check

Three sets of validation commands are available, all for verifying the health and performance of network protocols and services:

netq check commands. These commands check whether your network’s devices, hosts, network protocols, and services are operating as expected. They ‘validate’ your network against an ideal setup and report mismatches and recommendations. They allow filtering by hostname, can include or exclude selected tests, and some have additional options.
netq add validation commands. Use these commands to validate various elements in your network fabric. The results appear in the Validation Result cards in the UI, where you can filter them.
Validation management commands. netq show validation settings displays a list of all jobs and job settings and netq del validation allows you to remove validations.

Refer to the Validation Tests Reference for a description of the tests run as part of each validation.

netq check addresses

Searches for duplicate IPv4 and IPv6 addresses assigned to interfaces across devices in the inventory, and checks for duplicate /32 host routes in each VRF.

Syntax

netq check addresses 
    [label <text-label-name> | hostnames <text-list-hostnames>] 
    [check_filter_id <text-check-filter-id>] 
    [include <addr-number-range-list> | exclude <addr-number-range-list>]
    [around <text-time>] 
    [json | summary]

Required Arguments

None

Options

Option	Value	Description
label	<text-label-name>	Reserved
hostnames	<text-list-hostnames>	Comma-separated list (no spaces) of hostnames to include in validation
check_filter_id	<text-check-filter-id>	Include the specific filter for a validation
include	<agent-number-range-list>	Include the specified validation tests
exclude	<agent-number-range-list>	Exclude the specified validation tests
around	<text-time>	Indicates how far to go back in time for the network state information. Write the value using text (versus a UTP representation for example). Note there is no space between the number and unit of time. Valid values include: <1-xx>s: number of seconds <1-xx>m: number of minutes <1-xx>h: number of hours <1-xx>d: number of days
json	NA	Display the output in JSON format
summary	NA	Display only the summary information and test results. Do not display details for tests that failed or had warnings.

Sample Usage

cumulus@switch:mgmt:~$ netq check addresses
addr check result summary:

Total nodes         : 25
Checked nodes       : 25
Failed nodes        : 0
Rotten nodes        : 0
Warning nodes       : 0
Skipped Nodes       : 0


IPV4 Duplicate Address Test   : passed
IPV6 Duplicate Address Test   : passed

netq show address-history
netq add validation

netq check agents

Validates the communication status of all nodes (leafs, spines, and hosts) running the NetQ Agent in your network fabric. The output displays the status (passed/failed/skipped) of all tests and a summary including:

Total number of nodes found
Number of nodes validated
Number of nodes that failed the validation
Number of nodes that have been silent for 120 seconds (rotten)
Number of nodes with warnings

Syntax

netq check agents
    [hostnames <text-list-hostnames>]
    [check_filter_id <text-check-filter-id>]
    [include <agents-number-range-list> | exclude <agents-number-range-list>]
    [around <text-time>]
    [json | summary]

Required Arguments

None

Options

Option	Value	Description
hostnames	<text-list-hostnames>	Comma-separated list (no spaces) of hostnames to include in validation
check_filter_id	<text-check-filter-id>	Include the specific filter for a validation
include	<agent-number-range-list>	Include the specified validation tests
exclude	<agent-number-range-list>	Exclude the specified validation tests
around	<text-time>	Indicates how far to go back in time for the network state information. Write the value using text (versus a UTP representation for example). Note there is no space between the number and unit of time. Valid values include: <1-xx>s: number of seconds <1-xx>m: number of minutes <1-xx>h: number of hours <1-xx>d: number of days
json	NA	Display the output in JSON format
summary	NA	Display only the summary information and test results. Do not display details for tests that failed or had warnings.

Sample Usage

Basic validation that runs all tests on all devices:

cumulus@switch:~$ netq check agents
agent check result summary:

Total nodes         : 21
Checked nodes       : 21
Failed nodes        : 0
Rotten nodes        : 0
Warning nodes       : 0

Agent Health Test   : passed

Validation for selected devices:

cumulus@switch:~$ netq check agents hostnames leaf01,leaf02,leaf03,leaf04
agent check result summary:

Total nodes         : 4
Checked nodes       : 4
Failed nodes        : 0
Rotten nodes        : 0
Warning nodes       : 0

Agent Health Test   : passed

Basic validation that checks device states as they were 4 hours ago:

cumulus@switch:~$ netq check agents around 4h
agent check result summary:

Total nodes         : 21
Checked nodes       : 21
Failed nodes        : 0
Rotten nodes        : 0
Warning nodes       : 0

Agent Health Test   : passed

netq show agents
netq show unit-tests agent
netq add validation
netq config agent

netq check bgp

Validates that all configured route peering is established in your network fabric by looking for consistency across BGP sessions; in particular, whether duplicate router IDs exist and if any sessions are in the unestablished state. If you have nodes that implement virtual routing and forwarding (VRF), you can request status based on the relevant routing table. VRF is commonly configured in multi-tenancy deployments to maintain separate domains for each tenant.

The output displays the status (passed/failed/skipped) of all tests and a summary including:

Total number of nodes found
Number of nodes validated
Number of nodes that failed the validation
Number of nodes that have been silent for 120 seconds (rotten)
Number of nodes with warnings
Total number of BGP sessions at the specified time
Number of sessions that have failed to establish a connection

Syntax

netq check bgp 
    [label <text-label-name> | hostnames <text-list-hostnames>]
    [vrf <vrf>]
    [check_filter_id <text-check-filter-id>]
    [include <bgp-number-range-list> | exclude <bgp-number-range-list>]
    [around <text-time>]
    [json | summary]

Required Arguments

None

Options

Option	Value	Description
label	<text-label-name>	Reserved
hostnames	<text-list-hostnames>	Comma-separated list (no spaces) of hostnames to include in validation
vrf	<vrf>	When you configure a VRF, the accepted values include: default: use the default routing table mgmt: use management routing table <custom>: use user-defined routing table
check_filter_id	<text-check-filter-id>	Include the specific filter for a validation
include	<agent-number-range-list>	Include the specified validation tests
exclude	<agent-number-range-list>	Exclude the specified validation tests
around	<text-time>	Indicates how far to go back in time for the network state information. Write the value using text (versus a UTP representation for example). Note there is no space between the number and unit of time. Valid values include: <1-xx>s: number of seconds <1-xx>m: number of minutes <1-xx>h: number of hours <1-xx>d: number of days
json	NA	Display the output in JSON format
summary	NA	Display only the summary information and test results. Do not display details for tests that failed or had warnings.

Sample Usage

The following example reports 8 errors from the ‘session establishment’ test. To fix these errors, bring up the items that are in a down state. Then rerun the command to verify the new configuration.

cumulus@switch:~$ netq check bgp
bgp check result summary:

Total nodes         : 13
Checked nodes       : 13
Failed nodes        : 2
Rotten nodes        : 0
Warning nodes       : 0
Skipped nodes       : 0

Additional summary:
Failed Sessions     : 8
Total Sessions      : 228


Session Establishment Test   : 0 warnings, 8 errors
Address Families Test        : passed
Router ID Test               : passed
Hold Time Test               : passed
Keep Alive Interval Test     : passed
Ipv4 Stale Path Time Test    : passed
Ipv6 Stale Path Time Test    : passed
Interface MTU Test           : passed


Session Establishment Test details:
Hostname          VRF             Peer Name         Peer Hostname     Reason                                        Last Changed
----------------- --------------- ----------------- ----------------- --------------------------------------------- -------------------------
spine-1           DataVrf1080     swp7.2            tor-1             BGP session with peer tor-1 (swp7.2 vrf DataV Wed May  3 11:12:35 2023
                                                                      rf1080) failed, reason: BFD down received
spine-1           DataVrf1081     swp7.3            tor-1             BGP session with peer tor-1 (swp7.3 vrf DataV Wed May  3 11:12:35 2023
                                                                      rf1081) failed, reason: BFD down received
spine-1           DataVrf1082     swp7.4            tor-1             BGP session with peer tor-1 (swp7.4 vrf DataV Wed May  3 11:12:35 2023
                                                                      rf1082) failed, reason: BFD down received
spine-1           default         swp7              tor-1             BGP session with peer tor-1 (swp7 vrf default Wed May  3 11:12:34 2023
                                                                      ) failed, reason: BFD down received
tor-1             DataVrf1080     swp3.2            spine-1           BGP session with peer spine-1 (swp3.2 vrf Dat Wed May  3 11:12:38 2023
                                                                      aVrf1080) failed, reason: Link Admin Down
tor-1             DataVrf1081     swp3.3            spine-1           BGP session with peer spine-1 (swp3.3 vrf Dat Wed May  3 11:12:38 2023
                                                                      aVrf1081) failed, reason: Link Admin Down
tor-1             DataVrf1082     swp3.4            spine-1           BGP session with peer spine-1 (swp3.4 vrf Dat Wed May  3 11:12:38 2023
                                                                      aVrf1082) failed, reason: Link Admin Down
tor-1             default         swp3              spine-1           BGP session with peer spine-1 (swp3 vrf defau Wed May  3 11:12:38 2023
                                                                      lt) failed, reason: Link Admin Down

netq show bgp
netq show unit-tests bgp
netq add validation

netq check cl-version

Verifies the Cumulus Linux version is consistent across nodes, matches a specified version, or is greater than or equal to a specified version, based on the options chosen.

Syntax

netq check cl-version
    [label <text-label-name> | hostnames <text-list-hostnames>]
    [match-version <cl-ver> | min-version <cl-ver>]
    [check_filter_id <text-check-filter-id>]
    [include <version-number-range-list> | exclude <version-number-range-list>]
    [around <text-time>]
    [json | summary]

Required Arguments

None

Options

Option	Value	Description
label	<text-label-name>	Reserved
hostnames	<text-list-hostnames>	Comma-separated list (no spaces) of hostnames to include in validation
match-version	<cl-ver>	Identifies all switches with a Cumulus Linux version other than the one specified with this option. Specify `cl-ver` values in x.y.z format, for example 4.2.0.
min-version	<cl-ver>	Identifies all switches with a Cumulus Linux version older than the one specified with this option. Specify `cl-ver` values in x.y.z format, for example 3.7.12.
check_filter_id	<text-check-filter-id>	Include the specific filter for a validation
include	<agent-number-range-list>	Include the specified validation tests
exclude	<agent-number-range-list>	Exclude the specified validation tests
around	<text-time>	Indicates how far to go back in time for the network state information. Write the value using text (versus a UTP representation for example). Note there is no space between the number and unit of time. Valid values include: <1-xx>s: number of seconds <1-xx>m: number of minutes <1-xx>h: number of hours <1-xx>d: number of days
json	NA	Display the output in JSON format
summary	NA	Display only the summary information and test results. Do not display details for tests that failed or had warnings.

Sample Usage

cumulus@switch:~$ netq check cl-version
version check result summary:

Total nodes         : 21
Checked nodes       : 21
Failed nodes        : 0
Rotten nodes        : 0
Warning nodes       : 0

Cumulus Linux Image Version Test   : passed

List devices which do not match a version:

cumulus@switch:~$ netq check cl-version match-version 3.7.12
version check result summary:

Total nodes         : 21
Checked nodes       : 21
Failed nodes        : 12
Rotten nodes        : 0
Warning nodes       : 0

Cumulus Linux Image Version Test   : 0 warnings, 12 errors

Cumulus Linux Image Version Test details:
Hostname          Entity       Version                              Reason
----------------- ------------ ------------------------------------ ---------------------------------------------
border01          OS           4.2.1                                unexpected os version 4.2.1, should be 3.7.12
border02          OS           4.2.1                                unexpected os version 4.2.1, should be 3.7.12
fw1               OS           4.2.1                                unexpected os version 4.2.1, should be 3.7.12
fw2               OS           4.2.1                                unexpected os version 4.2.1, should be 3.7.12
leaf01            OS           4.2.1                                unexpected os version 4.2.1, should be 3.7.12
leaf02            OS           4.2.1                                unexpected os version 4.2.1, should be 3.7.12
leaf03            OS           4.2.1                                unexpected os version 4.2.1, should be 3.7.12
leaf04            OS           4.2.1                                unexpected os version 4.2.1, should be 3.7.12
spine01           OS           4.2.1                                unexpected os version 4.2.1, should be 3.7.12
spine02           OS           4.2.1                                unexpected os version 4.2.1, should be 3.7.12
spine03           OS           4.2.1                                unexpected os version 4.2.1, should be 3.7.12
spine04           OS           4.2.1                                unexpected os version 4.2.1, should be 3.7.12

List devices with a version greater than or equal to a version:

cumulus@switch:~$ netq check cl-version min-version 3.7.12
version check result summary:

Total nodes         : 21
Checked nodes       : 21
Failed nodes        : 0
Rotten nodes        : 0
Warning nodes       : 0

Cumulus Linux Image Version Test   : passed

netq show unit-tests cl-version

netq check evpn

Verifies communication status for all nodes (leafs, spines, and hosts) running instances of Ethernet VPN (EVPN) in your network fabric. In particular, it looks for:

BGP and EVPN session establishment
VNI type consistency
VLAN consistency among participating devices
VRF consistency among participating devices

The output displays the status (passed/failed/skipped) of all tests and a summary including:

Total number of nodes found
Number of nodes validated
Number of nodes that failed the validation
Number of nodes that have been silent for 120 seconds (rotten)
Number of nodes with warnings
Total number of VNIs
Number of failed BGP sessions
Total number of sessions

Syntax

netq check evpn
    [label <text-label-name> | hostnames <text-list-hostnames>]
    [check_filter_id <text-check-filter-id>]
    [include <evpn-number-range-list> | exclude <evpn-number-range-list>]
    [around <text-time>]
    [json | summary]

Required Arguments

None

Options

Option	Value	Description
label	<text-label-name>	Reserved
hostnames	<text-list-hostnames>	Comma-separated list (no spaces) of hostnames to include in validation
check_filter_id	<text-check-filter-id>	Include the specific filter for a validation
include	<agent-number-range-list>	Include the specified validation tests
exclude	<agent-number-range-list>	Exclude the specified validation tests
around	<text-time>	Indicates how far to go back in time for the network state information. Write the value using text (versus a UTP representation for example). Note there is no space between the number and unit of time. Valid values include: <1-xx>s: number of seconds <1-xx>m: number of minutes <1-xx>h: number of hours <1-xx>d: number of days
json	NA	Display the output in JSON format
summary	NA	Display only the summary information and test results. Do not display details for tests that failed or had warnings.

Sample Usage

The following example reports an error for the ‘EVPN-BGP session’ test. To fix the error, bring up the interface that is in a down state. Run the test again to verify the new configuration.

cumulus@switch:~$: netq check evpn
evpn check result summary:

Total nodes         : 6
Checked nodes       : 6
Failed nodes        : 1
Rotten nodes        : 0
Warning nodes       : 0
Skipped nodes       : 0

Additional summary:
Total VNIs          : 13
Failed EVPN Sessions: 1
Total EVPN Sessions : 47


EVPN BGP Session Test            : 0 warnings, 1 errors
EVPN VNI Type Consistency Test   : passed
EVPN Type 2 Test                 : skipped
EVPN Type 3 Test                 : passed
EVPN Session Test                : passed
Vlan Consistency Test            : passed
Vrf Consistency Test             : passed


EVPN BGP Session Test details:
Hostname          Peer Name         Peer Hostname     Reason                                        Last Changed
----------------- ----------------- ----------------- --------------------------------------------- -------------------------
tor-1             swp3              spine-1           BGP session with peer spine-1 (swp3 vrf defau Wed May  3 11:12:34 2023
                                                      lt) failed, reason: Interface down

netq show evpn
netq show unit-tests evpn
netq add validation

netq check interfaces

Verifies interface communication status for all nodes (leafs, spines, and hosts) or an interface between specific nodes in your network fabric. In particular, it looks for:

Administrative and operational state status
Link speed consistency
Consistency of auto-negotiation settings

The output displays the status (passed/failed/skipped) of all tests and a summary including:

Total number of nodes found
Number of nodes validated
Number of nodes that failed validation
Number of nodes that have been silent for 120 seconds (rotten)
Number of nodes with warnings
Number of ports validated
Number of ports that failed validation
Number of unverified ports (no peer found for the node)

This command only checks the physical interfaces; it does not check bridges, bonds, or other software constructs.

Syntax

netq check interfaces
    [hostnames <text-list-hostnames>]
    [check_filter_id <text-check-filter-id>]
    [include <interface-number-range-list> | exclude <interface-number-range-list>]
    [around <text-time>]
    [json | summary]

Required Arguments

None

Options

Option	Value	Description
hostnames	<text-list-hostnames>	Comma-separated list (no spaces) of hostnames to include in validation
check_filter_id	<text-check-filter-id>	Include the specific filter for a validation
include	<agent-number-range-list>	Include the specified validation tests
exclude	<agent-number-range-list>	Exclude the specified validation tests
around	<text-time>	Indicates how far to go back in time for the network state information. Write the value using text (versus a UTP representation for example). Note there is no space between the number and unit of time. Valid values include: <1-xx>s: number of seconds <1-xx>m: number of minutes <1-xx>h: number of hours <1-xx>d: number of days
json	NA	Display the output in JSON file format instead of default on-screen text format
summary	NA	Display only the summary information and test results. Do not display details for tests that failed or had warnings..

Sample Usage

cumulus@switch:~$ netq check interfaces
interface check result summary:

Total nodes         : 21
Checked nodes       : 21
Failed nodes        : 6
Rotten nodes        : 0
Warning nodes       : 0

Additional summary:
Checked Ports       : 145
Failed Ports        : 12
Unverified Ports    : 69

Admin State Test   : passed
Oper State Test    : passed
Speed Test         : passed
Autoneg Test       : 0 warnings, 12 errors

Autoneg Test details:
Hostname          Interface                 Peer Hostname     Peer Interface            Message                             Last Changed
----------------- ------------------------- ----------------- ------------------------- ----------------------------------- -------------------------
server01          eth1                      leaf01            swp1                      Autoneg mismatch (on, off)          Wed Nov 18 21:58:07 2020 
server01          eth2                      leaf02            swp1                      Autoneg mismatch (on, off)          Wed Nov 18 21:58:07 2020 
server02          eth1                      leaf01            swp2                      Autoneg mismatch (on, off)          Wed Nov 18 21:58:07 2020 
server02          eth2                      leaf02            swp2                      Autoneg mismatch (on, off)          Wed Nov 18 21:58:07 2020 
server03          eth1                      leaf01            swp3                      Autoneg mismatch (on, off)          Wed Nov 18 21:58:07 2020 
server03          eth2                      leaf02            swp3                      Autoneg mismatch (on, off)          Wed Nov 18 21:58:07 2020 
server04          eth1                      leaf03            swp1                      Autoneg mismatch (on, off)          Wed Nov 18 21:58:07 2020 
server04          eth2                      leaf04            swp1                      Autoneg mismatch (on, off)          Wed Nov 18 21:58:07 2020 
server05          eth1                      leaf03            swp2                      Autoneg mismatch (on, off)          Wed Nov 18 21:58:07 2020 
server05          eth2                      leaf04            swp2                      Autoneg mismatch (on, off)          Wed Nov 18 21:58:07 2020 
server06          eth1                      leaf03            swp3                      Autoneg mismatch (on, off)          Wed Nov 18 21:58:07 2020 
server06          eth2                      leaf04            swp3                      Autoneg mismatch (on, off)          Wed Nov 18 21:58:07 2020

cumulus@switch:~$ netq check interfaces summary
interface check result summary:

Total nodes         : 21
Checked nodes       : 21
Failed nodes        : 6
Rotten nodes        : 0
Warning nodes       : 0

Additional summary:
Checked Ports       : 145
Failed Ports        : 12
Unverified Ports    : 69

Admin State Test   : passed
Oper State Test    : passed
Speed Test         : passed
Autoneg Test       : 0 warnings, 12 errors

This example checks for configuration mismatches and finds a link speed mismatch on server03. The link speed on swp49 is 40G and the peer port swp50 shows as unknown.

cumulus@switch:~$ netq check interfaces
Checked Nodes: 10, Failed Nodes: 1
Checked Ports: 125, Failed Ports: 2, Unverified Ports: 35
Hostname          Interface                 Peer Hostname     Peer Interface            Message
----------------- ------------------------- ----------------- ------------------------- -----------------------------------
server03          swp49                     server03          swp50                     Speed mismatch (40G, Unknown)      
server03          swp50                     server03          swp49                     Speed mismatch (Unknown, 40G)

cumulus@switch:~$ netq check interfaces
Checked Nodes: 18, Failed Nodes: 8
Checked Ports: 741, Failed Ports: 1, Unverified Ports: 414
 
Matching cables records:
Hostname          Interface                 Peer Hostname     Peer Interface            Message
----------------- ------------------------- ----------------- ------------------------- -----------------------------------
leaf02            -                         -                 -                         Link flapped 11 times in last 5
                                                                                        mins

netq show interfaces physical
netq show unit-tests interfaces
netq add validation

netq check mlag

Verifies MLAG session consistency by identifying all MLAG peers with errors or misconfigurations in the NetQ domain. In particular, it looks for:

multiple link pairs with the same system MAC address
any interfaces with only a single attachment
peer connectivity
conflicted bonds
whether the backup IP address is pointing to the correct peer

The output displays the status (passed/failed/skipped) of all tests and a summary including:

Total number of nodes found
Number of nodes validated
Number of nodes that failed the validation
Number of nodes that have been silent for 120 seconds (rotten)
Number of nodes with warnings

Syntax

netq check mlag
    [label <text-label-name> | hostnames <text-list-hostnames>]
    [check_filter_id <text-check-filter-id>]
    [include <mlag-number-range-list> | exclude <mlag-number-range-list>]
    [around <text-time>]
    [json | summary]

Required Arguments

None

Options

Option	Value	Description
label	<text-label-name>	Reserved
hostnames	<text-list-hostnames>	Comma-separated list (no spaces) of hostnames to include in validation
check_filter_id	<text-check-filter-id>	Include the specific filter for a validation
include	<agent-number-range-list>	Include the specified validation tests
exclude	<agent-number-range-list>	Exclude the specified validation tests
around	<text-time>	Indicates how far to go back in time for the network state information. Write the value using text (versus a UTP representation for example). Note there is no space between the number and unit of time. Valid values include: <1-xx>s: number of seconds <1-xx>m: number of minutes <1-xx>h: number of hours <1-xx>d: number of days
json	NA	Display the output in JSON file format instead of default on-screen text format
summary	NA	Display only the summary information and test results. Do not display details for tests that failed or had warnings.

Sample Usage

The following example runs a check on two devices: noc-se and noc-pr. The output reports several errors, including a peerlink MTU mismatch, a bond MTU mismatch, a bond in a conflicted state, and a singly-connected bond. To resolve these errors, reconfigure the mismatched values and bring up the bond interface that is in a down state. Then run the command again to verify the new configurations.

cumulus@switch:~$ netq check mlag hostnames noc-se,noc-pr
mlag check result summary:

Total nodes                             : 2
Checked nodes                           : 2
Failed nodes                            : 2
Rotten nodes                            : 0
Warning nodes                           : 0
Skipped nodes                           : 0
Checked nodes hostname                  : noc-se, noc-pr


Peering Test             : 0 warnings, 2 errors
Backup IP Test           : passed
Clag SysMac Test         : passed
VXLAN Anycast IP Test    : passed
Bridge Membership Test   : passed
Spanning Tree Test       : passed
Dual Home Test           : 0 warnings, 2 errors
Single Home Test         : passed
Conflicted Bonds Test    : 0 warnings, 5 errors
ProtoDown Bonds Test     : passed
SVI Test                 : passed


Peering Test details:
Hostname          Reason
----------------- ---------------------------------------------
noc-pr            Peerlink peerlink-1.4094 MTU mismatch        
noc-se            Peerlink peerlink-1.4094 MTU mismatch        


Dual Home Test details:
Hostname          Reason
----------------- ---------------------------------------------
noc-pr            Dually connected bond NetQBond-3 MTU mismatch
                  with peer noc-se:NetQBond-3                  
noc-se            Dually connected bond NetQBond-3 MTU mismatch
                  with peer noc-pr:NetQBond-3                  
Conflicted Bonds Test details:
Hostname          Reason
----------------- ---------------------------------------------
noc-pr            Bond NetQBond-1 in Conflicted state due to ma
                  tching clagid not configured on peer         
noc-pr            Bond NetQBond-2 in Conflicted state due to ma
                  tching clagid not configured on peer         
noc-pr            Bond NetQBond-4 in Conflicted state due to no
                  t found in peer                              
noc-se            Bond NetQBond-1 in Conflicted state due to ma
                  tching clagid not configured on peer         
noc-se            Bond NetQBond-2 in Conflicted state due to ma
                  tching clagid not configured on peer

netq show mlag
netq show unit-tests mlag
netq add validation

netq check mtu

Verifies consistency of the maximum transmission unit (MTU) across all links in your network fabric. The command verifies the MTU consistency at the level appropriate to the specific type of link. For example, bond interfaces have their MTU enforced at the bond level and not at the individual slave level. For MLAG/CLAG bonds, verification confirms whether both ends of the bond have the same MTU value configured for their local instance of the bond. You can also view nodes without a peer link.

The output displays the status (passed/failed/skipped) of all tests and a summary including:

Total number of nodes found
Number of nodes validated
Number of nodes that failed validation
Number of nodes that have been silent for 120 seconds (rotten)
Number of nodes with warnings
Number of links validated
Number of links that failed validation
Number of links that had warnings

Syntax

netq check mtu
    [label <text-label-name> | hostnames <text-list-hostnames>]
    [unverified]
    [check_filter_id <text-check-filter-id>]
    [include <mtu-number-range-list> | exclude <mtu-number-range-list>]
    [around <text-time>]
    [json | summary]

Required Arguments

None

Options

Option	Value	Description
label	<text-label-name>	Reserved
hostnames	<text-list-hostnames>	Comma-separated list (no spaces) of hostnames to include in validation
unverified	NA	Find nodes without a known peer link
check_filter_id	<text-check-filter-id>	Include the specific filter for a validation
include	<agent-number-range-list>	Include the specified validation tests
exclude	<agent-number-range-list>	Exclude the specified validation tests
around	<text-time>	Indicates how far to go back in time for the network state information. Write the value using text (versus a UTP representation for example). Note there is no space between the number and unit of time. Valid values include: <1-xx>s: number of seconds <1-xx>m: number of minutes <1-xx>h: number of hours <1-xx>d: number of days
json	NA	Display the output in JSON format
summary	NA	Display only the summary information and test results. Do not display details for tests that failed or had warnings.

Sample Usage

cumulus@switch:~$ netq check mtu
mtu check result summary:

Total nodes         : 21
Checked nodes       : 21
Failed nodes        : 3
Rotten nodes        : 0
Warning nodes       : 0

Additional summary:
Checked Links       : 291
Failed Links        : 8
Warn Links          : 0

Link MTU Consistency Test   : 0 warnings, 8 errors
VLAN interface Test         : passed
Bridge interface Test       : passed

Link MTU Consistency Test details:
Hostname          Interface                 MTU    Peer              Peer Interface            Peer MTU Reason
----------------- ------------------------- ------ ----------------- ------------------------- -------- ---------------------------------------------
border01          bond3                     9000   fw1               borderBond                9216     MTU Mismatch                                 
border01          swp3                      9000   fw1               swp1                      9216     MTU Mismatch                                 
border02          bond3                     9000   fw1               borderBond                9216     MTU Mismatch                                 
border02          swp3                      9000   fw1               swp2                      9216     MTU Mismatch                                 
fw1               borderBond                9216   border01          bond3                     9000     MTU Mismatch                                 
fw1               borderBond                9216   border02          bond3                     9000     MTU Mismatch                                 
fw1               swp1                      9216   border01          swp3                      9000     MTU Mismatch                                 
fw1               swp2                      9216   border02          swp3                      9000     MTU Mismatch

Add nodes without peer links to output:

cumulus@switch:~$ netq check mtu unverified
mtu check result summary:

Total nodes         : 21
Checked nodes       : 21
Failed nodes        : 3
Rotten nodes        : 0
Warning nodes       : 0

Additional summary:
Checked Links       : 291
Failed Links        : 8
Warn Links          : 0

Link MTU Consistency Test   : 0 warnings, 8 errors
VLAN interface Test         : passed
Bridge interface Test       : passed

Link MTU Consistency Test details:
Hostname          Interface                 MTU    Peer              Peer Interface            Peer MTU Reason
----------------- ------------------------- ------ ----------------- ------------------------- -------- ---------------------------------------------
border01          bond3                     9000   fw1               borderBond                9216     MTU Mismatch                                 
border01          swp3                      9000   fw1               swp1                      9216     MTU Mismatch                                 
border02          bond3                     9000   fw1               borderBond                9216     MTU Mismatch                                 
border02          swp3                      9000   fw1               swp2                      9216     MTU Mismatch                                 
fw1               borderBond                9216   border01          bond3                     9000     MTU Mismatch                                 
fw1               borderBond                9216   border02          bond3                     9000     MTU Mismatch                                 
fw1               swp1                      9216   border01          swp3                      9000     MTU Mismatch                                 
fw1               swp2                      9216   border02          swp3                      9000     MTU Mismatch                                 

Link MTU Consistency Test unverified:
Hostname          Interface                 MTU    Peer              Peer Interface            Peer MTU Reason
----------------- ------------------------- ------ ----------------- ------------------------- -------- ---------------------------------------------
oob-mgmt-server   vagrant                   1500   -                 -                         -        No Peer link info

netq show unit-tests mtu
netq add validation

netq check ntp

Verifies network time synchronization using NTP for all nodes (leafs, spines, and hosts) in your network fabric. Nodes that are not in time synchronization with the NetQ appliance or VM might report data with an incorrect timestamp or lose communication altogether.

The output displays the status (passed/failed/skipped) of all tests and a summary including:

Total number of nodes found
Number of nodes validated
Number of nodes that failed validation
Number of nodes that have been silent for 120 seconds (rotten)
Number of nodes with warnings
Number of nodes found that are unknown to NetQ
Number of NTP servers available for synchronization

Syntax

netq check ntp
    [label <text-label-name> | hostnames <text-list-hostnames>]
    [check_filter_id <text-check-filter-id>]
    [include <ntp-number-range-list> | exclude <ntp-number-range-list>]
    [around <text-time>]
    [json | summary]

Required Arguments

None

Options

Option	Value	Description
label	<text-label-name>	Reserved
hostnames	<text-list-hostnames>	Comma-separated list (no spaces) of hostnames to include in validation
check_filter_id	<text-check-filter-id>	Include the specific filter for a validation
include	<agent-number-range-list>	Include the specified validation tests
exclude	<agent-number-range-list>	Exclude the specified validation tests
around	<text-time>	Indicates how far to go back in time for the network state information. Write the value using text (versus a UTP representation for example). Note there is no space between the number and unit of time. Valid values include: <1-xx>s: number of seconds <1-xx>m: number of minutes <1-xx>h: number of hours <1-xx>d: number of days
json	NA	Display the output in JSON format
summary	NA	Display only the summary information and test results. Do not display details for tests that failed or had warnings.

Sample Usage

cumulus@switch:~$ netq check ntp
ntp check result summary:

Total nodes         : 21
Checked nodes       : 21
Failed nodes        : 2
Rotten nodes        : 0
Warning nodes       : 0

Additional summary:
Unknown nodes       : 0
NTP Servers         : 2

NTP Sync Test   : 0 warnings, 2 errors

NTP Sync Test details:
Hostname          NTP Sync Connect Time
----------------- -------- -------------------------
fw1               no       2020-11-18 19:50:31
fw2               no       2020-11-18 19:50:46

netq show ntp
netq show unit-tests ntp
netq add validation

netq check ospf

Validates that all configured route peering is established in your network fabric by looking for consistency across OSPF sessions; in particular, whether duplicate router IDs exist and if any sessions are in the unestablished state.

The output displays the status (passed/failed/skipped) of all tests and a summary including:

Total number of nodes found
Number of nodes validated
Number of nodes that failed validation (reporting session failures)
Number of nodes that have been silent for 120 seconds (rotten)
Number of nodes with warnings
Number of nodes with failed adjacencies
Total number of adjacencies

Syntax

netq check ospf
    [label <text-label-name> | hostnames <text-list-hostnames>]
    [check_filter_id <text-check-filter-id>]
    [include <ospf-number-range-list> | exclude <ospf-number-range-list>]
    [around <text-time>]
    [json | summary]

Required Arguments

None

Options

Option	Value	Description
label	<text-label-name>	Reserved
hostnames	<text-list-hostnames>	Comma-separated list (no spaces) of hostnames to include in validation
check_filter_id	<text-check-filter-id>	Include the specific filter for a validation
include	<agent-number-range-list>	Include the specified validation tests
exclude	<agent-number-range-list>	Exclude the specified validation tests
around	<text-time>	Indicates how far to go back in time for the network state information. Write the value using text (versus a UTP representation for example). Note there is no space between the number and unit of time. Valid values include: <1-xx>s: number of seconds <1-xx>m: number of minutes <1-xx>h: number of hours <1-xx>d: number of days
json	NA	Display the output in JSON format
summary	NA	Display only the summary information and test results. Do not display details for tests that failed or had warnings.

Sample Usage

The default validation runs a networkwide OSPF connectivity and configuration check on all nodes running the OSPF service. This example shows errors in the timers and interface MTU tests.

cumulus@switch:~# netq check ospf
Checked nodes: 8, Total nodes: 8, Rotten nodes: 0, Failed nodes: 4, Warning nodes: 0, Failed Adjacencies: 4, Total Adjacencies: 24

Router ID Test        : passed
Adjacency Test        : passed
Timers Test           : 0 warnings, 4 errors
Network Type Test     : passed
Area ID Test          : passed
Interface Mtu Test    : 0 warnings, 2 errors
Service Status Test   : passed

Timers Test details:
Hostname          Interface                 PeerID                    Peer IP                   Reason                                        Last Changed
----------------- ------------------------- ------------------------- ------------------------- --------------------------------------------- -------------------------
spine-1           downlink-4                torc-22                   uplink-1                  dead time mismatch                            Mon Jul  1 16:18:33 2019 
spine-1           downlink-4                torc-22                   uplink-1                  hello time mismatch                           Mon Jul  1 16:18:33 2019 
torc-22           uplink-1                  spine-1                   downlink-4                dead time mismatch                            Mon Jul  1 16:19:21 2019 
torc-22           uplink-1                  spine-1                   downlink-4                hello time mismatch                           Mon Jul  1 16:19:21 2019 

Interface Mtu Test details:
Hostname          Interface                 PeerID                    Peer IP                   Reason                                        Last Changed
----------------- ------------------------- ------------------------- ------------------------- --------------------------------------------- -------------------------
spine-2           downlink-6                0.0.0.22                  27.0.0.22                 mtu mismatch                                  Mon Jul  1 16:19:02 2019 
tor-2             uplink-2                  0.0.0.20                  27.0.0.20                 mtu mismatch                                  Mon Jul  1 16:19:37 2019

netq show ospf
netq show unit-tests ospf
netq add validation

netq check roce

Searches for consistent RoCE and QoS configurations across nodes.

Syntax

netq check roce
    [hostnames <text-list-hostnames>] 
    [check_filter_id <text-check-filter-id>] 
    [include <roce-number-range-list> | exclude <roce-number-range-list>] 
    [around <text-time>] 
    [json | summary]

Required Arguments

None

Options

Option	Value	Description
hostnames	<text-list-hostnames>	Comma-separated list (no spaces) of hostnames to include in validation
check_filter_id	<text-check-filter-id>	Include the specific filter for a validation
include	<roce-number-range-list>	Include the specified validation tests
exclude	<roce-number-range-list>	Exclude the specified validation tests
around	<text-time>	Indicates how far to go back in time for the network state information. Write the value using text (versus a UTP representation for example). Note there is no space between the number and unit of time. Valid values include: <1-xx>s: number of seconds <1-xx>m: number of minutes <1-xx>h: number of hours <1-xx>d: number of days
json	NA	Display the output in JSON format
summary	NA	Display only the summary information and test results. Do not display details for tests that failed or had warnings.

Sample Usage

The following example displays several RoCE errors in the network’s fabric. The ‘RoCE mode test’ indicates that switches are running in both lossy and lossless modes, which must be reconciled. The other errors report configuration mismatches along with the expected configurations. To fix these errors, reconfigure RoCE according to the recommendations reported in the output. Then run the command again to verify its accuracy.

cumulus@switch:mgmt:~$ netq check roce
roce check result summary:

Total nodes                             : 2
Checked nodes                           : 2
Failed nodes                            : 2
Rotten nodes                            : 0
Warning nodes                           : 0
Skipped nodes                           : 0
Checked nodes hostname                  : mlx-3700c-23, mlx-3700c-24

RoCE mode Test                 : 0 warnings, 1 errors
RoCE Classification Test       : 0 warnings, 3 errors
RoCE Congestion Control Test   : 0 warnings, 2 errors
RoCE Flow Control Test         : 0 warnings, 2 errors
RoCE ETS mode Test             : passed


RoCE mode Test details:
Hostname          Reason
----------------- ---------------------------------------------
mlx-3700c-24      RoCE Lossy mode inconsistent with mlx-3700c-2
                  3                                            
RoCE Classification Test details:
Hostname          Reason
----------------- ---------------------------------------------
mlx-3700c-23      Invalid traffic-class mapping for switch-prio
                  rity 4.Expected 0 Got 3                      
mlx-3700c-24      DSCP mapping config invalid for switch-prio 3
                  .Expected DSCP: 24,25,26,27,28,29,30,31.  
                  DSCP mapping config invalid for switch-prio 5.
                  Expected DSCP: 40,41,42,43,44,45,46,47.        
mlx-3700c-24      PCP mapping config invalid for switch-prio 3.
                  Expected PCP: 3. PCP mapping config invalid f
                  or switch-prio 4.Expected PCP: 4.            
RoCE Congestion Control Test details:
Hostname          Reason
----------------- ---------------------------------------------
mlx-3700c-23      Congestion Config TC Mismatch.Expected enable
                  d-tc: 0,3.                                   
mlx-3700c-23      Congestion Config mode Mismatch.Expected cong
                  estion-mode: ECN.                            
RoCE Flow Control Test details:
Hostname          Reason
----------------- ---------------------------------------------
mlx-3700c-23      Invalid RoCE PFC rx-enabled flag.Expected: en
                  abled.                                       
mlx-3700c-23      RoCE PFC Priority Mismatch.Expected pfc-prior
                  ity: 3.

netq show roce-counters
netq show roce-config
netq show roce-counters pool
netq show events
netq show unit-tests

netq check sensors

Verifies the status of temperature, cooling fan, and power supply sensors for all nodes in your network fabric.

The output displays the status (passed/failed/skipped) of all tests and a summary including:

Total number of nodes found
Number of nodes validated
Number of nodes that failed validation
Number of nodes that have been silent for 120 seconds (rotten)
Number of nodes with warnings
Number of sensors validated
Number of sensors that failed validation

Syntax

netq check sensors
    [hostnames <text-list-hostnames>]
    [check_filter_id <text-check-filter-id>]
    [include <sensors-number-range-list> | exclude <sensors-number-range-list>]
    [around <text-time>]
    [json | summary]

Required Arguments

None

Options

Option	Value	Description
hostnames	<text-list-hostnames>	Comma-separated list (no spaces) of hostnames to include in validation
check_filter_id	<text-check-filter-id>	Include the specific filter for a validation
include	<agent-number-range-list>	Include the specified validation tests
exclude	<agent-number-range-list>	Exclude the specified validation tests
around	<text-time>	Indicates how far to go back in time for the network state information. Write the value using text (versus a UTP representation for example). Note there is no space between the number and unit of time. Valid values include: <1-xx>s: number of seconds <1-xx>m: number of minutes <1-xx>h: number of hours <1-xx>d: number of days
json	NA	Display the output in JSON format
summary	NA	Display only the summary information and test results. Do not display details for tests that failed or had warnings.

Sample Usage

cumulus@switch:~$ netq check sensors
sensors check result summary:

Total nodes         : 13
Checked nodes       : 13
Failed nodes        : 0
Rotten nodes        : 0
Warning nodes       : 0

Additional summary:
Checked Sensors     : 102
Failed Sensors      : 0


PSU sensors Test           : passed
Fan sensors Test           : passed
Temperature sensors Test   : passed

netq show sensors
netq show unit-tests sensors
netq add validation

netq check vlan

Verifies consistency of the virtual local area network (VLAN) nodes and interfaces across all links in your network fabric. In particular, it looks for link neighbor and MLAG bond consistency. You can also identify nodes without peers.

The output displays the status (passed/failed/skipped) of all tests and a summary including:

Total number of nodes found
Number of nodes validated
Number of nodes that failed validation
Number of nodes that have been silent for 120 seconds (rotten)
Number of nodes with warnings
Total number of links found
Number of links that failed validation

Syntax

netq check vlan
    [label <text-label-name> | hostnames <text-list-hostnames>]
    [unverified]
    [check_filter_id <text-check-filter-id>] 
    [include <vlan-number-range-list> | exclude <vlan-number-range-list>]
    [around <text-time>]
    [json | summary]

Required Arguments

None

Options

Option	Value	Description
label	<text-label-name>	Reserved
hostnames	<text-list-hostnames>	Comma-separated list (no spaces) of hostnames to include in validation
unverified	NA	Find nodes with no peer
check_filter_id	<text-check-filter-id>	Include the specific filter for a validation
include	<agent-number-range-list>	Include the specified validation tests
exclude	<agent-number-range-list>	Exclude the specified validation tests
around	<text-time>	Indicates how far to go back in time for the network state information. Write the value using text (versus a UTP representation for example). Note there is no space between the number and unit of time. Valid values include: <1-xx>s: number of seconds <1-xx>m: number of minutes <1-xx>h: number of hours <1-xx>d: number of days
json	NA	Display the output in JSON format
summary	NA	Display only the summary information and test results. Do not display details for tests that failed or had warnings.

Sample Usage

cumulus@switch:~$ netq check vlan
vlan check result summary:

Total nodes         : 21
Checked nodes       : 21
Failed nodes        : 3
Rotten nodes        : 0
Warning nodes       : 0

Additional summary:
Total Link Count    : 291
Failed Link Count   : 4

Link Neighbor VLAN Consistency Test   : 0 warnings, 4 errors
Clag Bond VLAN Consistency Test       : 0 warnings, 2 errors

Link Neighbor VLAN Consistency Test details:
Hostname          Interface                 VLANs                     Peer              Peer Interface            Peer VLANs                Message
----------------- ------------------------- ------------------------- ----------------- ------------------------- ------------------------- -----------------------------------
border01          bond3                     10,20,30                  fw1               borderBond                10,20                     bond3 VLAN set (10,20,30) mismatch 
                                                                                                                                            with peer fw1:borderBond (10,20)   
border02          bond3                     10,20,30                  fw1               borderBond                10,20                     bond3 VLAN set (10,20,30) mismatch 
                                                                                                                                            with peer fw1:borderBond (10,20)   
fw1               borderBond                10,20                     border01          bond3                     10,20,30                  borderBond VLAN set (10,20) mismatc
                                                                                                                                            h with peer border01:bond3 (10,20,3
                                                                                                                                            0)                                 
fw1               borderBond                10,20                     border02          bond3                     10,20,30                  borderBond VLAN set (10,20) mismatc
                                                                                                                                            h with peer border02:bond3 (10,20,3
                                                                                                                                            0)   

Clag Bond VLAN Consistency Test details:
Hostname          Interface                 VLANs                     Peer              Peer Interface            Peer VLANs                Message
----------------- ------------------------- ------------------------- ----------------- ------------------------- ------------------------- -----------------------------------
border01          bond3                     10,20,30                  -                 -                         -                         bond3 VLAN set (10,20,30) missing o
                                                                                                                                            n peerlink                         
border02          bond3                     10,20,30                  -                 -                         -                         bond3 VLAN set (10,20,30) missing o
                                                                                                                                            n peerlink

netq show vlan
netq show unit-tests vlan
netq add validation

netq check vxlan

Verifies consistency of the virtual extensible local area network (VXLAN) nodes and interfaces across all links in your network fabric. In particular, it looks for consistent VXLAN configuration and BUM replication errors.

The output displays the status (passed/failed/skipped) of all tests and a summary including:

Total number of nodes found
Number of nodes validated
Number of nodes that failed validation
Number of nodes that have been silent for 120 seconds (rotten)
Number of nodes with warnings

Syntax

netq check vxlan
    [label <text-label-name> | hostnames <text-list-hostnames>]
    [check_filter_id <text-check-filter-id>]
    [include <vxlan-number-range-list> | exclude <vxlan-number-range-list>]
    [around <text-time>]
    [json | summary]

Required Arguments

None

Options

Option	Value	Description
label	<text-label-name>	Reserved
hostnames	<text-list-hostnames>	Comma-separated list (no spaces) of hostnames to include in validation
check_filter_id	<text-check-filter-id>	Include the specific filter for a validation
include	<agent-number-range-list>	Include the specified validation tests
exclude	<agent-number-range-list>	Exclude the specified validation tests
around	<text-time>	Indicates how far to go back in time for the network state information. Write the value using text (versus a UTP representation for example). Note there is no space between the number and unit of time. Valid values include: <1-xx>s: number of seconds <1-xx>m: number of minutes <1-xx>h: number of hours <1-xx>d: number of days
json	NA	Display the output in JSON format
summary	NA	Display only the summary information and test results. Do not display details for tests that failed or had warnings.

Sample Usage

cumulus@switch:~$ netq check vxlan
vxlan check result summary:

Total nodes         : 6
Checked nodes       : 6
Failed nodes        : 0
Rotten nodes        : 0
Warning nodes       : 0

Vlan Consistency Test   : passed
BUM replication Test    : passed

netq show vxlan
netq show unit-tests vxlan
netq add validation

check

netq check addresses

Syntax

Required Arguments

Options

Sample Usage

Related Commands

netq check agents

Syntax

Required Arguments

Options

Sample Usage

Related Commands

netq check bgp

Syntax

Required Arguments

Options

Sample Usage

Related Commands

netq check cl-version

Syntax

Required Arguments

Options

Sample Usage

Related Commands

netq check evpn

Syntax

Required Arguments

Options

Sample Usage

Related Commands

netq check interfaces

Syntax

Required Arguments

Options

Sample Usage

Related Commands

netq check mlag

Syntax

Required Arguments

Options

Sample Usage

Related Commands

netq check mtu

Syntax

Required Arguments

Options

Sample Usage

Related Commands

netq check ntp

Syntax

Required Arguments

Options

Sample Usage

Related Commands

netq check ospf

Syntax

Required Arguments

Options

Sample Usage

Related Commands

netq check roce

Syntax

Required Arguments

Options

Sample Usage

Related Commands

netq check sensors

Syntax

Required Arguments

Options

Sample Usage

Related Commands

netq check vlan

Syntax

Required Arguments

Options

Sample Usage

Related Commands

netq check vxlan