Open Telemetry Export
Telemetry enables you to collect, send, and analyze large amounts of data, such as traffic statistics, port status, device health and configuration, and events. This data helps you monitor switch performance, health and behavior, traffic patterns, and QoS.
Configure Open Telemetry
Cumulus Linux supports open telemetry (OTEL) export. You can use OTLP to export metrics, such as interface counters, histogram collection, and platform statistic data to an external collector for analysis and visualization.
Cumulus Linux supports open telemetry export on switches with the Spectrum-2 ASIC and later.
To enable open telemetry:
cumulus@switch:~$ nv set system telemetry export otlp state enabled
cumulus@switch:~$ nv config apply
You can enable open telemetry for interface statistics, histogram data, control plane statistics, and platform statistics.
Interface Statistics
When you enable open telemetry for interface statistics, the switch exports counters on all configured interfaces:
cumulus@switch:~$ nv set system telemetry interface-stats export state enabled
cumulus@switch:~$ nv config apply
You can enable additional interface statistic collection per interface for specific ingress buffer traffic classes (0 through 15) and egress buffer priority groups (0 through 7). When you enable these settings, the switch exports interface_pg
and interface_tc
counters for the defined priority groups and traffic classes:
cumulus@switch:~$ nv set system telemetry interface-stats ingress-buffer priority-group 4
cumulus@switch:~$ nv set system telemetry interface-stats egress-buffer traffic-class 12
cumulus@switch:~$ nv config apply
You can enable additional switch priority interface statistic collection on all configured interfaces for specific switch priority values:
cumulus@switch:~$ nv set system telemetry interface-stats switch-priority 4
cumulus@switch:~$ nv config apply
You can adjust the interface statistics sample interval (in seconds). You can specify a value between 1 and 86400. The default value is 1.
cumulus@switch:~$ nv set system telemetry interface-stats sample-interval 100
cumulus@switch:~$ nv config apply
Control Plane Statistics
When you enable open telemetry for control plane statistics, additional counters for control plane packets are exported:
cumulus@switch:~$ nv set system telemetry control-plane-stats export state enabled
cumulus@switch:~$ nv config apply
You can adjust the control plane statistics sample interval (in seconds). You can specify a value between 1 and 86400. The default value is 1.
cumulus@switch:~$ nv set system telemetry control-plane-stats sample-interval 100
cumulus@switch:~$ nv config apply
Histogram Data
When you enable open telemetry for histogram data, your buffer, counter, and latency histogram collection configuration defines the data that the switch exports:
cumulus@switch:~$ nv set system telemetry histogram export state enabled
cumulus@switch:~$ nv config apply
Platform Statistics
When you enable platform statistic open telemetry, data related to CPU, disk, filesystem, memory, and sensor health is exported. To enable all platform statistics globally:
cumulus@switch:~$ nv set system telemetry platform-stats export state enabled
cumulus@switch:~$ nv config apply
If you do not want to enable all platform statistics, you can enable or disable individual platform telemetry components or adjust the sample interval for individual components. The default sample interval is 60 seconds.
cumulus@switch:~$ nv set system telemetry platform-stats class cpu state enabled
cumulus@switch:~$ nv config apply
cumulus@switch:~$ nv set system telemetry platform-stats class cpu sample-interval 100
cumulus@switch:~$ nv config apply
cumulus@switch:~$ nv set system telemetry platform-stats class disk state enabled
cumulus@switch:~$ nv config apply
cumulus@switch:~$ nv set system telemetry platform-stats class disk sample-interval 100
cumulus@switch:~$ nv config apply
cumulus@switch:~$ nv set system telemetry platform-stats class file-system state enabled
cumulus@switch:~$ nv config apply
cumulus@switch:~$ nv set system telemetry platform-stats class file-system sample-interval 100
cumulus@switch:~$ nv config apply
cumulus@switch:~$ nv set system telemetry platform-stats class memory state enabled
cumulus@switch:~$ nv config apply
cumulus@switch:~$ nv set system telemetry platform-stats class memory sample-interval 100
cumulus@switch:~$ nv config apply
cumulus@switch:~$ nv set system telemetry platform-stats class environment-sensors state enabled
cumulus@switch:~$ nv config apply
cumulus@switch:~$ nv set system telemetry platform-stats class environment-sensors sample-interval 100
cumulus@switch:~$ nv config apply
gRPC OTLP Export
To configure the open telemetry export destination:
-
Configure gRPC to communicate with the collector by providing the collector destination IP address or hostname. Specify the port to use for communication if it is different from the default port 8443:
cumulus@switch:~$ nv set system telemetry export otlp grpc destination 10.1.1.100 port 4317 cumulus@switch:~$ nv config apply
-
Configure an X.509 certificate to secure the gRPC connection:
cumulus@switch:~$ nv set system telemetry export otlp grpc cert-id <certificate> cumulus@switch:~$ nv config apply
By default, OTLP export is in secure mode that requires a certificate. For connections without a configured certificate, you must enable insecure
mode with the nv set system telemetry export otlp grpc insecure enabled
command.
Show Telemetry Export Configuration
To show the telemetry export configuration, run the nv show system telemetry export
command:
cumulus@switch:~$ nv show system telemetry export
applied pending
------------------ -------- --------
vrf default default
otlp
state disabled disabled
grpc
insecure disabled disabled
port 8443 8443
[destination]
To show the OTLP gRPC destination configuration, run the nv show system telemetry export otlp grpc destination
command.
Static Labels
You can apply static labels to switches and individual interfaces to configure descriptions for devices and interface roles. Exported OTLP data includes these label names and descriptions.
- Cumulus Linux supports up to 10 device labels and up to 10 interface labels.
- Label name and description strings can include alphanumeric characters with underscores, periods, or dashes. If spaces are included in the string, wrap the entire string inside double or single quotes.
To configure a switch device label Data_Center_Location
and a string identifying it as part of Data_Center_B
:
cumulus@switch:~$ nv set system telemetry label "Data Center Location" description "Data Center B"
cumulus@switch:~$ nv config apply
Validate device label configuration with the nv show system telemetry label
command:
cumulus@switch:~$ nv show system telemetry label
description
-------------------- -------------
Data Center Location Data Center B
To configure a switch interface label interface_swp10_label
with the description Server 10 connection
:
cumulus@switch:~$ nv set interface swp10 telemetry label "interface_swp10_label" description "Server 10 connection"
cumulus@switch:~$ nv config apply
Validate the configuration with the nv show system telemetry label
command:
cumulus@switch:~$ nv show system telemetry label
description
-------------------- -------------
Data Center Location Data Center B
Validate interface label configuration with the nv show interface <interface> telemetry label
command:
cumulus@switch:~$ nv show interface swp10 telemetry label
description
--------------------- --------------------
interface_swp10_label Server 10 connection
Telemetry Data Format
Cumulus Linux exports statistics and histogram data in the formats defined in this section.
Interface Statistic Format
The interface statistic data samples that the switch exports to the OTEL collector are gauge streams that include the interface name as an attribute and the statistics value reported in the asDouble exemplar.
Name | Description |
---|---|
nvswitch_interface_oper_state |
Interface operational state as a bitmap: (None[0], Up[1], Down[2], Invalid[4], Error[8]) |
nvswitch_interface_dot3_control_in_unknown_opcodes |
Input 802.3 unknown opcode counter. |
nvswitch_interface_dot3_in_pause_frames |
Input 802.3 pause frame counter. |
nvswitch_interface_dot3_out_pause_frames |
Output 802.3 pause frame counter. |
nvswitch_interface_dot3_stats_alignment_errors |
802.3 alignment error counter. |
nvswitch_interface_dot3_stats_carrier_sense_errors |
802.3 interface carrier sense error counter. |
nvswitch_interface_dot3_stats_deferred_transmissions |
802.3 deferred transmission counter. |
nvswitch_interface_dot3_stats_excessive_collisions |
802.3 excessive collisions counter. |
nvswitch_interface_dot3_stats_fcs_errors |
802.3 FCS error counter. |
nvswitch_interface_dot3_stats_frame_too_longs |
802.3 excessive frame size counter. |
nvswitch_interface_dot3_stats_internal_mac_receive_errors |
802.3 internal MAC receive error counter. |
nvswitch_interface_dot3_stats_internal_mac_transmit_errors |
802.3 internal MAC transmit error counter. |
nvswitch_interface_dot3_stats_late_collisions |
802.3 late collisions counter. |
nvswitch_interface_dot3_stats_multiple_collision_frames |
802.3 multiple collision frames counter. |
nvswitch_interface_dot3_stats_single_collision_frames |
802.3 single collision frames counter. |
nvswitch_interface_dot3_stats_sqe_test_errors |
802.3 SQE test error counter. |
nvswitch_interface_dot3_stats_symbol_errors |
802.3 symbol error counter. |
nvswitch_interface_performance_marked_packets |
Interface performance marked packets, with marking as ece or ecn . |
nvswitch_interface_discards_ingress_general |
Interface ingress general discards counter. |
nvswitch_interface_discards_ingress_policy_engine |
Interface ingress policy engine discards counter. |
nvswitch_interface_discards_ingress_vlan_membership |
Interface ingress VLAN membership filter discards counter. |
nvswitch_interface_discards_ingress_tag_frame_type |
Interface ingress VLAN tag filter discards counter. |
nvswitch_interface_discards_egress_vlan_membership |
Interface egress VLAN emmbership filter discards counter. |
nvswitch_interface_discards_loopback_filter |
Interface loopback filter discards counter. |
nvswitch_interface_discards_egress_general |
Interface egress general discards counter. |
nvswitch_interface_discards_egress_link_down |
Interface egress link down discards counter. |
nvswitch_interface_discards_egress_hoq |
Interface egress head-of-queue timeout discards. |
nvswitch_interface_discards_port_isolation |
Interface port isolation filter discards. |
nvswitch_interface_discards_egress_policy_engine |
Interface egress policy engine discards. |
nvswitch_interface_discards_ingress_tx_link_down |
Interface ingress transmit link down discards. |
nvswitch_interface_discards_egress_stp_filter |
Interface egress spanning tree filter discards. |
nvswitch_interface_discards_egress_hoq_stall |
Interface egress head-of-queue stall discards. |
nvswitch_interface_discards_egress_sll |
Interface egress switch lifetime limit discards. |
nvswitch_interface_discards_ingress_discard_all |
Interface total ingress discards. |
nvswitch_interface_tx_stats_pkts64octets |
Total packets transmitted, 64 octets in length. |
nvswitch_interface_tx_stats_pkts65-to127octets |
Total packets transmitted, 64 octets in length. |
nvswitch_interface_tx_stats_pkts256-to511octets |
Total packets transmitted, 256-511 octets in length. |
nvswitch_interface_tx_stats_pkts512-to1023octets |
Total packets transmitted, 512-1023 octets in length. |
nvswitch_interface_tx_stats_pkts1024-to1518octets |
Total packets transmitted, 1024-1518 octets in length. |
nvswitch_interface_tx_stats_pkts1519-to2047octets |
Total packets transmitted, 1519-2047 octets in length. |
nvswitch_interface_tx_stats_pkts2048-to4095octets |
Total packets transmitted, 2048-4095 octets in length. |
nvswitch_interface_tx_stats_pkts4096-to8191octets |
Total packets transmitted, 4096-8191 octets in length. |
nvswitch_interface_tx_stats_pkts8192-to10239octets |
Total packets transmitted, 8192-10239 octets in length. |
nvswitch_interface_ether_stats_pkts64octets |
Total packets received, 64 octets in length. |
nvswitch_interface_ether_stats_pkts65to127octets |
Total packets received, 65-127 octets in length. |
nvswitch_interface_ether_stats_pkts128to255octets |
Total packets received, 128-255 octets in length. |
nvswitch_interface_ether_stats_pkts256to511octets |
Total packets received, 256-511 octets in length. |
nvswitch_interface_ether_stats_pkts512to1023octets |
Total packets received, 512-1023 octets in length. |
nvswitch_interface_ether_stats_pkts1024to1518octets |
Total packets received, 1024-1518 octets in length. |
nvswitch_interface_ether_stats_pkts1519to2047octets |
Total packets received, 1519-2047 octets in length. |
nvswitch_interface_ether_stats_pkts2048to4095octets |
Total packets received, 2048-4095 octets in length. |
nvswitch_interface_ether_stats_pkts4096to8191octets |
Total packets received, 4096-8191 octets in length. |
nvswitch_interface_ether_stats_pkts8192to10239octets |
Total packets received, 8192-10239 octets in length. |
nvswitch_interface_carrier_up_changes_total |
Total number of carrier up transitions for the interface. |
nvswitch_interface_carrier_last_change_time_ms |
Time of last carrier change for the interface as Unix epoch timestamp, with millisecond granularity. |
nvswitch_interface_carrier_down_changes_total |
Total number of carrier down transitions for the interface. |
nvswitch_interface_carrier_changes_total |
Total number of carrier changes for the interface. |
nvswitch_interface_mtu_bytes |
Operational MTU for the interface in bytes. |
nvswitch_interface_info |
Provides information about the interface: MAC address, duplex, ifalias, interface name, operstate. |
nvswitch_interface_iface_id |
The ifindex for the interface. |
nvswitch_interface_flags |
Kernel device flags set for an interface as an integer representing the kernel net_device flags bitmask. |
nvswitch_interface_proto_down |
Interface protocol down status. |
The following additional interface traffic class statistics are collected and exported when you configure the nv set system telemetry interface-stats egress-buffer traffic-class <class>
command:
Name | Description |
---|---|
nvswitch_interface_tc_tx_bc_frames |
Interface egress traffic class transmit broadcast frames counter. |
nvswitch_interface_tc_tx_ecn_marked_tc |
Interface egress traffic class transmit ECN marked counter. |
nvswitch_interface_tc_tx_frames |
Interface egress traffic class trasmit frames counter. |
nvswitch_interface_tc_tx_mc_frames |
Interface egress traffic class trasmit multicast frames counter. |
nvswitch_interface_tc_tx_no_buffer_discard_uc |
Interface egress traffic class transmit unicast no buffer discard counter. |
nvswitch_interface_tc_tx_octet |
Interface egress traffic class transmit bytes counter. |
nvswitch_interface_tc_tx_queue |
Interface egress traffic class transmit queue counter. |
nvswitch_interface_tc_tx_uc_frames |
Interface egress traffic class transmit unicast frames counter. |
nvswitch_interface_tc_tx_wred_discard |
Interface egress traffic class transmit WRED discard counter. |
The following additional interface priority group statistics are collected and exported when you configure the nv set system telemetry interface-stats ingress-buffer priority-group <priority>
command:
Name | Description |
---|---|
nvswitch_interface_pg_rx_buffer_discard |
Interace ingress priority group receive buffer discard counter. |
nvswitch_interface_pg_rx_frames |
Interface ingress priority group receive frames counter. |
nvswitch_interface_pg_rx_octets |
Interface ingress priority group receive bytes counter. |
nvswitch_interface_pg_rx_shared_buffer_discard |
Interface ingress priority group receive shared buffer discard counter. |
nvswitch_interface_pg_rx_uc_frames |
Interface receive priority group unicast frames counter. |
nvswitch_interface_pg_rx_mc_frames |
Interface receive priority group multicast frames counter. |
nvswitch_interface_pg_rx_bc_frames |
Interface receive priority group broadcast frames counter. |
nvswitch_interface_pg_tx_octets |
Interface receive priority group transmit bytes counter. |
nvswitch_interface_pg_tx_uc_frames |
Interface receive priority group transmit unicast frames counter. |
nvswitch_interface_pg_tx_mc_frames |
Interface receive priority group transmit multicast frames counter. |
nvswitch_interface_pg_tx_bc_frames |
Interface receive priority group transmit broadcast frames counter. |
nvswitch_interface_pg_tx_frames |
Interface receive priority group transmit frames counter. |
nvswitch_interface_pg_rx_pause |
Interface receive priority group receive pause counter. |
nvswitch_interface_pg_rx_pause_duration |
Interface receive priority group receive pause duration counter. |
nvswitch_interface_pg_tx_pause |
Interface receive priority group transmit pause counter. |
nvswitch_interface_pg_tx_pause_duration |
Interface receive priority group transmit pause duration counter. |
nvswitch_interface_pg_rx_pause_transition |
Interface receive priority group receive pause transition counter. |
nvswitch_interface_pg_rx_discard |
Interface receive priority group receive discard counter. |
The following additional interface switch priority statistics are collected and exported when you configure the nv set system telemetry interfaces-stats switch-priority <priority>
command:
Name | Description |
---|---|
nvswitch_interface_sp_rx_bc_frames |
Received broadcast counter for the switch priority |
nvswitch_interface_sp_rx_discard |
Receive discard counter for the switch priority |
nvswitch_interface_sp_rx_frames |
Receive frame counter for the switch priority. |
nvswitch_interface_sp_rx_mc_frames |
Receive multicast frame counter for the switch priority. |
nvswitch_interface_sp_rx_octets |
Receive octets counter for the switch priority. |
nvswitch_interface_sp_rx_pause |
Receive pause counter for the switch priority. |
nvswitch_interface_sp_rx_pause_duration |
Recieve pause duration counter for the switch priority. |
nvswitch_interface_sp_rx_pause_transition |
Recieve pause transition counter for the switch priority. |
nvswitch_interface_sp_rx_uc_frames |
Receive unicast frame counter for the switch priority. |
nvswitch_interface_sp_tx_bc_frames |
Transmit broadcast frame counter for the switch priority. |
nvswitch_interface_sp_tx_frames |
Transmit frame counter for the switch priority. |
nvswitch_interface_sp_tx_mc_frames |
Transmit multicast frame counter for the switch priority. |
nvswitch_interface_sp_tx_octets |
Transmit octets counter for the switch priority. |
nvswitch_interface_sp_tx_pause |
Transmit pause counter for the switch priority. |
nvswitch_interface_sp_tx_pause_duration |
Transmit pause duration for the switch priority. |
nvswitch_interface_sp_tx_uc_frames |
Transmit unicast frame counter for the switch priority. |
Control Plane Statistic Format
When you enable control plane statistic telemetry, the following statistics are exported:
Name | Description |
---|---|
nvswitch_control_plane_tx_packets |
Control plane transmit packets. |
nvswitch_control_plane_tx_bytes |
Control plane transmit bytes. |
nvswitch_control_plane_rx_packets |
Control plane receive packets. |
nvswitch_control_plane_rx_bytes |
Control plane receive bytes. |
nvswitch_control_plane_rx_buffer_drops |
Control plane receive buffer drops. |
nvswitch_control_plane_trap_rx_packets |
Control plane trap group receive packets. |
nvswitch_control_plane_trap_rx_event_count |
Control plane trap group receive events. |
nvswitch_control_plane_trap_rx_drop |
Control plane trap group receive drops. |
nvswitch_control_plane_trap_rx_bytes |
Control plane trap group receive bytes. |
nvswitch_control_plane_trap_group_rx_packets |
Control plane trap group receive packets. |
nvswitch_control_plane_trap_group_rx_bytes |
Control plane trap group receive bytes. |
nvswitch_control_plane_trap_group_pkt_violations |
Control plane trap group packet violations. |
Platform Statistic Format
When you enable platform statistic telemetry globally, or when you enable telemetry for the individual components, the following statistics are exported:
CPU statistics include the CPU core number and operation mode (user, system, idle, iowait, irq, softirq, steal, guest, guest_nice).
Name | Description |
---|---|
node_cpu_core_throttles_total |
Number of times a CPU core has been throttled. |
node_cpu_frequency_max_hertz |
Maxiumum CPU thread frequency in hertz. |
node_cpu_frequency_min_hertz |
Minimum CPU thread frequency in hertz. |
node_cpu_guest_seconds_total |
Seconds the CPUs spent in guests for each mode. |
node_cpu_package_throttles_total |
Number of times the CPU package has been throttled. |
node_cpu_scaling_frequency_hertz |
Current scaled CPU thread frequency in hertz. |
node_cpu_scaling_frequency_max_hertz |
Maximum scaled CPU thread frequency in hertz. |
node_cpu_scaling_frequency_min_hertz |
Minimum scaled CPU thread frequency in hertz. |
node_cpu_seconds_total |
Seconds the CPU spent in each mode. |
Name | Description |
---|---|
node_disk_ata_rotation_rate_rpm |
ATA disk rotate rate in RPMs. (0 for SSDs). |
node_disk_ata_write_cache |
ATA disk write cache presence. |
node_disk_ata_write_cache_enabled |
ATA disk write cache status (enabled or disabled). |
node_disk_discard_time_seconds_total |
Total number of seconds spent by all discards. |
node_disk_discarded_sectors_total |
Total number of sectors discarded successfully. |
node_disk_discards_completed_total |
Total number of discards discards completed. |
node_disk_discards_merged_total |
Total number of discards merged. |
node_disk_flush_requests_time_seconds_total |
Total number of seconds spent by all flush requests. |
node_disk_flush_requests_total |
The total number of flush requests completed successfully. |
node_disk_info |
Disk information from /sys/block/<block_device> . |
node_disk_io_now |
Number of I/Os in progress. |
node_disk_io_time_seconds_total |
Total seconds spent during I/O. |
node_disk_io_time_weighted_seconds_total |
Weighted number of seconds spent during I/O. |
node_disk_read_bytes_total |
Total number of bytes read successfully. |
node_disk_read_time_seconds_total |
Total number of seconds spent by all reads. |
node_disk_reads_completed_total |
Total number of reads completed successfully. |
node_disk_reads_merged_total |
Total number of reads merged. |
node_disk_write_time_seconds_total |
Total number of seconds spent by all writes. |
node_disk_writes_completed_total |
Total number of writes completed successfully. |
node_disk_writes_merged_total |
Number of writes merged. |
node_disk_written_bytes_total |
Total number of bytes written successfully. |
Name | Description |
---|---|
node_filesystem_avail_bytes |
Filesystem space available to non-root users in bytes. |
node_filesystem_device_error |
Whether an error occurred while getting statistics for the given device. |
node_filesystem_files |
Filesystem total file nodes. |
node_filesystem_files_free |
Filesystem total free file nodes. |
node_filesystem_free_bytes |
Filesystem free space in bytes. |
node_filesystem_readonly |
Filesystem read-only status. |
node_filesystem_size_bytes |
Filesystem size in bytes. |
Name | Description |
---|---|
node_memory_Active_anon_bytes |
/proc/meminfo Active_anon bytes. |
node_memory_Active_bytes |
/proc/meminfo Active bytes. |
node_memory_Active_file_bytes |
/proc/meminfo Active_file bytes. |
node_memory_AnonHugePages_bytes |
/proc/meminfo AnonHugePages bytes. |
node_memory_AnonPages_bytes |
/proc/meminfo AnonPages bytes. |
node_memory_Bounce_bytes |
/proc/meminfo Bounce bytes. |
node_memory_Buffers_bytes /proc/meminfo Buffers bytes. |
|
node_memory_Cached_bytes |
/proc/meminfo Cached bytes. |
node_memory_CommitLimit_bytes |
/proc/meminfo CommitLimit bytes. |
node_memory_Committed_AS_bytes |
/proc/meminfo Committed_AS bytes. |
node_memory_DirectMap1G_bytes |
/proc/meminfo DirectMap1G bytes. |
node_memory_DirectMap2M_bytes |
/proc/meminfo DirectMap2M bytes. |
node_memory_DirectMap4k_bytes |
/proc/meminfo DirectMap4k bytes. |
node_memory_Dirty_bytes |
/proc/meminfo Dirty bytes. |
node_memory_FileHugePages_bytes |
/proc/meminfo FileHugePages bytes. |
node_memory_FilePmdMapped_bytes |
/proc/meminfo FilePmdMapped bytes. |
node_memory_HardwareCorrupted_bytes |
/proc/meminfo HardwareCorrupted bytes. |
node_memory_HugePages_Free |
/proc/meminfo HugePages_Free. |
node_memory_HugePages_Rsvd |
/proc/meminfo HugePages_Rsvd. |
node_memory_HugePages_Surp |
/proc/meminfo HugePages_Surp. |
node_memory_HugePages_Total |
/proc/meminfo HugePages_Total. |
node_memory_Hugepagesize_bytes |
/proc/meminfo Hugepagesize bytes. |
node_memory_Hugetlb_bytes |
/proc/meminfo Hugetlb bytes. |
node_memory_Inactive_anon_bytes |
/proc/meminfo Inactive_anon bytes. |
node_memory_Inactive_bytes |
/proc/meminfo Inactive bytes. |
node_memory_Inactive_file_bytes |
/proc/meminfo Inactive_file bytes. |
node_memory_KReclaimable_bytes |
/proc/meminfo KReclaimable bytes. |
node_memory_KernelStack_bytes |
/proc/meminfo KernelStack bytes. |
node_memory_Mapped_bytes |
/proc/meminfo Mapped bytes. |
node_memory_MemAvailable_bytes |
/proc/meminfo MemAvailable bytes. |
node_memory_MemFree_bytes |
/proc/meminfo MemFree bytes. |
node_memory_MemTotal_bytes |
/proc/meminfo MemTotal bytes. |
node_memory_Mlocked_bytes |
/proc/meminfo Mlocked bytes. |
node_memory_NFS_Unstable_bytes |
/proc/meminfo NFS_Unstable bytes. |
node_memory_PageTables_bytes |
/proc/meminfo PageTables bytes. |
node_memory_Percpu_bytes |
/proc/meminfo Percpu bytes. |
node_memory_SReclaimable_bytes |
/proc/meminfo SReclaimable bytes. |
node_memory_SUnreclaim_bytes |
/proc/meminfo SUnreclaim bytes. |
node_memory_SecPageTables_bytes |
/proc/meminfo SecPageTables bytes. |
node_memory_ShmemHugePages_bytes |
/proc/meminfo ShmemHugePages bytes. |
node_memory_ShmemPmdMapped_bytes |
/proc/meminfo ShmemPmdMapped bytes. |
node_memory_Shmem_bytes |
/proc/meminfo Shmem bytes. |
node_memory_Slab_bytes |
/proc/meminfo Slab bytes. |
node_memory_SwapCached_bytes |
/proc/meminfo SwapCached bytes. |
node_memory_SwapFree_bytes |
/proc/meminfo SwapFree bytes. |
node_memory_SwapTotal_bytes |
/proc/meminfo SwapTotal bytes. |
node_memory_Unevictable_bytes |
/proc/meminfo Unevictable bytes. |
node_memory_VmallocChunk_bytes |
/proc/meminfo VmallocChunk bytes. |
node_memory_VmallocTotal_bytes |
/proc/meminfo VmallocTotal bytes. |
node_memory_VmallocUsed_bytes |
/proc/meminfo VmallocUsed bytes. |
node_memory_WritebackTmp_bytes |
/proc/meminfo WritebackTmp bytes. |
node_memory_Writeback_bytes |
/proc/meminfo Writeback bytes. |
node_memory_Zswap_bytes |
/proc/meminfo Zswap bytes. |
node_memory_Zswapped_bytes |
/proc/meminfo Zswapped bytes. |
Name | Description |
---|---|
nvswitch_env_fan_cur_speed |
Current fan speed in RPM. |
nvswitch_env_fan_dir |
Fan direction (0: Front2Back, 1: Back2Front). |
nvswitch_env_fan_max_speed |
Fan maximum speed in RPM. |
nvswitch_env_fan_min_speed |
Fan minimum speed in RPM. |
nvswitch_env_fan_state |
Fan status (0: ABSENT, 1: OK, 2: FAILED, 3: BAD). |
nvswitch_env_psu_capacity |
PSU capacity in watts. |
nvswitch_env_psu_current |
PSU current in amperes. |
nvswitch_env_psu_power |
PSU power in watts. |
nvswitch_env_psu_state |
PSU state (0: ABSENT, 1: OK, 2: FAILED, 3: BAD). |
nvswitch_env_psu_voltage |
PSU voltage in volts. |
nvswitch_env_temp_crit |
Critical temperature threshold in centigrade. |
nvswitch_env_temp_current |
Current temperature in centigrade. |
nvswitch_env_temp_max |
Maximum temperature threshold in centigrade. |
nvswitch_env_temp_min |
Minimum temperature threshold in centigrade. |
nvswitch_env_temp_state |
Temperature sensor status (0: ABSENT, 1: OK, 2: FAILED, 3: BAD). |
Histogram Data Format
The histogram data samples that the switch exports to the OTEL collector are histogram data points that include the histogram bucket (bin) counts and the respective queue length size boundaries for each bucket. Latency and counter histogram data are also exported, if configured.
Latency histogram bucket counts do not increment in exported telemetry data if there are no packets transmitted in the traffic class during the sample interval.
The switch sends a sample with the following names for each interface enabled for ingress and egress buffer, latency, and/or counter histogram collection:
Name | Description |
---|---|
nvswitch_histogram_interface_egress_buffer |
Histogram interface egress buffer queue depth. |
nvswitch_histogram_interface_ingress_buffer |
Histogram interface ingress buffer queue depth. |
nvswitch_histogram_interface_counter |
Histogram interface counter data. |
nvswitch_histogram_interface_latency |
Histogram interface latency data. |
Static Label Format
Device static labels are exported in the resource metric section of OTLP data:
Interface static labels are exported as attributes in the gauge metrics for each interface.