You can specify a value between 1 (the highest priority) and 256 (the lowest priority). The default value is 1.

The following command example sets the priority on swp2 to 10, on swp2 to 20, and on swp3 to 10:

cumulus@switch:~$ nv set interface swp1 synce provider-priority 10
cumulus@switch:~$ nv set interface swp2 synce provider-priority 20
cumulus@switch:~$ nv set interface swp3 synce provider-priority 10
cumulus@switch:~$ nv config apply

cumulus@switch:~$ sudo nano /etc/synced/synced.conf
...
[global]
twtr_seconds=180
priority=256
log-level=debug

[swp1]
priority=10
 
[swp2]
priority=20
 
[swp3]
priority=10

cumulus@switch:~$ sudo systemctl restart synced.service

Troubleshooting

Show SyncE Configuration and Counters

To show global SyncE configuration, run the NVUE nv show service synce command or the Linux syncectl show status command.

To show SyncE configuration for a specific interface, run the NVUE nv show interface <interface-id> synce command or the Linux syncectl show interface status <interface> command.

cumulus@switch:~$ nv show service synce
                           operational                                                        applied
-------------------------  -----------------------------------------------------------------  -------
enable                     On                                                                 on
log-level                  notice
provider-default-priority  10                                                                 10
wait-to-restore-time       40                                                                 40
clock-identity             0x849e00fffe00ca00
local-clock-quality        eec1
network-type               1
summary                    Group #0: TRACKING holdover acquired on swp1. freq_diff: 77 (ppb)

To show SyncE statistics for a specific interface, run the NVUE nv show interface <interface-id> synce counters command or the Linux syncectl show interface counters <interface command:

cumulus@switch:~$ nv show interface swp2 synce counters
                 operational  applied
---------------  -----------  -------
rx-esmc          248899
rx-esmc-dnu      0
rx-esmc-e-eec    0
rx-esmc-e-prc    241259
rx-esmc-e-prtc   0
rx-esmc-eec1     0
rx-esmc-error    0
rx-esmc-prc      4125
rx-esmc-prtc     0
rx-esmc-ssu-a    0
rx-esmc-ssu-b    0
rx-esmc-unknown  3515
tx-esmc          249107
tx-esmc-dnu      245111
tx-esmc-e-eec    0
tx-esmc-e-prc    107
tx-esmc-e-prtc   0
tx-esmc-eec1     2488
tx-esmc-error    4
tx-esmc-prc      1401
tx-esmc-prtc     0
tx-esmc-ssu-a    0
tx-esmc-ssu-b    0
tx-esmc-unknown  0

Clear SyncE Interface Counters

To clear counters for a specific SyncE interface, run the NVUE nv action clear interface <interface> synce counters command or the Linux syncectl clear interface counters <interface> command.

cumulus@switch:~$ nv action clear interface swp1 synce counters
swp1 counters cleared
Action succeeded

To clear counters for all SyncE interfaces, run the syncectl clear counters command.

To see all the syncectl commands, run syncectl -h.

Related Information