VirtualBox

This section describes how to install and set up Cumulus VX in VirtualBox to create the two leaf and one spine topology shown below.

In the topology, leaf01 and leaf02 are the access layer switches on the network. leaf01 and leaf02 connect to spine01, which is the aggregation layer switch on the network. To facilitate additional configuration after the initial setup descibed in this guide, leaf01 and leaf02 also have two connections to each other.

Follow the steps below to:

• Create three VMs (leaf01, leaf02, and spine01) and the network connections between them
• Log in to the switches
• Perform basic switch configuration
• Verify configuration

These steps were tested with Cumulus VX 4.2 and VirtualBox version 6.1.12 on macOS version 10.14.6.

Create and Configure the VMs

The following procedure creates leaf01, leaf02, and spine01 and the network connections between them. This section assumes you have VirtualBox experience.

Download and Install the Software

1. Download and install VirtualBox.
2. Download the OVA VirtualBox image.

Create the VMs

Follow these steps for each VM (leaf01, leaf02, and spine01)

1. Open the VirtualBox application and select Import Appliance from the File menu.
2. Browse for the OVA disk image you downloaded, click the Open button, then click Continue.
3. In the Appliance settings, change the name of the VM to leaf01, then click Import to begin the import process.

   

4. In the VirtualBox Manager window, right click the leaf01 VM, then select Clone.
5. Change the name of the VM to leaf02, then click Continue.
6. Make sure Full Clone is selected, then click Clone.
7. Repeat steps 4 through 6 to create spine01.

Create Network Connections

VirtualBox network adapters start with eth0, then swp1, swp2 and swp3. Settings for Adapter 1 apply to eth0, settings for Adapter 2 apply to swp1, and so on.

Configure the network adapter settings for leaf01, leaf02, and spine01 to create point-to-point connections, as shown below.

Follow these steps for each VM (leaf01, leaf02, and spine01):

1. In the VirtualBox Manager window, select the VM.

2. Click Settings, then click Network.

3. Configure the Adapters on each VM as shown below, then click OK to save the network connections.

   • Make sure to select the Paravirtualized Network (virtio-net) network Adapter Type for all adapters
   • Enable Promiscuous Mode for all adapters (except Adapter 1) to allow for LACP bonding to operate properly.
   • Do not change the MAC Addresses, which get configured automatically.

   leaf01 configuration

   Adapter 1

   

   Adapter 2

   

   Adapter 3

   

   Adapter 4

   

   leaf02 configuration

   Adapter 1

   

   Adapter 2

   

   Adapter 3

   

   Adapter 4

   

   spine01 configuration

   Adapter 1

   

   Adapter 2

   

   Adapter 3

   

4. Power on the VMs.

Log in to the Switches

Log in to each switch with the cumulus account and default password cumulus. When you log in for the first time, you are prompted to change the default password.

If you are using Cumulus VX 4.1.1 or earlier, the default password is CumulusLinux!. You are not prompted to change the default password.

For more information on the required password change, see the Cumulus Linux documentation.

Basic Switch Configuration

Run these commands on each switch to change the hostname and bring up the interfaces. Exit the switch, then log back in to see the new hostname at the prompt.

cumulus@cumulus:mgmt:~$ net add hostname leaf01
cumulus@cumulus:mgmt:~$ net add interface swp1,swp2,swp3
cumulus@cumulus:mgmt:~$ net commit
cumulus@cumulus:mgmt:~$ exit

cumulus@cumulus:mgmt:~$ net add hostname leaf02
cumulus@cumulus:mgmt:~$ net add interface swp1,swp2,swp3
cumulus@cumulus:mgmt:~$ net commit
cumulus@cumulus:mgmt:~$ exit

cumulus@cumulus:mgmt:~$ net add hostname spine01
cumulus@cumulus:mgmt:~$ net add interface swp1,swp2
cumulus@cumulus:mgmt:~$ net commit
cumulus@cumulus:mgmt:~$ exit

Verify Configuration

Run the following commands on each switch to verify the configuration:

cumulus@leaf01:mgmt:~$ net show lldp
LocalPort    Speed    Mode          RemoteHost     RemotePort
-----------  -------  ------------  ------------   ------------
swp1         1G       Default       spine01        swp1
swp2         1G       Default       leaf02         swp2
swp3         1G       Default       leaf02         swp3

cumulus@leaf02:mgmt:~$ net show lldp
LocalPort    Speed    Mode          RemoteHost     RemotePort
-----------  -------  ------------  ------------   ------------
swp1         1G       Default       spine01        swp2
swp2         1G       Default       leaf01         swp2
swp3         1G       Default       leaf01         swp3

cumulus@spine01:mgmt:~$ net show lldp
LocalPort    Speed    Mode          RemoteHost     RemotePort
-----------  -------  ------------  ------------   ------------
swp1         1G       Default       leaf01         swp1
swp2         1G       Default       leaf02         swp1

Run the following commands on each switch to show system information:

cumulus@leaf01:mgmt:~$ net show system
Hostname..............leaf01
Build.................Cumulus Linux 4.2.0
Uptime................0.00.23.740000
Model.................Cumulus VX
Memory................768MB
Disk..................6GB
Vendor Name...........Cumulus Networks
Part Number...........4.2.0
Base MAC Address......4:00:27:39:B1:12
Serial Number.........4:00:27:39:B1:12
Product Name..........VX

Next Steps

• Try out advanced configurations. You can update your virtual environment to be able to use the Cumulus Linux on-demand self-paced labs (a quick and easy way to learn the fundamentals). You can also run the topology converter to simulate a custom network topology with VirtualBox and Vagrant, or KVM-QEMU and Vagrant.
• Try NVIDIA Air, which is a free, personal, virtual data center network that provides a low-effort way to see Cumulus Networks technology in action. This is a good way to try out Cumulus Linux if you have platform or disk limitations.