layout-3 layout-6 layout-1 layout-top
NVIDIA Docs Hubchevron_right NVIDIA Networkingchevron_right Networking Softwarechevron_right Switch Softwarechevron_right

Cumulus Linux

layout-top layout-6 layout-1

Neighbor Discovery - ND

ND allows different devices on the same link to advertise their existence to their neighbors and to learn about the existence of their neighbors. ND is the IPv6 equivalent of IPv4 ARP for layer 2 address resolution.

ND is on by default. Cumulus Linux provides a set of configuration options to support IPv6 networks and adjust your security settings.

Cumulus Linux provides options to configure:

  • Router Advertisement
  • IPv6 prefixes
  • Recursive DNS servers
  • DNS Search Lists
  • Home Agents
  • MTU for neighbor discovery messages
  • Global timer settings

Router Advertisement

Router Advertisement is disabled by default. To enable Router Advertisment for an interface:

cumulus@leaf01:mgmt:~$ nv set interface swp1 ip neighbor-discovery router-advertisement enable on
cumulus@leaf01:mgmt:~$ nv config apply

cumulus@leaf01:mgmt:~$ sudo vtysh
...
leaf01# configure terminal
leaf01(config)# interface swp1
leaf01(config-if)# no ipv6 nd suppress-ra

For Stateless Address Auto-Configuration (SLAAC), Router Advertisment must be enabled on the interface. The prefix advertised in Router Advertisement must belong to the /64 subnet.

You can configure these optional settings:

  • Allow consecutive Router Advertisement packets to transmit more frequently than every three seconds (fast retransmit). You can set this parameter to on or off. The default setting is on.
  • Set the hop limit value advertised in a Router Advertisement message. You can set a value between 0 and 255. The default value is 64.
  • Set the interval between unsolicited multicast router advertisements from the interface. You can set a value between 70 and 1800000 miliseconds. The default value is 600000 miliseconds.
  • Set the maximum amount of time that Router Advertisement messages can exist on the route. You can set a value between 0 and 9000 seconds. The default value is 1800.
  • Allow a dynamic host to use a managed protocol, such as DHCPv6 to configure IP addresses automatically (managed configuration). Set this parameter to on or off. By default, this parameter is not set.
  • Allow a dynamic host to use a managed protocol to configure additional information through DHCPv6. Set this parameter to on or off. By default, this parameter is not set.
  • Set the amount of time that an IPv6 node is reachable. You can set a value between 0 and 3600000 milliseconds. The default value is 0.
  • Set the interval at which neighbor solicitation messages retransmit. You can set a value between 0 and 4294967295 milliseconds. The default value is 0.
  • Allow hosts to use router preference to select the default router. You can set a value of high, medium, or low. The default value is medium.

The following example commands set:

  • The Router Advertisement interval to 60000 milliseconds (60 seconds).
  • The router preference to high.
  • The amount of time that an IPv6 node is reachable to 3600000.
  • The interval at which neighbor solicitation messages retransmit to 4294967295.
  • The hop limit value in the Router Advertisement message to 100.
  • The maximum amount of time that Router Advertisement messages exist on the route to 4000.
cumulus@leaf01:mgmt:~$ nv set interface swp1 ip neighbor-discovery router-advertisement interval 60000
cumulus@leaf01:mgmt:~$ nv set interface swp1 ip neighbor-discovery router-advertisement router-preference high
cumulus@leaf01:mgmt:~$ nv set interface swp1 ip neighbor-discovery router-advertisement reachable-time 3600000
cumulus@leaf01:mgmt:~$ nv set interface swp1 ip neighbor-discovery router-advertisement retransmit-time 4294967295
cumulus@leaf01:mgmt:~$ nv set interface swp1 ip neighbor-discovery router-advertisement hop-limit 100
cumulus@leaf01:mgmt:~$ nv set interface swp1 ip neighbor-discovery router-advertisement lifetime 4000
cumulus@leaf01:mgmt:~$ nv config apply

cumulus@leaf01:mgmt:~$ sudo vtysh
...
leaf01# configure terminal
leaf01(config)# interface swp1
leaf01(config-if)# ipv6 nd ra-interval 60
leaf01(config-if)# ipv6 nd router-preference high
leaf01(config-if)# ipv6 nd reachable-time 3600000
leaf01(config-if)# ipv6 nd ra-retrans-interval 4294967295
leaf01(config-if)# ipv6 nd ra-hop-limit 100
leaf01(config-if)# ipv6 nd ra-lifetime 4000
leaf01(config-if)# end
leaf01# write memory
leaf01# exit
cumulus@leaf01:mgmt:~$

The vtysh commands save the configuration in the etc/frr/frr.conf file:

cumulus@leaf01:mgmt:~$ sudo cat etc/frr/frr.conf
...
interface swp1
 ipv6 nd ra-hop-limit 100
 ipv6 nd ra-interval 60
 ipv6 nd ra-lifetime 4000
 ipv6 nd ra-retrans-interval 4294967295
 ipv6 nd reachable-time 3600000
 ipv6 nd router-preference high

The following example commands set fast retransmit to off and managed configuration to on:

cumulus@leaf01:mgmt:~$ nv set interface swp1 ip neighbor-discovery router-advertisement fast-retransmit off
cumulus@leaf01:mgmt:~$ nv set interface swp1 ip neighbor-discovery router-advertisement managed-config on
cumulus@leaf01:mgmt:~$ nv config apply

cumulus@leaf01:mgmt:~$ sudo vtysh
...
leaf01# configure terminal
leaf01(config)# interface swp1
leaf01(config-if)# ipv6 nd ra-fast-retrans
leaf01(config-if)# ipv6 nd managed-config-flag
leaf01(config-if)# end
leaf01# write memory
leaf01# exit
cumulus@leaf01:mgmt:~$

The vtysh commands save the configuration in the etc/frr/frr.conf file:

cumulus@leaf01:mgmt:~$ sudo cat etc/frr/frr.conf
...
interface swp1
 ipv6 nd ra-fast-retrans
 ipv6 nd managed-config-flag

IPv6 Prefixes

To configure IPv6 prefixes, you must specify the IPv6 prefixes you want to include in router advertisements. In addition, you can configure these optional settings:

  • Set the amount of time that the prefix is valid for on-link determination. You can set a value between 0 and 4294967295 seconds. The default value is 2592000.
  • Set the amount of time that addresses generated from a prefix remain preferred. You can set a value between 0 and 4294967295 seconds. The default value is 604800.
  • Enable adverisement to make no statement about prefix on-link or off-link properties. By default, this setting is off.
  • Enable the specified prefix to use IPv6 autoconfiguration. By default, this setting is on.
  • Indicate to hosts on the local link that the specified prefix contains a complete IP address by setting the R flag. By default, this setting is off.

The following example commands set the IPv6 prefix to 2001:db8:1::100/32, the amount of time that the prefix is valid for on-link determination to 2000000000, and the amount of time that addresses generated from a prefix remain preferred to 1000000000.

cumulus@leaf01:mgmt:~$ nv set interface swp1 ip neighbor-discovery prefix 2001:db8:1::100/32 valid-lifetime 2000000000
cumulus@leaf01:mgmt:~$ nv set interface swp1 ip neighbor-discovery prefix 2001:db8:1::100/32 preferred-lifetime 1000000000
cumulus@leaf01:mgmt:~$ nv config apply

cumulus@leaf01:mgmt:~$ sudo vtysh
...
leaf01# configure terminal
leaf01(config)# interface swp1
leaf01(config-if)# ipv6 nd prefix 2001:db8:1::100/32 2000000000 1000000000
leaf01(config-if)# end
leaf01# write memory
leaf01# exit
cumulus@leaf01:mgmt:~$

The vtysh commands write to the /etc/frr/frr.conf file:

cumulus@leaf01:mgmt:~$ sudo cat /etc/frr/frr.conf
...
interface swp1
 ipv6 nd prefix 2001:db8::/32 2000000000 1000000000
 ...

The following example commands set advertisement to make no statement about prefix on-link or off-link properties, enable the specified prefix to use IPv6 autoconfiguration, and indicate to hosts on the local link that the specified prefix contains a complete IP address.

cumulus@leaf01:mgmt:~$ nv set interface swp1 ip neighbor-discovery prefix 2001:db8:1::100/32 off-link on
cumulus@leaf01:mgmt:~$ nv set interface swp1 ip neighbor-discovery prefix 2001:db8:1::100/32 autoconfig on
cumulus@leaf01:mgmt:~$ nv set interface swp1 ip neighbor-discovery prefix 2001:db8:1::100/32 router-address on
cumulus@leaf01:mgmt:~$ nv config apply

cumulus@leaf01:mgmt:~$ sudo vtysh
...
leaf01# configure terminal
leaf01(config)# interface swp1
leaf01(config-if)# ipv6 nd prefix 2001:db8:1::100/32 off-link
leaf01(config-if)# ipv6 nd prefix 2001:db8:1::100/32 no-autoconfig
leaf01(config-if)# ipv6 nd prefix 2001:db8:1::100/32 router-address
leaf01(config-if)# end
leaf01# write memory
leaf01# exit
cumulus@leaf01:mgmt:~$

The vtysh commands write to the /etc/frr/frr.conf file:

cumulus@leaf01:mgmt:~$ sudo cat /etc/frr/frr.conf
...
interface swp1
 ipv6 nd prefix 2001:db8::/32 off-link
 ipv6 nd prefix 2001:db8::/32 router-address
 ipv6 nd prefix 2001:db8::/32 no-autoconfig
 ...

Recursive DNS Servers

To configure recursive DNS servers (RDNSS), you must specify the IPv6 address of each RDNSS you want to advertise.

An optional parameter lets you set the maximum amount of time you want to use the RDNSS for domain name resolution. You can set a value between 0 and 4294967295 seconds or use the keyword infinte to set the time to never expire. If you set the value to 0, Cumulus Linux no longer advertises the RDNSS address.

The following example commands set the RDNSS address to 2001:db8:1::100 and the lifetime to infinite:

cumulus@leaf01:mgmt:~$ nv set interface swp1 ip neighbor-discovery rdnss 2001:db8:1::100 lifetime infinite
cumulus@leaf01:mgmt:~$ nv config apply

cumulus@leaf01:mgmt:~$ sudo vtysh
...
leaf01# configure terminal
leaf01(config)# interface swp1
leaf01(config-if)# ipv6 nd rdnss 2001:db8:1::100 infinite
leaf01(config-if)# end
leaf01# write memory
leaf01# exit
cumulus@leaf01:mgmt:~$

The vtysh commands write to the /etc/frr/frr.conf file:

cumulus@leaf01:mgmt:~$ sudo cat /etc/frr/frr.conf
...
interface swp1
 ipv6 nd rdnss 2001:db8:1::100 infinite
 ...

DNS Search Lists

To configure DNS search lists (DNSSL), you must specify the domain suffix you want to advertise.

An optional parameter lets you set the maximum amount of time you want to use the domain suffix for domain name resolution. You can set a value between 0 and 4294967295 seconds or use the keyword infinte to set the time to never expire. If you set the value to 0, the host does not use the DNSSL.

The following example command sets the domain suffix to accounting.nvidia.com and the maximum amount of time you want to use the domain suffix to infinite:

cumulus@leaf01:mgmt:~$ nv set interface swp1 ip neighbor-discovery dnssl accounting.nvidia.com lifetime infinite
cumulus@leaf01:mgmt:~$ nv config apply

cumulus@leaf01:mgmt:~$ sudo vtysh
...
leaf01# configure terminal
leaf01(config)# interface swp1
leaf01(config-if)# ipv6 nd dnssl accounting.nvidia.com infinite
leaf01(config-if)# end
leaf01# write memory
leaf01# exit
cumulus@leaf01:mgmt:~$

The vtysh commands write to the /etc/frr/frr.conf file:

cumulus@leaf01:mgmt:~$ sudo cat /etc/frr/frr.conf
...
interface swp1
 ipv6 nd dnssl accounting.nvidia.com infinite
...

Home Agents

Mobile IPv6 defines an additional flag in the router advertisement message that indicates if the advertising router is capable of being a Home Agent. Each Home Agent on the home link sets this flag when it sends router advertisements.

You can configure the switch to be a Home Agent with these settings:

  • Set the maximum amount of time you want the router to act as a Home Agent. You can set a value between 0 and 65520 seconds. The default value is 0 (the router is not a Home Agent).
  • Set the Home Agent router preference. You can set a value between 0 and 65535. The default value is 0 (the lowest preference).

The following example commands configure the switch as a Home Agent by setting the maximum amount of time the router acts as a Home Agent to 20000 seconds and the router preference to 100:

cumulus@leaf01:mgmt:~$ nv set interface swp1 ip neighbor-discovery home-agent preference 100
cumulus@leaf01:mgmt:~$ nv set interface swp1 ip neighbor-discovery home-agent lifetime 20000
cumulus@leaf01:mgmt:~$ nv config apply

When you run the above commands, NVUE adds the ipv6 nd home-agent-config-flag line under the interface stanza in the /etc/network/interfaces file in addition to the ipv6 nd home-agent-preference and ipv6 nd home-agent-lifetime lines.

cumulus@leaf01:mgmt:~$ sudo vtysh
...
leaf01# configure terminal
leaf01(config)# interface swp1
leaf01(config-if)# ipv6 nd home-agent-config-flag
leaf01(config-if)# ipv6 nd home-agent-preference 100
leaf01(config-if)# ipv6 nd home-agent-lifetime 0
leaf01(config-if)# end
leaf01# write memory
leaf01# exit
cumulus@leaf01:mgmt:~$

The vtysh commands write to the /etc/frr/frr.conf file:

cumulus@leaf01:mgmt:~$ sudo cat /etc/frr/frr.conf
...
interface swp1
 ipv6 nd home-agent-config-flag
 ipv6 nd home-agent-lifetime 0
 ipv6 nd home-agent-preference 100
...

MTU

You can set the MTU for neighbor discovery messages on an interface. You can configure a value between 1 and 65535.

To following example commands set the MTU on swp1 to 1500:

cumulus@leaf01:mgmt:~$ nv set interface swp1 ip neighbor-discovery mtu 1500
cumulus@leaf01:mgmt:~$ nv config apply

cumulus@leaf01:mgmt:~$ sudo vtysh
...
leaf01# configure terminal
leaf01(config)# interface swp1
leaf01(config-if)# ipv6 nd mtu 1500
leaf01(config-if)# end
leaf01# write memory
leaf01# exit
cumulus@leaf01:mgmt:~$

The vtysh commands write to the /etc/frr/frr.conf file:

cumulus@leaf01:mgmt:~$ sudo cat /etc/frr/frr.conf
...
interface swp1
 ipv6 nd mtu 1500
...

Neighbor Base Reachable Timer

You can set how long a neighbor cache entry is valid with the NVUE nv set system global nd base-reachable-time command. The entry is valid for at least the value between the base reachable time divided by two and three times the base reachable time divided by two. You can specify a value between 30 and 2147483 seconds. The default value is auto; NVUE derives the value for auto from the /etc/sysctl.d/neigh.conf file.

The following example configures the neighbor base reachable timer to 50 seconds.

cumulus@leaf01:~$ nv set system global nd base-reachable-time 50
cumulus@leaf01:~$ nv config apply

To reset the neighbor base reachable timer to the default setting, run the nv unset system global nd base-reachable-time command.

NVIDIA recommends that you run the NVUE command to change the neighbor base reachable timer instead of modifying the /etc/sysctl.d/neigh.conf file manually.

To show the neighbor base reachable timer setting, run the nv show system global nd command:

cumulus@leaf01:~$ nv show system global nd
                              operational  applied  
----------------------------  -----------  ------- 
base-reachable-time           50           50      
garbage-collection-threshold                               
  effective                   17920                        
  maximum                     20480                        
  minimum                     128

Disable ND

To disable ND, run the NVUE nv set interface <interface> ip neighbor-discovery enable off command:

cumulus@leaf01:mgmt:~$ nv set interface swp1 ip neighbor-discovery enable off
cumulus@leaf01:mgmt:~$ nv config apply

Add Static IP Neighbor Table Entries

You can add static IPv6 neighbor table entries for easy management or as a security measure to prevent spoofing and other nefarious activities.

To create a static neighbor entry for an interface with an IPv6 address associated with a MAC address, run the nv set interface <interface> neighbor ipv6 <ip-address> lladdr <mac-address> command.

cumulus@leaf01:mgmt:~$ nv set interface swp51 neighbor ipv6 fe80::4ab0:2dff:fea2:4c79 lladdr 00:00:5E:00:53:51
cumulus@leaf01:mgmt:~$ nv config apply

You can also set a flag to indicate that the neighbour is a router (is-router) or learned externally (ext_learn) and set the neighbor state (delay, failed, incomplete, noarp, permanent, probe, reachable, or stale).

cumulus@leaf01:mgmt:~$ nv set interface swp51 neighbor ipv6 fe80::4ab0:2dff:fea2:4c79 lladdr 00:00:5E:00:53:51 flag is-router
cumulus@leaf01:mgmt:~$ nv set interface swp51 neighbor ipv6 fe80::4ab0:2dff:fea2:4c79 lladdr 00:00:5E:00:53:51 state permanent
cumulus@leaf01:mgmt:~$ nv config apply

To delete an entry in the IP neighbor table, run the nv unset interface <interface> neighbor ipv6 <ip-address> command:

cumulus@leaf01:mgmt:~$ nv unset interface swp51 neighbor ipv6 fe80::4ab0:2dff:fea2:4c79
cumulus@leaf01:mgmt:~$ nv config apply

To create a static neighbor entry for an interface with an IPv6 address associated with a MAC address, add post-up ip neigh add <ipv6-address> lladdr <mac-address> to the interface stanza of the /etc/network/interfaces file, then run the ifreload -a command:

cumulus@leaf01:mgmt:~$ sudo nano /etc/network/interfaces
...
auto swp51
iface swp51
    post-up ip neigh add fe80::4ab0:2dff:fea2:4c79 lladdr 00:00:5E:00:53:51 dev swp51
...

cumulus@leaf01:mgmt:~$ sudo ifreload -a

You can also set a flag to indicate that the IPv6 neighbor is a router (router) or learned externally (extern_learn) and set the neighbor state (delay, failed, incomplete, noarp, permanent, probe, reachable, or stale).

cumulus@leaf01:mgmt:~$ sudo nano /etc/network/interfaces
...
auto swp51
iface swp51
    post-up ip neigh add fe80::4ab0:2dff:fea2:4c79 lladdr 00:00:5E:00:53:51 dev swp51 nud permanent router
...

cumulus@leaf01:mgmt:~$ sudo ifreload -a

To delete a static neighbor entry, remove the post-up ip neigh add line from the interface stanza of the /etc/network/interfaces file.

Show the IP Neighbor Table

To show all the entries in the IP neighbor table, run the nv show interface neighbor command or the Linux ip neighbor command:

cumulus@leaf01:mgmt:~$ nv show interface neighbor
Interface      IP/IPV6                    LLADR(MAC)         State      Flag      
-------------  -------------------------  -----------------  ---------  ----------
eth0           192.168.200.251            48:b0:2d:00:00:01  stale                
               192.168.200.1              48:b0:2d:aa:8b:45  reachable            
               fe80::4ab0:2dff:fe00:1     48:b0:2d:00:00:01  reachable  router    
peerlink.4094  169.254.0.1                48:b0:2d:3f:69:d6  permanent            
               fe80::4ab0:2dff:fe3f:69d6  48:b0:2d:3f:69:d6  reachable  router    
swp51          169.254.0.1                48:b0:2d:a2:4c:79  permanent            
               fe80::4ab0:2dff:fea2:4c79  48:b0:2d:a2:4c:79  reachable  router    
swp52          169.254.0.1                48:b0:2d:48:f1:ae  permanent            
               fe80::4ab0:2dff:fe48:f1ae  48:b0:2d:48:f1:ae  reachable  router    
swp53          169.254.0.1                48:b0:2d:2d:de:93  permanent            
               fe80::4ab0:2dff:fe2d:de93  48:b0:2d:2d:de:93  reachable  router    
swp54          169.254.0.1                48:b0:2d:80:8c:21  permanent            
               fe80::4ab0:2dff:fe80:8c21  48:b0:2d:80:8c:21  reachable  router    
vlan10         10.1.10.3                  44:38:39:22:01:78  permanent            
               10.1.10.101                48:b0:2d:a1:3f:4b  reachable            
               10.1.10.104                48:b0:2d:1d:d7:e8  noarp      |ext_learn
               fe80::4ab0:2dff:fea1:3f4b  48:b0:2d:a1:3f:4b  reachable            
               fe80::4ab0:2dff:fe1d:d7e8  48:b0:2d:1d:d7:e8  noarp      |ext_learn
               fe80::4638:39ff:fe22:178   44:38:39:22:01:78  permanent            
vlan10-v0      10.1.10.101                48:b0:2d:a1:3f:4b  stale                
               fe80::4ab0:2dff:fea1:3f4b  48:b0:2d:a1:3f:4b  stale                
               fe80::4ab0:2dff:fe1d:d7e8  48:b0:2d:1d:d7:e8  stale                
vlan20         10.1.20.105                48:b0:2d:75:bf:9e  noarp      |ext_learn
               10.1.20.102                48:b0:2d:00:e9:05  reachable            
               10.1.20.3                  44:38:39:22:01:78  permanent            
               fe80::4638:39ff:fe22:178   44:38:39:22:01:78  permanent            
               fe80::4ab0:2dff:fe75:bf9e  48:b0:2d:75:bf:9e  noarp      |ext_learn
               fe80::4ab0:2dff:fe00:e905  48:b0:2d:00:e9:05  reachable
...

To show IPv6 entries only, run the Linux ip -6 neighbor command:

cumulus@leaf01:mgmt:~$ ip -6 neighbor
fe80::4ab0:2dff:fe4e:c76a dev vlan30 lladdr 48:b0:2d:4e:c7:6a extern_learn  NOARP proto zebra 
fe80::4ab0:2dff:fea1:3f4b dev vlan10 lladdr 48:b0:2d:a1:3f:4b REACHABLE
fe80::4ab0:2dff:fee9:d399 dev vlan30-v0 lladdr 48:b0:2d:e9:d3:99 STALE
fe80::4ab0:2dff:fe75:bf9e dev vlan20-v0 lladdr 48:b0:2d:75:bf:9e STALE
fe80::4638:39ff:fe22:178 dev vlan20 lladdr 44:38:39:22:01:78 PERMANENT
fe80::4ab0:2dff:fea2:4c79 dev swp51 lladdr 48:b0:2d:a2:4c:79 router REACHABLE
fe80::4ab0:2dff:fe00:1 dev eth0 lladdr 48:b0:2d:00:00:01 router REACHABLE
fe80::4ab0:2dff:fee9:d399 dev vlan30 lladdr 48:b0:2d:e9:d3:99 REACHABLE
fe80::4ab0:2dff:fe48:f1ae dev swp52 lladdr 48:b0:2d:48:f1:ae router REACHABLE
fe80::4ab0:2dff:fe1d:d7e8 dev vlan10 lladdr 48:b0:2d:1d:d7:e8 extern_learn  NOARP proto zebra 
fe80::4ab0:2dff:fea1:3f4b dev vlan10-v0 lladdr 48:b0:2d:a1:3f:4b STALE
fe80::4ab0:2dff:fe80:8c21 dev swp54 lladdr 48:b0:2d:80:8c:21 router REACHABLE
fe80::4ab0:2dff:fe75:bf9e dev vlan20 lladdr 48:b0:2d:75:bf:9e extern_learn  NOARP proto zebra 
fe80::4638:39ff:fe22:178 dev vlan4024_l3 lladdr 44:38:39:22:01:78 PERMANENT
fe80::4ab0:2dff:fe00:e905 dev vlan20-v0 lladdr 48:b0:2d:00:e9:05 STALE
fe80::4ab0:2dff:fe3f:69d6 dev peerlink.4094 lladdr 48:b0:2d:3f:69:d6 router REACHABLE
...

To show all table entries for a specific interface, run the nv show interface <interface_id> neighbor command:

cumulus@leaf01:mgmt:~$ nv show interface swp51 neighbor
ipv4
=========
    IPV4         LLADR(MAC)         State      Flag
    -----------  -----------------  ---------  ----
    10.5.5.51    00:00:5e:00:53:51  permanent      
    169.254.0.1  48:b0:2d:a2:4c:79  permanent
ipv6
=========
    IPV6                       LLADR(MAC)         State      Flag     
    -------------------------  -----------------  ---------  ---------
    fe80::4ab0:2dff:fea2:4c79  48:b0:2d:a2:4c:79  reachable  is-router

To show all IPv6 table entries for an interface, run the nv show interface <interface> neighbor ipv6 command:

cumulus@leaf01:mgmt:~$ nv show interface swp1 neighbor ipv6
IPV6                       LLADR(MAC)         State      Flag
-------------------------  -----------------  ---------  ---------
fe80::1e34:daff:fe6c:dd8   1c:34:da:6c:0d:d8  stale
fe80::3e2c:30ff:fe4b:800   3c:2c:30:4b:08:00  reachable

To show table entries for an interface with a specific IPv6 address, run the nv show interface <interface_id> neighbor ipv6 <ip-address> command:

cumulus@leaf01:mgmt:~$ nv show interface swp51 neighbor ipv6 fe80::4ab0:2dff:fea2:4c79
lladdr
=========
    LLADR(MAC)         State      Flag
    -----------------  ---------  ----
    00:00:5E:00:53:51  permanent

Troubleshooting

To show the ND configuration settings for an interface, run the NVUE nv show interface <interface-id> ip neighbor-discovery command:

cumulus@leaf01:mgmt:~$ nv show interface swp1 ip neighbor-discovery
                      applied             description
--------------------  ------------------  ----------------------------------------------------------------------
enable                on                  Turn the feature 'on' or 'off'.  The default is 'on'.
home-agent
  lifetime            0                   Lifetime of a home agent in seconds
  preference          0                   Home agent's preference value that is used to order the addresses r...
[prefix]              2001:db8:1::100/32  IPv6 prefix configuration
router-advertisement
  enable              on                  Turn the feature 'on' or 'off'.  The default is 'on'.
  fast-retransmit     off                 Allow consecutive RA packets more frequently than every 3 seconds
  hop-limit           100                 Value in hop count field in IP header of the outgoing router advert...
  interval            6000                Maximum time in milliseconds allowed between sending unsolicited mu...
  interval-option     on                  Indicates hosts that the router will use advertisement interval to...
  lifetime            4000                Maximum time in seconds that the router can be treated as default g...
  managed-config      on                  Knob to allow dynamic host to use managed (stateful) protocol for a...
  other-config        off                 Knob to allow dynamic host to use managed (stateful) protocol for a...
  reachable-time      3600000             Time in milliseconds that a IPv6 node is considered reachable
  retransmit-time     4294967295          Time in milliseconds between retransmission of neighbor solicitatio...
  router-preference   high                Hosts use router preference in selection of the default router

To show prefix configuration for an interface, run the nv show interface <interface> ip neighbor-discovery prefix <prefix> command.

cumulus@leaf01:mgmt:~$ nv show interface swp1 ip neighbor-discovery prefix 2001:db8:1::100/32
                    applied     description
------------------  -------     ----------------------------------------------------------------------
autoconfig          on          Indicates to hosts on the local link that the specified prefix can...
off-link            on          Indicates that adverisement makes no statement about on-link or off...
preferred-lifetime  1000000000  Time in seconds that addresses generated from a prefix remain prefe...
router-address      on          Indicates to hosts on the local link that the specified prefix cont...
valid-lifetime      2000000000  Time in seconds the prefix is valid for on-link determination

To show Home Agent configuration for an interface, run the nv show interface <interface> ip neighbor-discovery home-agent command:

cumulus@leaf01:mgmt:~$ nv show interface swp1 ip neighbor-discovery home-agent
            applied  description
----------  -------  ----------------------------------------------------------------------
lifetime    20000    Lifetime of a home agent in seconds
preference  100      Home agent's preference value that is used to order the addresses r...

To show router advertisement configuration for an interface, run the nv show interface <interface> ip neighbor-discovery router-advertisement command. The command also shows the number of router advertisement packets sent on the interface and the number of router advertisement and router solicitation packets received on the interface.

cumulus@leaf01:mgmt:~$ nv show interface swp1 ip neighbor-discovery router-advertisement
                      applied
-----------------     -----------------
enable                on
interval              10000
interval-option       off
fast-retransmit       on
lifetime              1800
reachable-time        0
retransmit-time       0
managed-config        off
other-config          off
hop-limit             64
router-preference     medium
ra-sent               218
ra-received           2
rs-received           1

To show RDNSS configuration for an interface, run the nv show interface <interface> ip neighbor-discovery rdnss <address> command:

cumulus@leaf01:mgmt:~$ nv show interface swp1 ip neighbor-discovery rdnss 2001:db8:1::100
          applied   description
--------  --------  ----------------------------------------------------------------------
lifetime  infinite  Maximum time in seconds for which the server may be used for domain...

To show DNSSL configuration for an interface, run the nv show interface <interface> ip neighbor-discovery dnssl <domain-suffix> command:

cumulus@leaf01:mgmt:~$ nv show interface swp1 ip neighbor-discovery dnssl accounting.nvidia.com
          applied   description
--------  --------  ----------------------------------------------------------------------
lifetime  infinite  Maximum time in seconds for which the domain suffix may be used for...

    Copyright © 2024  NVIDIA Corporation